• Operating voltage [V]: 12
• Rated Power [W]: 480
• Rated current [A]: 40
• Combi Switch Function: Normally Open Contact
• Number of pins: 4
• Manufacturer: JP GROUP
• Lisainfo: Relay, 12 Volt, 40 Amp
• Additional information: Relay, 12 Volt, 40 Amp

Relay function: Terminal 75, Interior Blower, Suction pipe pre-heating, Sunroof, Pump, fuel pre-supply, Start-stop system, Magnetic clutch, Surge protection, Battery main switch, Engine control unit, Normally open contact, X contact relief, Fan, engine cooling, Electric booster heater, Secondary Air System, Water pump after-run, Rear window wiper, heater/air conditioning, Clamp 15, Fuel Pump, Window Regulator, Heated windscreen, Heated rear window, Parking Heater

• Operating voltage [V]: 12
• Number of connectors: 3

Lisainfo: Relay for turn signal and emergency light, 12 Volt, 4x21 W Additional information: Relay for turn signal and emergency light, 12 Volt, 4x21 W

• Operating voltage [V]: 12
• Rated Power [W]: 120
• Rated current [A]: 10
• Combi Switch Function: Normally Open Contact
• Length [mm]: 30
• Width [mm]: 30
• Height [mm]: 42
• Connector type: 1x 2,8 mm, 5x 6,3 mm
• Number of pins: 6
• Manufacturer: JP GROUP
• Lisainfo: Relay for wiper/washer
• Additional information: Relay for wiper/washer

• Rated current [A]: 40
• Rated Voltage [V]: 12
• Number of connectors: 4
• Manufacturer: DELLO AUTOMEGA

Relay function: Normally open contact, Pre-glow device, X contact relief

• Operating Mode: Electric
• Voltage [V]: 12
• Manufacturer: DELLO AUTOMEGA

• Supplementary Article/Supplementary Info: without holder
• Housing Type: Synthetic Material Housing
• Number of pins: 5
• Rated Voltage [V]: 12
• Rated current [A]: 30
• Temperature range from [°C]: -40
• Temperature range to [°C]: 100
• General Information: relay
• Manufacturer: VIKA

Combi Switch Function: without light dimmer function, Normally Open Contact

• Number of connectors: 4
• Rated Voltage [V]: 12
• Rated current [A]: 40
• Temperature range from [°C]: -40
• Temperature range to [°C]: 85
• General Information: relay
• Manufacturer: VIKA

• Relay Number: 12
• Colour: grey
• Manufacturer: DELLO AUTOMEGA

• Relay Number: 8
• Voltage [V]: 12
• Rated current [A]: 5
• Number of pins: 6
• Manufacturer: DELLO AUTOMEGA

• Number of connectors: 4
• Manufacturer: JP GROUP

Lisainfo: Relay for fuel pump and intake manifold heating, 12 Volt, 40 Amp Additional information: Relay for fuel pump and intake manifold heating, 12 Volt, 40 Amp

• Operating voltage [V]: 12
• Rated Power [W]: 180
• Rated current [A]: 15
• Combi Switch Function: Normally Open Contact
• Resistor [Ohm]: 70
• Number of pins: 4
• Manufacturer: JP GROUP
• Lisainfo: Multifunctional Relay
• Additional information: Multifunctional Relay

Relay function: Sunroof, Fuel Pump, Tailgate, Terminal 30, Gear Lever, Licence plate light, Engine control unit, Normally open contact

• Number of pins: 4
• Rated current [A]: 15
• Resistor [Ohm]: 70
• Combi Switch Function: Normally Open Contact
• for OE number: 357906381A
• Manufacturer: DELLO AUTOMEGA

Relay function: Fuel Pump, Engine control unit, Terminal 30, Sunroof, Tailgate, Licence plate light, Gear Lever

• Voltage [V]: 12
• Number of pins: 4
• Capacity at 12V: 40A
• Manufacturer: AIC

General Information: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.

• Weight [kg]: 0.035
• Required quantity: 1
• Number of connectors: 4
• General Information: fuel pump relay
• Manufacturer: VIKA

• General Information: fuel pump relay
• Manufacturer: VIKA

• Relay Number: 67, 80, 167
• Number of connectors: 4
• Weight [kg]: 0.035
• Manufacturer: FEBI

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Weight [kg]: 0.04
• Warranty: 3 years warranty
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY
• Name: CE 96SKV005

• General Information: relay
• Manufacturer: VIKA

• General Information: fuel pump relay
• Manufacturer: VIKA

• General Information: relay
• Manufacturer: BORSEHUNG

• Construction Year to: 03.1997
• Current Strength [A]: 30
• Voltage [V]: 12
• Number of pins: 5
• Relay function: Normally open contact
• Housing Type: Synthetic Material Housing
• Combi Switch Function: without dynamic function (direction indicator)
• Protection Type (IP Code): IP34
• Temperature range from [°C]: -40
• Temperature range to [°C]: 100
• Resistor [Ohm]: 16
• Supplementary Article/Supplementary Info: without holder
• Housing Colour: black/grey
• Manufacturer: BOSCH

• Vehicle Equipment: for vehicles without trailer hitch
• Relay Number: 21, 191
• Voltage [V]: 12
• Rated Power [W]: 21
• Number of connectors: 3
• Colour: black
• Material: Plastic
• Operating Mode: Electronic
• Weight [kg]: 0.032
• Manufacturer: FEBI BILSTEIN

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Number of pins: 4
• Voltage [V]: 12
• Rated current [A]: 15
• Combi Switch Function: Normally Open Contact
• Manufacturer: AIC

General Information: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.

• General Information: control unit for wiper/washing automatic intervals
• Manufacturer: VIKA

• Voltage [V]: 12
• Number of pins: 6
• Manufacturer: AIC

General Information: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.

• Weight [kg]: 0.035
• Fitting Position: Engine Compartment
• Manufacturer: VEMO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Vehicle Equipment: for vehicles without trailer hitch
• Voltage [V]: 12
• Switching Capacity [W]: 21
• Mounting Type: Flat Plug-in Connector
• Operating Mode: Electric
• Number of pins: 3
• Plug Type: Blade Terminal
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Current Strength [A]: 40
• Relay function: Terminal 30, Clamp 87
• Rated current [A]: 40
• Weight [kg]: 0.04
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Operating voltage [V]: 12
• Switching Capacity [W]: 4x21

• Vehicle Identification Number (VIN) to: 3A-V-015 000
• Current Strength [A]: 15
• Relay function: Terminal 30, Clamp 87
• Number of pins: 4
• Voltage [V]: 12
• Colour: black
• Weight [kg]: 0.033
• Manufacturer: VEMO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Construction Year to: 03.1997
• for OE number: 111 963 141 C
• Combi Switch Function: Normally Open Contact
• Current Strength [A]: 30
• Voltage [V]: 12
• Number of pins: 5
• Relay function: Normally open contact
• Housing Type: Synthetic Material Housing
• Temperature range from [°C]: -40
• Temperature range to [°C]: 100
• Housing Colour: black
• Supplementary Article/Supplementary Info: with holder
• Resistor [Ohm]: 90
• Manufacturer: BOSCH

• General Information: control unit for radiator fan
• Manufacturer: VIKA

• General Information: relay
• Manufacturer: BORSEHUNG

• Operating voltage [V]: 12
• Rated Power [W]: 180
• Rated current [A]: 15
• Combi Switch Function: Normally Open Contact
• Temperature range to [°C]: -40
• Resistor [Ohm]: 70
• Length [mm]: 30
• Width [mm]: 30
• Height [mm]: 30
• Connector type: 3x 6,3 mm, 1x 2,8 mm
• Number of pins: 4
• Manufacturer: MEYLE

Relay function: Engine control unit, Normally open contact, Fuel Pump, Gear Lever, Sunroof, Tailgate, Licence plate light, Terminal 30

• Construction Year to: 03.1997
• for OE number: 8E0 951 253
• Combi Switch Function: On/Off Switch
• Current Strength [A]: 70
• Voltage [V]: 12
• Number of pins: 4
• Relay function: Normally open contact
• Housing Type: Housing with Plastic Lid
• Protection Type (IP Code): IP20
• Temperature range from [°C]: -40
• Temperature range to [°C]: 85
• Housing Colour: black
• Resistor [Ohm]: 63
• Length [mm]: 28
• Width [mm]: 28
• Height [mm]: 40
• Manufacturer: BOSCH

• Construction Year to: 03.1997
• for OE number: 019 193 750 3
• Current Strength [A]: 70
• Voltage [V]: 12
• Number of pins: 4
• Relay function: Normally open contact
• Temperature range from [°C]: -40
• Temperature range to [°C]: 85
• Manufacturer: BOSCH

• Fitting Position: Driver side
• Relay Number: 3/109
• Supplementary Article/Info 2: Mini Relay, with resistor
• Supplementary Article/Supplementary Info: without holder
• Protection Type (IP Code): IP54
• Voltage [V]: 12
• Temperature range from [°C]: -40
• Temperature range to [°C]: +70
• Colour: black
• Inductive Load [A]: 15
• Capacitive Load [A]: 15
• Ohmic Load [A]: 15
• Number of pins: 4
• Wiring Diagramme: X
• Combi Switch Function: Normally Open Contact
• Plug Type ID: X
• Assy./disassy. by qualified personnel required!:
• Name: HE 4RA007507081
• Manufacturer: HELLA

Relay function: Central electrics, Comfort Equipment Variant (trim package), Parking Distance Control, ABS, Low Beam, High Beam, Heated rear window, ESP, Window Regulator, Starter, Klaxon, Air Conditioning, Light switch, Fan, heater/air conditioning, Interior Blower, Clamp 15, Daytime Running Light, Convertible top hydraulics, Central Locking, ABS recovery pump, Exterior Rearview Mirror Adjustment, Heatable exterior mirror, Electric booster heater, Interior Lighting, Clamp 15R, Clamp 87, Fuel Pump, Lambda Sensor, engine cooling, Front Fog Light, Windscreen wiper, Windscreen wiper rest heating, Sunroof, Secondary Air System, Seat Heating Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Operating voltage [V]: 12
• Rated Power [W]: 120
• Rated current [A]: 10
• Combi Switch Function: Normally Open Contact
• Length [mm]: 30
• Width [mm]: 30
• Height [mm]: 42
• Connector type: 1x 2,8 mm, 5x 6,3 mm
• Number of pins: 6
• Manufacturer: MEYLE

• Vehicle Equipment: for vehicles with trailer hitch
• Relay Number: 22
• Voltage [V]: 12
• Number of connectors: 4
• Operating Mode: Electric
• Weight [kg]: 0.03
• Manufacturer: FEBI BILSTEIN

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Voltage [V]: 12
• Operating Mode: Electric
• Vehicle Equipment: for vehicles with factory mounted tow bar
• Number of pins: 4
• Weight [kg]: 0.023
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Voltage [V]: 12
• Assy./disassy. by qualified personnel required!:
• Name: HE 4RP008189151
• Manufacturer: HELLA

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Mounting Type: Plugged
• Operating Mode: Electronic
• Switching Capacity [W]: 2(4)x21W+0...5
• Number of pins: 3
• Voltage [V]: 12
• Registration Type: ECE approved
• Temperature range from [°C]: -40
• Temperature range to [°C]: 70
• Assy./disassy. by qualified personnel required!:
• Name: HE 4DB003750711
• Manufacturer: HELLA

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Voltage [V]: 12
• Number of pins: 6
• Weight [kg]: 0.04
• Fitting Position: Engine Compartment
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Construction Year to: 03.1997
• Length [mm]: 30.5
• Width [mm]: 30.5
• Height [mm]: 57
• Operating Mode: Electric
• Vehicle Equipment: for vehicles without trailer hitch
• Manufacturer: BOSCH

• Mounting Type: mounting
• Operating Mode: Electronic
• Switching Capacity [W]: 2+1(6)x21W+5 EP
• Number of pins: 4
• Voltage [V]: 12
• Supplementary Article/Info 2: for trailer
• Supplementary Article/Supplementary Info: with holder
• Registration Type: ECE approved
• Temperature range from [°C]: -40
• Temperature range to [°C]: 85
• Assy./disassy. by qualified personnel required!:
• Manufacturer: HELLA

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Voltage [V]: 12
• Weight [kg]: 0.038
• Fitting Position: Engine Compartment
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Supplementary Article/Supplementary Info: without holder
• Voltage [V]: 12
• Temperature range from [°C]: -30
• Temperature range to [°C]: +85
• Number of pins: 6
• Assy./disassy. by qualified personnel required!:
• Name: HE 5WG003620097
• Manufacturer: HELLA

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Supplementary Article/Supplementary Info: without holder
• Voltage [V]: 12
• Temperature range from [°C]: -30
• Temperature range to [°C]: +85
• Number of pins: 6
• Assy./disassy. by qualified personnel required!:
• Name: HE 5WG003620091
• Manufacturer: HELLA

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Construction Year to: 03.1997
• Trailer Hitch: for trailer hitch
• Operating Mode: Electric
• Manufacturer: BOSCH