• Pressure [bar]: 0.4
• Pressure from [bar]: 0.35
• Pressure to [bar]: 0.45
• Combi Switch Function: Normally Closed Contact
• Colour: blue
• Spanner Size: 24
• Thread Size: M10 x 1
• Number of pins: 1
• Manufacturer: JP GROUP
• Lisainfo: PAKENDIS 10 tk
• Additional information: PAKENDIS 10 tk

• Switch point from [bar]: 0.3
• Switch point to [bar]: 0.55
• Length [mm]: 51
• Inner Diameter [mm]: 3.1
• External Thread [mm]: M10 x 1
• Thread Length [mm]: 13
• Spanner Size: 24
• Number of connectors: 1
• Colour Coding: blue
• Lisainfo: Oil pressure switch, 0.3-0.55 Bar
• Additional information: Oil pressure switch, 0.3-0.55 Bar

• Number of pins: 2
• Colour Coding: grey
• Manufacturer: JP GROUP A/S
• Lisainfo: Temperature sensor for cooling system, 2 pins
• Additional information: Temperature sensor for cooling system, 2 pins

• Number of pins: 2
• Housing Colour: light blue
• Connector Shape: oval
• Manufacturer: JP GROUP
• Lisainfo: Sender Unit, coolant temperature
• Additional information: Sender Unit, coolant temperature

• Connector Shape: round
• Operating Mode: Hydraulic
• Thread Size: M 10
• Thread Pitch [mm]: 1
• Number of pins: 1
• Switch point from [bar]: 0.3
• Switch point to [bar]: 0.55
• Supplementary Article/Info 2: with seal ring
• Manufacturer: TOPRAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Length [mm]: 61
• Spanner Size: 19
• Manufacturer: KAMOKA

• Engine Code: Z 12 XE
• Pressure [bar]: 0.5
• Spanner Size: 24
• Number of pins: 1
• Manufacturer: KAVO

• Fabrication Number: ECT-CH-006
• Manufacturer: NTY

• Engine Code: Z 12 XE
• Colour: black
• Pressure to [bar]: 0.55
• Pressure from [bar]: 0.3
• Pressure [bar]: 0.5
• Thread Size: M10x1
• Spanner Size: 24
• Name: EP 1.800.141
• Manufacturer: EPS

• Engine Code: Z 12 XE
• Colour: black
• Pressure to [bar]: 0.55
• Pressure from [bar]: 0.3
• Pressure [bar]: 0.5
• Thread Size: M10x1
• Spanner Size: 24
• Manufacturer: FACET

• Manufacturer Restriction: BOSCH
• Number of pins: 2
• for OE number: 1338467;90541937
• Manufacturer: DELLO AUTOMEGA

• Thread Size: M 10x1
• Housing Colour: black
• Manufacturer: FAE ELEKTRYKA
• Additional information: FE12436
• Lisainfo: FE12436

• Switch Pressure [bar]: 0.5
• Thread Size: M10x1.0
• Sensor Type: Closed-type Sensor
• Manufacturer: VERNET

• Pressure [bar]: 5.5
• Housing Colour: blue
• Thread Size: M10×1.6
• Diameter [mm]: 24
• Spanner Size: 24
• Number of pins: 1
• Manufacturer: DELPHI
• Name: DE SW90015
• Quality class: PJ

Additional information: "Tootja: DELPHI
(kvaliteediklass: PJ)" Lisainfo: "Tootja: DELPHI
(kvaliteediklass: PJ)"

• Thread Size: M12x1.5
• Spanner Size: 19
• Manufacturer: FAST

• Pressure [bar]: 0.4
• Thread Size: M10 x 1
• Number of pins: 1
• Technical Information Number: circuit N.C.
• Manufacturer: ERA

• old version:
• Length [mm]: 51
• Switch point from [bar]: 0.3
• Switch point to [bar]: 0.55
• Inner Diameter [mm]: 3.1
• External Thread Size: M10 x 1
• Thread Length [mm]: 13
• Spanner Size: 24
• Number of connectors: 1
• Colour Coding: blue
• Surface: Zinc-coated
• Weight [kg]: 0.027
• Supplementary Article/Info 2: with seal ring
• Manufacturer: FEBI

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Number of pins: 2
• Sensor Type: Inductive Sensor
• Model Year from: 2007
• Assy./disassy. by qualified personnel required!:
• Manufacturer: ABAKUS

General Information: The following information is for general and informational purposes only and does not constitute warranty terms. Warranty terms and conditions are available from our dealers and in our general terms and conditions of sale. Abakus spare/repair parts are intended only for vehicle repairs in order to restore their original functionality. Abakus spare/repair parts are used or sold to users only for the purpose of repairing vehicles to restore their original look and functionality and are not original/genuine/OE/OEM/OES replacement parts. These items do not originate from the vehicle manufacturer and may be the subject of a design not owned by Abakus and the manufacturer of this spare part. They may only be used for repairs to restore the intended vehicle to its original appearance. Our products are delivered without instruction of installation. Installation of our product may only be carried out by trained specialist technicians in specific car repairs. Products supplied by us are exclusively intended for proper and appropriate use. The warranty may become invalid in the event of: improper installation or repair, unsuitable application or use, installation or repair made outside specialist car workshops. Warranty claims are lost if the vehicle is modified and used for motor sports, tuning or similar events (except our tuning parts which are described in TecDoc and on our price list). Warranty application should include complete documentation among others: chassis no., first registration, vehicle mileage, information about LPG installation, fault memory log, pictures, our QC (quality check) code, installation invoice, contact details of the car repair workshop performing the replacement or repair. Warranty application are available in our Client Panel system. Complaints may require supplementing data such as error memory logs. Incomplete documentation may result in rejection of the claim. Any damage caused during transport is not considered quality damage and will be considered on an individual basis. The product is intended for use within the performance limits specified by the manufacturer and should only be used by qualified personnel who have been trained to operate this product. Before each use, the product should be checked for damage or fixing of its parts and not used if any defects or loose parts are found. Failure to follow the manufacturer's guidelines could result in potential product damage or even injury. Wear appropriate protective clothing if necessary when working with the product.

• old version:
• Length [mm]: 51
• Switch point from [bar]: 0.3
• Switch point to [bar]: 0.55
• External Thread Size: M10 x 1
• Thread Length [mm]: 13
• Spanner Size: 24
• Number of connectors: 1
• Colour Coding: blue
• Weight [kg]: 0.04
• Supplementary Article/Info 2: with seal ring
• Manufacturer: BLUEPRINT

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Connector Shape: rectangular
• Thread Pitch [mm]: 1.5
• Colour Coding: grey
• Sensor Type: NTC Sensor
• Thread Size: M 12
• Number of pins: 2
• Supplementary Article/Info 2: with seal ring
• Manufacturer: TOPRAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Length [mm]: 51
• Height [mm]: 54.3
• Thread Size: M10x1
• Spanner Size: 24
• Mounting Type: Bolted
• Supplementary Article/Supplementary Info: with gasket/seal
• Pressure from [bar]: 0.35
• Pressure to [bar]: 0.55
• Number of connectors: 1
• Combi Switch Function: Normally Closed Contact
• Connector Shape: round
• Corresponds to the original part in colour: blue
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Thread Size: M10 x 1
• Spanner Size: 24
• Pressure from [bar]: 0.3
• Pressure to [bar]: 0.55
• Number of pins: 1
• Manufacturer: AIC

General Information: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.

• Pressure [bar]: 0.5
• Thread Size: M10 X 1
• Housing Colour: black
• Supplementary Article/Supplementary Info: with gasket/seal
• Version: Neue Version
• Article number of recommended accessories: 2324051
• Manufacturer: METZGER

• Fabrication Number: ECP-PL-010
• Manufacturer: NTY

• Supplementary Article/Info 2: with seal ring
• Fabrication Number: ECP-CH-017
• Manufacturer: NTY

• Length [mm]: 61
• External Thread Size: M12 x 1,5
• Spanner Size: 19
• Number of connectors: 2
• Colour: grey
• Screw length below head [mm]: 28
• Weight [kg]: 0.023
• Supplementary Article/Info 2: with seal ring
• Manufacturer: FEBI BILSTEIN

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Thread Size: M12x1.5
• Manufacturer: VERNET

• Anduritüüp: NTC-andur
• Montaaživiis: kruvitud
• Pistikukatte kuju: ovaalne
• Pistikkontaktide arv: 2
• Võtmekaugus: 19
• Keermemõõt: M12x1.5
• OE-numbri jaoks: 46462179
• Piirangutega toode/piirangu info 2: koos rõngastihendiga
• Manufacturer: NRF
• Additional information: 727005 NRF
• Lisainfo: 727005 NRF

• Construction Year to: 09.2003
• Number of pins: 2
• Socket colour: bright blue
• Connector Shape: oval
• Thread Size: M 12x1,5
• Spanner Size: 19 mm
• for OE number: 46469865
• Manufacturer: MEAT&DORIA

• new version:
• Switch point from [bar]: 0.3
• Switch point to [bar]: 0.55
• External Thread Size: M10 x 1
• Spanner Size: 22
• Number of connectors: 1
• Colour: blue
• Surface: Zinc-coated
• Weight [kg]: 0.03
• Supplementary Article/Info 2: with seal ring
• Manufacturer: FEBI BILSTEIN

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Cable Length [mm]: 150
• Weight [kg]: 0.01
• Guarantee: 3 years guarantee
• Cable Cross Section [mm²]: 0.75
• Always compare old and new part (in particular OE No.):
• Name: CE 53SKV283
• Manufacturer: ESEN SKV

• Length [mm]: 61
• External Thread Size: M12 x 1,5
• Spanner Size: 19
• Number of connectors: 2
• Colour: grey
• Screw length below head [mm]: 28
• Weight [kg]: 0.03
• Supplementary Article/Info 2: with seal ring
• Name: SW 40 92 8381
• Manufacturer: SWAG

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Pistikukatte kuju: ovaalne
• Materjal: Plastik
• Pistikkontaktide arv: 2
• Pistikute teostus: Female
• Anduritüüp: NTC-andur
• Võtmekaugus: S19
• Keermemõõt: M12*1,5
• Manufacturer: NISSENS
• Name: NI 207019

Tehniline informatsioon: FIRST FIT - a time-saving installation! Find all additional parts such as O-rings, clip, washer in the box.

• Switch Pressure [bar]: 2
• Thread Size: M10x1.0
• Sensor Type: Closed-type Sensor
• Manufacturer: VERNET

• Number of pins: 2
• Manufacturer: DELLO AUTOMEGA

• for OE number: 9118368
• Sensor Type: Passive sensor
• Manufacturer: KAMOKA

• Construction Year to: 03.2004
• Housing Colour: blue
• Number of pins: 2
• Thread Size: M12X1.5-6g
• Spanner Size: 19
• Manufacturer: DELPHI
• Name: DE TS10253

• Fabrication Number: ESS-FT-002
• Manufacturer: NTY

• new version:
• Switch point from [bar]: 0.3
• Switch point to [bar]: 0.55
• External Thread Size: M10 x 1
• Spanner Size: 22
• Number of connectors: 1
• Colour: blue
• Surface: Zinc-coated
• Weight [kg]: 0.03
• Supplementary Article/Info 2: with seal ring
• Name: SW 40 92 7223
• Manufacturer: SWAG

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Operating voltage [V]: 12
• Sensor Type: Passive sensor
• Resistor [Ohm]: 900
• Fitting Depth [mm]: 34.5
• Supplementary Article/Info 2: with seal ring, without cable
• Number of pins: 2
• Manufacturer: JP GROUP A/S
• Lisainfo: Sensor, crankshaft pulse
• Additional information: Sensor, crankshaft pulse

• Connector Shape: oval
• Number of pins: 2
• Supplementary Article/Info 2: without cable
• Manufacturer: TOPRAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Supplementary Article/Info 2: without cable
• Number of pins: 2
• for OE number: 9947855
• Sensor Type: Inductive Sensor
• Assy./disassy. by qualified personnel required!:
• Manufacturer: ABAKUS LORO

General Information: The following information is for general and informational purposes only and does not constitute warranty terms. Warranty terms and conditions are available from our dealers and in our general terms and conditions of sale. Abakus spare/repair parts are intended only for vehicle repairs in order to restore their original functionality. Abakus spare/repair parts are used or sold to users only for the purpose of repairing vehicles to restore their original look and functionality and are not original/genuine/OE/OEM/OES replacement parts. These items do not originate from the vehicle manufacturer and may be the subject of a design not owned by Abakus and the manufacturer of this spare part. They may only be used for repairs to restore the intended vehicle to its original appearance. Our products are delivered without instruction of installation. Installation of our product may only be carried out by trained specialist technicians in specific car repairs. Products supplied by us are exclusively intended for proper and appropriate use. The warranty may become invalid in the event of: improper installation or repair, unsuitable application or use, installation or repair made outside specialist car workshops. Warranty claims are lost if the vehicle is modified and used for motor sports, tuning or similar events (except our tuning parts which are described in TecDoc and on our price list). Warranty application should include complete documentation among others: chassis no., first registration, vehicle mileage, information about LPG installation, fault memory log, pictures, our QC (quality check) code, installation invoice, contact details of the car repair workshop performing the replacement or repair. Warranty application are available in our Client Panel system. Complaints may require supplementing data such as error memory logs. Incomplete documentation may result in rejection of the claim. Any damage caused during transport is not considered quality damage and will be considered on an individual basis. The product is intended for use within the performance limits specified by the manufacturer and should only be used by qualified personnel who have been trained to operate this product. Before each use, the product should be checked for damage or fixing of its parts and not used if any defects or loose parts are found. Failure to follow the manufacturer's guidelines could result in potential product damage or even injury. Wear appropriate protective clothing if necessary when working with the product.

• Engine Code: Z 12 XE
• Colour: black
• Thread Size: M12x1,5
• Spanner Size: 19
• Corresponds to the original part in colour: white, green, black
• for article number: 1.880.170, 1.880.190
• Name: EP 1.830.239
• Manufacturer: EPS

• Engine Code: Z 12 XE
• Colour: black
• Thread Size: M12x1,5
• Spanner Size: 19
• Corresponds to the original part in colour: white, green, black
• for article number: 7.8170, 7.8190
• Manufacturer: FACET

• Number of pins: 2
• Thread Size: M12x1,5
• Supplementary Article/Info 2: with seal ring
• Housing Colour: black
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Voltage [V]: 12
• Supplementary Article/Info 2: without cable
• Number of pins: 2
• Sensor Type: Inductive Sensor
• Assy./disassy. by qualified personnel required!:
• Manufacturer: ABAKUS LORO

General Information: The following information is for general and informational purposes only and does not constitute warranty terms. Warranty terms and conditions are available from our dealers and in our general terms and conditions of sale. Abakus spare/repair parts are intended only for vehicle repairs in order to restore their original functionality. Abakus spare/repair parts are used or sold to users only for the purpose of repairing vehicles to restore their original look and functionality and are not original/genuine/OE/OEM/OES replacement parts. These items do not originate from the vehicle manufacturer and may be the subject of a design not owned by Abakus and the manufacturer of this spare part. They may only be used for repairs to restore the intended vehicle to its original appearance. Our products are delivered without instruction of installation. Installation of our product may only be carried out by trained specialist technicians in specific car repairs. Products supplied by us are exclusively intended for proper and appropriate use. The warranty may become invalid in the event of: improper installation or repair, unsuitable application or use, installation or repair made outside specialist car workshops. Warranty claims are lost if the vehicle is modified and used for motor sports, tuning or similar events (except our tuning parts which are described in TecDoc and on our price list). Warranty application should include complete documentation among others: chassis no., first registration, vehicle mileage, information about LPG installation, fault memory log, pictures, our QC (quality check) code, installation invoice, contact details of the car repair workshop performing the replacement or repair. Warranty application are available in our Client Panel system. Complaints may require supplementing data such as error memory logs. Incomplete documentation may result in rejection of the claim. Any damage caused during transport is not considered quality damage and will be considered on an individual basis. The product is intended for use within the performance limits specified by the manufacturer and should only be used by qualified personnel who have been trained to operate this product. Before each use, the product should be checked for damage or fixing of its parts and not used if any defects or loose parts are found. Failure to follow the manufacturer's guidelines could result in potential product damage or even injury. Wear appropriate protective clothing if necessary when working with the product.

• Outer Diameter [mm]: 7.4
• Resistor [Ohm]: 2,080, 294
• Supplementary Article/Supplementary Info: with gasket/seal
• External Thread [mm]: 12
• Thread Pitch [mm]: 1.5
• Temperature range [°C]: 25, 80
• Mounting Type: Bolted
• Colour: blue
• Spanner Size: 19
• Sensor Type: NTC Sensor
• Number of pins: 2
• Corresponds to the original part in colour: black, white, light blue
• Assy./disassy. by qualified personnel required!:
• Manufacturer: HELLA
• Name: HE 6PT009107611

Brief Information: *** HELLA Electronics OE competence for over 60 years.

Manufacturer: NRF KLIMATYZACJA

• Tightening torque from [Nm]: 20
• Voltage [V]: 12
• Combi Switch Function: Normally Closed Contact
• Current Strength [A]: 0.25
• Tolerance [%]: 15
• Thread Size: M10x1
• Spanner Size: 24
• Pressure from [bar]: 0.35
• Pressure to [bar]: 0.55
• Number of pins: 1
• Corresponds to the original part in colour: blue
• Assy./disassy. by qualified personnel required!:
• SVHC: 7439-92-1; Lead
• Name: HE 6ZL008780011
• Manufacturer: HELLA

• Thread Size: M12 x 1,5
• Number of pins: 2
• Manufacturer: ERA

• Required quantity: 1
• Number of pins: 2
• Sensor Type: Inductive Sensor
• Supplementary Article/Info 2: without cable
• Housing Colour: black
• Manufacturer: BREMI

• Height [mm]: 34.5
• Resistor [Ohm]: 970
• Number of connectors: 2
• Manufacturer: VERNET

• Number of pins: 2
• Colour Coding: grey
• Packaging length [cm]: 3.5
• Packaging width [cm]: 6
• Packaging height [cm]: 3.5
• Weight [kg]: 0.026
• for OE number: 1338467, 1338C7, 90541937
• Manufacturer: AKSDASIS

• Voltage [V]: 12
• Supplementary Article/Supplementary Info: without cable pull
• Number of pins: 2
• Guarantee: 3 years guarantee
• Weight [kg]: 0.05
• Operating Mode: Electric
• Always compare old and new part (in particular OE No.):
• Name: CE 17SKV228
• Manufacturer: ESEN SKV

• Supplementary Article/Supplementary Info: with gasket/seal
• Thread Size: M12 x 1,5
• Spanner Size: 19
• Number of pins: 2
• Manufacturer: AIC

General Information: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.

• Number of pins: 2
• Weight [kg]: 0.3
• Packaging length [cm]: 12
• Packaging width [cm]: 8
• Packaging height [cm]: 6

• Number of pins: 2
• Manufacturer: FAE

• Construction Year to: 02.2004
• Engine Code: Z 12 XE
• Sensor Type: Inductive Sensor
• Number of pins: 2
• Voltage [V]: 12
• Connector Shape: oval
• Supplementary Article/Info 2: without cable
• Resistor [Ohm]: 970
• Manufacturer: VALEO
• Name: VA 254000

Manufacturer: MAGNETI MARELLI

• Engine Code: Z 12 XE
• Name: EP 1.953.235
• Manufacturer: EPS

• Number of pins: 3
• for OE number: 6238110
• Sensor Type: Hall Sensor
• Assy./disassy. by qualified personnel required!:
• Manufacturer: ABAKUS

General Information: The following information is for general and informational purposes only and does not constitute warranty terms. Warranty terms and conditions are available from our dealers and in our general terms and conditions of sale. Abakus spare/repair parts are intended only for vehicle repairs in order to restore their original functionality. Abakus spare/repair parts are used or sold to users only for the purpose of repairing vehicles to restore their original look and functionality and are not original/genuine/OE/OEM/OES replacement parts. These items do not originate from the vehicle manufacturer and may be the subject of a design not owned by Abakus and the manufacturer of this spare part. They may only be used for repairs to restore the intended vehicle to its original appearance. Our products are delivered without instruction of installation. Installation of our product may only be carried out by trained specialist technicians in specific car repairs. Products supplied by us are exclusively intended for proper and appropriate use. The warranty may become invalid in the event of: improper installation or repair, unsuitable application or use, installation or repair made outside specialist car workshops. Warranty claims are lost if the vehicle is modified and used for motor sports, tuning or similar events (except our tuning parts which are described in TecDoc and on our price list). Warranty application should include complete documentation among others: chassis no., first registration, vehicle mileage, information about LPG installation, fault memory log, pictures, our QC (quality check) code, installation invoice, contact details of the car repair workshop performing the replacement or repair. Warranty application are available in our Client Panel system. Complaints may require supplementing data such as error memory logs. Incomplete documentation may result in rejection of the claim. Any damage caused during transport is not considered quality damage and will be considered on an individual basis. The product is intended for use within the performance limits specified by the manufacturer and should only be used by qualified personnel who have been trained to operate this product. Before each use, the product should be checked for damage or fixing of its parts and not used if any defects or loose parts are found. Failure to follow the manufacturer's guidelines could result in potential product damage or even injury. Wear appropriate protective clothing if necessary when working with the product.

• Engine Code: Z 12 XE
• Manufacturer: FACET

• Number of mounting bores: 1
• Resistor [Ohm]: 970
• Tolerance [%]: 10
• Sensor Type: Inductive Sensor
• Supplementary Article/Supplementary Info: with gasket/seal
• Number of pins: 2
• Supplementary Article/Info 2: without cable
• Assy./disassy. by qualified personnel required!:
• Manufacturer: HELLA

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Number of pins: 2
• Manufacturer: DELPHI LOCKHEED HAMULCE
• Name: DE SS10805

Additional information: "Tootja: DELPHI
CORSA B (73/, 78/, 7
(kvaliteediklass: PJ)" Lisainfo: "Tootja: DELPHI
CORSA B (73/, 78/, 7
(kvaliteediklass: PJ)"

• Length [mm]: 38
• Width [mm]: 67
• Height [mm]: 34
• Number of connectors: 2
• Required quantity: 1
• Resistor [Ohm]: 920
• Colour: black
• Operating Mode: Electric
• Sensor Type: Passive sensor, Inductive Sensor
• Number of pins: 2
• Rated Voltage [V]: 12
• Fitting Depth [mm]: 34.5
• Supplementary Article/Info 2: with seal ring, without cable
• Connector Shape: oval
• Number of mounting bores: 1
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Length [mm]: 51
• Number of connectors: 2
• Weight [kg]: 0.065
• Supplementary Article/Info 2: with seal ring
• Manufacturer: FEBI BILSTEIN

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Fitting Position: Front, before catalytic converter
• Oxygen Sensor: Regulating Sensor, Thread pre-greased
• Fabrication Number: ESL-PL-000
• Manufacturer: NTY

Manufacturer: DELLO AUTOMEGA

• Manufacturer: JP GROUP
• Lisainfo: Sensor, camshaft position
• Additional information: Sensor, camshaft position

• Engine Code: Z 12 XE
• Name: EP 1.957.006
• Manufacturer: EPS

• Connector Shape: oval
• Number of pins: 3
• Supplementary Article/Info 2: without cable
• Manufacturer: TOPRAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Number of connectors: 2
• Weight [kg]: 0.001
• Supplementary Article/Info 2: with seal ring
• Manufacturer: BLUEPRINT

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Engine Code: Z 12 XE
• Manufacturer: FACET

• Alternatively:
• Number of pins: 2
• Alternative Repair Kit: 550305
• Manufacturer: ERA

• Construction Year to: 09.2003
• Manufacturer: BOSCH

• Length [mm]: 51
• Number of connectors: 2
• Weight [kg]: 0.065
• Supplementary Article/Info 2: with seal ring
• Name: SW 40 92 4616
• Manufacturer: SWAG

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Overall Length [mm]: 549
• Number of circuits: 4
• Oxygen Sensor: Thread pre-greased
• Fabrication Number: ESL-PL-013
• Manufacturer: NTY

• Pinge [V]: 12
• Pistikkontaktide arv: 2
• Väändejõud [Nm]: 20
• Piirangutega toode/piirangu info 2: ilma kaablita
• Vastab originaalosa värvile: must
• Pistikute teostus: Lamepistik
• Pistikukatte kuju: ristkülik
• Monteerimist/demonteerimist peab tegema spetsialist!:
• Manufacturer: HELLA
• Name: HE 6PG013114441

Lühiinformatsioon: *** HELLA Electronics OE competence for over 60 years.

• Housing Type: with housing
• Fabrication Number: EPP-PL-003
• Manufacturer: NTY

• Number of circuits: 3
• Version: mit Stoßverbinder
• Cable Length [mm]: 250
• Wire cross-section [mm²]: 0,75
• Manufacturer: METZGER