• Operating voltage [V]: 12
• Sensor Type: NTC Sensor
• Switch Point [°C]: 150
• Supplementary Article/Info 2: with seal ring
• Number of pins: 2
• Manufacturer: JP GROUP
• Lisainfo: Sender for water temperature, 2 pins
• Additional information: Sender for water temperature, 2 pins

• Spring Type: for vehicles with air suspension
• Vehicle Identification Number (VIN) to: A 372602
• Construction Year to: 08.2002
• Operating voltage [V]: 12
• Sensor Type: NTC Sensor
• Thread Size: M14 x 1,5
• Spanner Size: 19
• Manufacturer: JP GROUP
• Lisainfo: Coolant Temperature Sensor
• Additional information: Coolant Temperature Sensor

• Fabrication Number: ECT-ME-002
• Manufacturer: NTY
• Name: NTY ECT-ME-002

• Spanner Size: 19
• for OE number: K05103534AA
• Manufacturer: KAMOKA

• Number of pins: 2
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: MAX

• Thread Size: 9 mm
• Manufacturer: VERNET
• Additional information: WS2698
• Lisainfo: WS2698

• for OE number: 099 905 3800
• Manufacturer: TRUCKTEC

• Instruments: with water temperature gauge
• Sensor Type: NTC Sensor
• Mounting Type: Bolted
• Connector Shape: oval
• Number of pins: 2
• Socket colour: black
• Spanner Size: 19
• Thread Size: M14x1.5
• for OE number: 0005426218
• Supplementary Article/Info 2: with seal ring
• Name: Andur,Jahutusvedeliku temp.
• Manufacturer: NRF

• Number of pins: 2
• Length [mm]: 88
• Height [mm]: 89.5
• Weight [kg]: 0.1
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Sensor Type: NTC Sensor
• Mounting Type: Clamped
• Connector Shape: oval
• Number of pins: 2
• Socket colour: black
• for OE number: 5080147AA
• Supplementary Article/Info 2: with seal ring
• Name: Andur,Jahutusvedeliku temp.
• Manufacturer: NRF

Manufacturer: FAST

Manufacturer: FAST

• for OE number: 003 153 28 28
• Fabrication Number: ECP-CH-020
• Manufacturer: NTY

• Fabrication Number: ECP-ME-001
• Manufacturer: NTY

• Sensor Type: Inductive Sensor
• Number of pins: 2
• Component Number: 120-04-027
• Manufacturer: ABAKUS DEPO/LORO

General Information: The following information is for general and informational purposes only and does not constitute warranty terms. Warranty terms and conditions are available from our dealers and in our general terms and conditions of sale. Abakus spare/repair parts are intended only for vehicle repairs in order to restore their original functionality. Abakus spare/repair parts are used or sold to users only for the purpose of repairing vehicles to restore their original look and functionality and are not original/genuine/OE/OEM/OES replacement parts. Our products are delivered without instruction of installation. Installation of our product may only be carried out by trained specialist technicians in specific car repairs. Products supplied by us are exclusively intended for proper and appropriate use. The warranty may become invalid in the event of: improper installation or repair, unsuitable application or use, installation or repair made outside specialist car workshops. Warranty claims are lost if the vehicle is modified and used for motor sports, tuning or similar events (except our tuning parts which are described in TecDoc and on our price list). Warranty application should include complete documentation among others: chassis no., first registration, vehicle mileage, information about LPG installation, fault memory log, pictures, our QC (quality check) code, installation invoice, contact details of the car repair workshop performing the replacement or repair. Warranty application are available in our Client Panel system. Complaints may require supplementing data such as error memory logs. Incomplete documentation may result in rejection of the claim. Any damage caused during transport is not considered quality damage and will be considered on an individual basis.

• Number of pins: 2
• Manufacturer: ERA

• Sensor Type: Passive sensor
• for OE number: 05080352AA
• Manufacturer: KAMOKA

• Engine Code: M 137.970
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: EPS

for article number: 1.880.588, 1.880.589, 1.880.590, 1.880.591, 1.880.592, 1.880.593, 1.880.594, 1.880.595, 1.880.596, 1.880.597, 1.880.598, 1.880.784, 1.880.847, 1.880.935

• Number of connectors: 2
• Colour: black
• Weight [kg]: 0.015
• for OE number: 099 905 38 00
• Supplementary Article/Info 2: with seal ring
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: FEB

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Spanner Size: 19 mm
• Sensor Type: NTC Sensor
• Number of pins: 2
• Connecting thread: M14 x 1,5
• Manufacturer: ERA

• Spring Type: for vehicles with air suspension
• Vehicle Identification Number (VIN) to: A 372602
• Construction Year to: 08.2002
• Height [mm]: 50.6
• Weight [kg]: 0.027
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Sensor Type: Hall Sensor
• Number of pins: 3
• Manufacturer: ABAKUS DEPO/LORO

General Information: The following information is for general and informational purposes only and does not constitute warranty terms. Warranty terms and conditions are available from our dealers and in our general terms and conditions of sale. Abakus spare/repair parts are intended only for vehicle repairs in order to restore their original functionality. Abakus spare/repair parts are used or sold to users only for the purpose of repairing vehicles to restore their original look and functionality and are not original/genuine/OE/OEM/OES replacement parts. Our products are delivered without instruction of installation. Installation of our product may only be carried out by trained specialist technicians in specific car repairs. Products supplied by us are exclusively intended for proper and appropriate use. The warranty may become invalid in the event of: improper installation or repair, unsuitable application or use, installation or repair made outside specialist car workshops. Warranty claims are lost if the vehicle is modified and used for motor sports, tuning or similar events (except our tuning parts which are described in TecDoc and on our price list). Warranty application should include complete documentation among others: chassis no., first registration, vehicle mileage, information about LPG installation, fault memory log, pictures, our QC (quality check) code, installation invoice, contact details of the car repair workshop performing the replacement or repair. Warranty application are available in our Client Panel system. Complaints may require supplementing data such as error memory logs. Incomplete documentation may result in rejection of the claim. Any damage caused during transport is not considered quality damage and will be considered on an individual basis.

• Number of connectors: 2
• Colour: black
• Weight [kg]: 0.015
• Supplementary Article/Info 2: with seal ring
• for OE number: 099 905 38 00
• Name: SW 10 93 4074
• Manufacturer: SWAG

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Thread Size: M 14x1,5
• Number of pins: 2
• Colour: black
• Supplementary Article/Supplementary Info: with seal
• Power [W]: 0.06
• Manufacturer: METZGER

Manufacturer: FAE

• Instruments: with water temperature gauge
• Thread Size: M14x1.5
• Number of connectors: 2
• Manufacturer: VERNET

• Fabrication Number: ESS-ME-000
• Manufacturer: NTY

• Engine Code: M 137.970
• Instruments: with water temperature gauge
• Housing Colour: black
• Thread Size: M14x1,5
• Spanner Size: 19
• Name: ANDUR, KšTUSETEMPERATUUR
• Manufacturer: EPS

• Sensor Type: NTC Sensor
• Supplementary Article/Info 2: with seal ring
• Number of pins: 2
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: MEY

• Height [mm]: 18.2
• Supplementary Article/Supplementary Info: with seal
• Number of pins: 2
• Weight [kg]: 0.021
• Manufacturer: VEMO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Required quantity: 1
• Number of pins: 2
• Sensor Type: Inductive Sensor
• Supplementary Article/Info 2: without cable
• Housing Colour: black
• Manufacturer: BREMI

• Voltage [V]: 12
• Supplementary Article/Supplementary Info: without cable pull
• Number of pins: 2
• Weight [kg]: 0.04
• Operating Mode: Electric
• Warranty: 3 years warranty
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY
• Name: CE 17SKV330

• Sensor Type: Passive sensor
• Supplementary Article/Info 2: without cable
• Voltage [V]: 12
• Name: ANDUR, VŽNTVOLL
• Manufacturer: MAX

• for OE number: 003 153 8628
• Manufacturer: TRUCKTEC

• Height [mm]: 40
• Resistor [Ohm]: 1,150
• Number of connectors: 2
• Manufacturer: VERNET

• Engine Code: M 137.970
• Name: EP 1.953.578
• Manufacturer: EPS

• Number of pins: 2
• Connector Shape: D Shape
• Sensor Type: Inductive Sensor
• Supplementary Article/Info 2: without cable
• Quality: OE EQUIVALENT
• Name: Andur, v„ntvoll
• Manufacturer: MD

• Sensor Type: Inductive Sensor
• Number of pins: 2

• Number of pins: 2
• Name: ANDUR, VŽNTVOLL
• Manufacturer: DLP

• Fitting Position: Flywheel side
• Sensor Type: Inductive Sensor, Passive sensor
• Number of connectors: 2
• Supplementary Article/Info 2: for crankshaft, without cable
• Required quantity: 1
• Resistor [Ohm]: 680
• Alternatively:
• Colour: black
• Operating Mode: Electric
• Mounting Type: Bolted
• Number of pins: 2
• Rated Voltage [V]: 12
• Fitting Depth [mm]: 40
• Connector Shape: D Shape
• Number of mounting bores: 1
• Weight [kg]: 0.029
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Length [mm]: 40
• Alternatively:
• Number of pins: 2
• Supplementary Article/Info 2: without cable
• Alternative Repair Kit: 550275
• Resistor [kOhm]: 1
• Manufacturer: ERA

• Colour: black
• Sensor Type: Passive sensor, Inductive Sensor
• Number of pins: 2
• Supplementary Article/Info 2: without cable
• Connector Shape: D Shape
• Required quantity: 1
• Mounting Type: Bolted
• Manufacturer: FAST

• Number of pins: 3
• Weight [kg]: 0.04
• Warranty: 3 years warranty
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY
• Name: CE 17SKV496

• Length [mm]: 76
• Number of connectors: 2
• Weight [kg]: 0.031
• Observe service information:
• Manufacturer: FEBI BILSTEIN

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Required quantity: 1
• Number of pins: 3
• Sensor Type: Inductive Sensor
• Supplementary Article/Info 2: without cable
• Housing Colour: grey
• Manufacturer: BREMI

• Number of mounting bores: 1
• Sensor Type: Inductive Sensor
• Number of pins: 2
• Mounting Type: Bolted
• Assy./disassy. by qualified personnel required!:
• Name: ANDUR, VŽNTVOLL
• Manufacturer: HEL

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Number of pins: 2
• Manufacturer: FAE

• Sensor Type: Inductive Sensor
• Number of pins: 2
• Name: ANDUR, VŽNTVOLL
• Manufacturer: MEY

• Number of circuits: 4
• Lambda Sensor: Regulating Probe
• Manufacturer: KAMOKA

• Name: ANDUR, VŽNTVOLL
• Manufacturer: BOS

• Construction Year to: 09.2004
• Engine Code: 137.970
• Sensor Type: Inductive Sensor
• Number of pins: 2
• Voltage [V]: 12
• Connector Shape: D Shape
• Supplementary Article/Info 2: without cable
• Resistor [Ohm]: 1,150
• Weight [kg]: 0.03
• Manufacturer: VALEO
• Name: VA 254008

• Fabrication Number: EPP-ME-021
• Number of pins: 5
• Manufacturer: NTY

• Number of pins: 3
• Name: ANDUR,NUKKVOLLIPOSITSIOON
• Manufacturer: DLP

• Length [mm]: 51
• Width [mm]: 50
• Outer Diameter [mm]: 17.8
• Number of connectors: 3
• Weight [kg]: 0.03
• Supplementary Article/Info 2: with seal ring
• Manufacturer: FEBI BILSTEIN

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Lambda Sensor: Diagnostic Probe, Regulating Probe
• Length [mm]: 900
• Fabrication Number: ESL-ME-000
• Manufacturer: NTY

• for OE number: 162 094 31 48
• Manufacturer: KAMOKA

• Length [mm]: 51
• Width [mm]: 50
• Outer Diameter [mm]: 17.8
• Number of connectors: 3
• Weight [kg]: 0.03
• Supplementary Article/Info 2: with seal ring
• Name: SW 10 93 6432
• Manufacturer: SWAG

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Number of pins: 3
• Fitting Depth [mm]: 24
• Name: ANDUR,NUKKVOLLIPOSITSIOON
• Manufacturer: TRI

• Warranty: 5 years warranty
• General Information: Sold in Hueco brand: printing and packaging
• Manufacturer: HUCO

• for OE number: 000 540 7617
• Cable Length [mm]: 500
• Number of pins: 4
• Lambda Sensor: Heated
• Manufacturer: TRUCKTEC AUTOMOTIVE

• Engine Code: M 137.970
• Lambda Sensor: Regulating Probe
• Required quantity: 2
• Number of circuits: 4
• Supplementary Article/Info 2: without plug
• Manufacturer: ENERGY

• Sensor Type: Inductive Sensor
• Number of pins: 2
• Height [mm]: 40
• Quality: IAM
• Manufacturer: METZGER

• Number of pins: 5
• Plug Type: Male
• Voltage [V]: 12
• Quality class: PJ
• Name: Air flow sensor

• Lambda Sensor: Regulating Probe, Diagnostic Probe, Heated
• Required quantity: 4
• Block Separation:
• Fitting Position: before catalytic converter
• Number of circuits: 4
• Connector/Clamp: Connector may need adjustment
• Name: LAMBDA ANDUR
• Manufacturer: MAX
• Lisainfo: MGS-615
• Additional information: MGS-615

• Lambda Sensor: Diagnostic Probe, Regulating Probe
• Voltage [V]: 12
• Length [mm]: 480
• Number of circuits: 4
• Weight [kg]: 0.1
• Operating Mode: Electric
• Warranty: 3 years warranty
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY
• Name: CE 09SKV057

Exhaust System: after catalytic converter, before catalytic converter

• Lambda Sensor: Diagnostic Probe, Heated
• External Thread Size: M18 x 1,5
• Spanner Size: 22
• Number of circuits: 4
• Cable Length [mm]: 400
• Weight [kg]: 0.082
• Name: SW 33 10 3189
• Manufacturer: SWAG

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Voltage [V]: 12
• Name: OHUMASSIMOOTJA
• Manufacturer: MAX

• Voltage [V]: 12
• Corresponds to the original part in colour: grey
• Sensor Type: Hall Sensor
• Supplementary Article/Supplementary Info: with seal
• Number of pins: 3
• Supplementary Article/Info 2: without cable
• Assy./disassy. by qualified personnel required!:
• Name: HE 6PU009121711
• Manufacturer: HELLA

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Lambda Sensor: Diagnostic Probe, Planar probe
• Required quantity: 4
• Number of pins: 4
• Cable Length [mm]: 800
• Manufacturer: MEAT&DORIA

• Lambda Sensor: Lambda Sensor
• Voltage [V]: 12
• Length [mm]: 660
• Number of circuits: 4
• Weight [kg]: 0.14
• Resistor [Ohm]: 9
• Operating Mode: Electric
• Warranty: 3 years warranty
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY
• Name: CE 09SKV643

• Engine Code: M 137.970
• Fitting Position: after catalytic converter
• Cable Length [mm]: 400
• Conductor Number: 4
• Available as universal article as well, see article no.: 1.998.240
• Number of circuits: 4
• Name: LAMBDA ANDUR
• Manufacturer: EPS

Lambda Sensor: Diagnostic Probe, Heated, Planar probe, Thread pre-greased

• Lambda Sensor: Diagnostic Probe, Planar probe, Heated
• Quantity: 4
• Cable Length [mm]: 380
• Name: LAMBDA ANDUR
• Manufacturer: DLP

• Voltage [V]: 12
• Housing Type: with housing
• Number of pins: 5
• Weight [kg]: 0.32
• Operating Mode: Electric
• Warranty: 3 years warranty
• Always compare old and new part (in particular OE No.):
• Manufacturer: ESEN SKV

• Lambda Sensor: Regulating Probe, Diagnostic Probe
• Required quantity: 4
• Block Separation:
• Number of circuits: 4
• Recommended change interval [km]: 160,000
• Connector/Clamp: Connector may need adjustment
• Name: LAMBDA ANDUR
• Manufacturer: BOS

Fitting Position: before catalytic converter, after catalytic converter

• Fitting Position: Left
• Vehicle Identification Number (VIN) from: A087201
• Exhaust System: for pre-catalytic converter
• Quality: OE
• Manufacturer Restriction: DENSO
• Thread Size: M18x1.5
• Cable Length [mm]: 750
• Number of pins: 4
• Weight [g]: 93
• Gross Weight [g]: 140
• Manufacturer: DENSO
• Name: DN DOX-0150
• Quality class: Q

Lambda Sensor: Regulating Probe, Heated, Planar probe, Thread pre-greased, Lambda Sensor Additional information: "Tootja: DENSO
(kvaliteediklass: Q)" Lisainfo: "Tootja: DENSO
(kvaliteediklass: Q)"

• Lambda Sensor: Regulating Probe, Planar probe, Heated
• Fitting Position: before catalytic converter
• Block Separation:
• Exhaust System: for pre-catalytic converter
• Quantity: 4
• Cable Length [mm]: 470
• Manufacturer: DELPHI
• Name: DE ES20175-12B1
• Quality class: PJ

Additional information: "Tootja: DELPHI
KLASA E (W210), 06.9
(kvaliteediklass: PJ)" Lisainfo: "Tootja: DELPHI
KLASA E (W210), 06.9
(kvaliteediklass: PJ)"

• Lambda Sensor: Diagnostic Probe, Regulating Probe
• Length [mm]: 470
• Number of connectors: 4
• Manufacturer: VERNET

Exhaust System: after catalytic converter, before catalytic converter, Duplex (1 le./1 ri.)

• Warranty: 5 years warranty
• General Information: Sold in Hueco brand: printing and packaging
• Name: OHUMASSIMOOTJA
• Manufacturer: HUC

• Operating Mode: Electric
• Name: OHUMASSIMOOTJA
• Manufacturer: MAG

• Sensor Type: Hall Sensor
• Number of pins: 3
• Housing Colour: grey
• Supplementary Article/Info 2: without cable
• Manufacturer: FAE

• Lambda Sensor: Planar probe
• Thread Size: M18 x 1,5
• Cable Length [mm]: 400
• Number of pins: 4
• Name: Lambda andur
• Manufacturer: MEY

Fitting Position: before catalytic converter, after catalytic converter

• Housing Type: with housing
• Number of pins: 5
• Plug Type: Male
• Housing Colour: black
• Voltage [V]: 12
• Recommended additional repairs: Air Filter
• Manufacturer: DELPHI
• Name: DE AF10296-12B1

• Lambda Sensor: Regulating Probe
• Fitting Position: before catalytic converter
• Required quantity: 4
• Number of circuits: 4
• Overall Length [mm]: 450
• Available as universal article as well, see article no.: 0258986615
• Recommended change interval [km]: 160,000
• Name: LAMBDA ANDUR
• Manufacturer: BOS

• Required quantity: 1
• Voltage [V]: 12
• Number of pins: 5
• Name: OHUMASSIMOOTJA
• Manufacturer: BRM

• Engine Code: M 137.970
• Fitting Position: before catalytic converter
• Cable Length [mm]: 450
• Conductor Number: 4
• Available as universal article as well, see article no.: 1.998.240
• Number of circuits: 4
• Name: LAMBDA ANDUR
• Manufacturer: EPS

Lambda Sensor: Regulating Probe, Heated, Planar probe, Thread pre-greased

• Lambda Sensor: Diagnostic Probe
• Fitting Position: after catalytic converter
• Required quantity: 4
• Number of circuits: 4
• Overall Length [mm]: 400
• Available as universal article as well, see article no.: 0258986615
• Recommended change interval [km]: 160,000
• Name: LAMBDA ANDUR
• Manufacturer: BOS

• Construction Year to: 08.2002
• Recommended additional repairs: Air Filter
• Name: OHUMASSIMOOTJA
• Manufacturer: BOS