• Quantity: 1
• Pressure [bar]: 0.5
• General Information: oil pressure switch；0.5Bar
• Manufacturer: VIKA

• Fabrication Number: ECC-AU-003
• Thread Size: M10x1
• Spanner Size: 24
• Supplementary Article/Info 2: with seal ring
• Socket colour: green
• Number of pins: 1
• Manufacturer: NTY

• Colour Coding: grey
• Number of pins: 2
• Manufacturer: JP GROUP
• Lisainfo: Sender for water temperature gauge, 2 pins
• Additional information: Sender for water temperature gauge, 2 pins

• Connector Shape: D Shape
• Operating Mode: Hydraulic
• Colour Coding: green
• Thread Size: M 10
• Thread Pitch [mm]: 1
• Number of pins: 1
• Control Range [bar]: 0,3 - 0,6
• Supplementary Article/Info 2: with seal ring
• Manufacturer: TOPRAN HANS PRIES

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Colour Coding: grey
• Fabrication Number: ECT-VW-000
• Manufacturer: NTY
• Name: NTY ECT-VW-000

• Pressure [bar]: 0.5
• Thread Size: M 10 x 1
• Manufacturer: MEAT&DORIA

• Connector Shape: oval, D Shape
• Colour Coding: grey
• Sensor Type: NTC Sensor
• Number of pins: 2
• Consult accessories list for recommended additional repairs:
• Manufacturer: TOPRAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Switch Pressure [bar]: 0.5
• Thread Size: M10x1.0
• Sensor Type: Open-style sensor
• Manufacturer: VERNET

• Pressure [bar]: 6
• Housing Colour: green
• Thread Size: M10×1-6g
• Diameter [mm]: 24
• Spanner Size: 24
• Number of pins: 1
• Name: DE SW90024
• Manufacturer: DELPHI
• Lisainfo: SW90024
• Additional information: SW90024

• Sensor Type: NTC Sensor
• Mounting Type: Clamped
• Connector Shape: D Shape
• Number of pins: 2
• for OE number: 06A919501
• Supplementary Article/Info 2: with mounting parts
• Manufacturer: NRF

• Number of connectors: 2
• Manufacturer: 3RG

• Number of pins: 2
• Sensor Type: NTC Sensor
• Connector Shape: D Shape
• Colour: black
• for OE number: 06B905379D
• Manufacturer: DELLO AUTOMEGA

• Pressure [bar]: 0.5
• Thread Size: M10 x 1
• Number of pins: 1
• Technical Information Number: circuit N.O.
• Manufacturer: ERA

• Quantity: 1
• General Information: oil pressure switch
• Manufacturer: BORSEHUNG

• Thread Size: 20 mm
• Number of pins: 2
• Manufacturer: CALORSTAT BY VERNET
• Additional information: WS2607
• Lisainfo: WS2607

• for OE number: 06A 919 501
• Manufacturer: TRUCKTEC AUTOMOTIVE

• Tightening torque from [Nm]: 20
• Voltage [V]: 12
• Combi Switch Function: Normally Open Contact
• Current Strength [A]: 0.15
• Tolerance [%]: 15
• Thread Size: M10x1
• Spanner Size: 24
• Pressure from [bar]: 0.3
• Pressure to [bar]: 0.6
• Number of pins: 1
• Corresponds to the original part in colour: green
• Assy./disassy. by qualified personnel required!:
• Manufacturer: HELLA

• Thread Size: M20
• Number of pins: 2
• Housing Colour: grey
• Connector Shape: oval
• Manufacturer: ERA

• Engine Code: BMY
• Colour: grey
• for article number: 1.660.015K, 1.830.278K, 1.879.946
• Name: EP 1.830.278
• Manufacturer: EPS
• Additional information: 1-830-278
• Lisainfo: 1-830-278

• Thread Size: M 10x1
• Housing Colour: green
• Pressure [bar]: 0.5
• Manufacturer: FAE

• Switch Pressure [bar]: 0.5
• Thread Size: M10x1
• Colour: green/blue
• Version: Neue Version
• Manufacturer: METZGER

• Supplementary Article/Info 2: without cable
• Socket colour: black
• Fabrication Number: ESS-VW-000
• Manufacturer: NTY

• Thread Size: M 10 x 1
• Control Range [bar]: 0,3-0,6
• Weight [kg]: 0.033
• Manufacturer: VEMO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Housing Colour: grey
• Number of pins: 2
• Spanner Size: 0
• Manufacturer: DELPHI

• Number of pins: 2
• Colour Coding: grey
• Supplementary Article/Info 2: with seal ring
• Manufacturer: AIC

General Information: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.

• Number of pins: 2
• Weight [kg]: 0.3
• Packaging length [cm]: 12
• Packaging width [cm]: 8
• Packaging height [cm]: 6

• Version: 2
• Connector Shape: D Shape
• Material: Plastic
• Number of pins: 2
• Plug Type: Female
• Sensor Type: NTC Sensor
• Spanner Size: not have
• Thread Size: not have
• Manufacturer: NISSENS

Technical Information: FIRST FIT - a time-saving installation! Find all additional parts such as O-rings, clip, washer in the box.

• Mounting Type: Plugged
• Voltage [V]: 12
• Supplementary Article/Supplementary Info: with seal
• Colour: black
• Sensor Type: NTC Sensor
• Number of pins: 2
• Supplementary Article/Info 2: with retaining ring
• Corresponds to the original part in colour: black, grey
• Fitting Depth [mm]: 20
• Assy./disassy. by qualified personnel required!:
• SVHC: 7439-92-1; Lead
• Name: HE 6PT009309331
• Manufacturer: HELLA

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Number of connectors: 2
• Colour Coding: grey
• Screw length below head [mm]: 20
• Weight [kg]: 0.015
• Supplementary Article/Supplementary Info: with seal, with retaining spring
• Manufacturer: FEBI

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

Manufacturer: DELLO AUTOMEGA

• Number of connectors: 2
• Colour Coding: grey
• Screw length below head [mm]: 20
• Weight [kg]: 0.03
• Supplementary Article/Supplementary Info: with retaining spring, with seal
• Manufacturer: SWAG

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• for OE number: 03D 907 601
• Length [mm]: 60
• Supplementary Article/Info 2: with seal ring
• Fabrication Number: ECP-AU-004
• Manufacturer: NTY

• Colour Coding: grey
• Corresponds to the original part in colour: black
• Number of pins: 2
• Supplementary Article/Supplementary Info: with seal
• Quality: IAM
• Article number of recommended accessories: 0899250, 0905513
• Power [W]: 0.06
• Manufacturer: METZGER

• Sensor Type: Active sensor
• for OE number: 30907601
• Manufacturer: KAMOKA

• Sensor Type: Hall Sensor
• Number of pins: 3
• Component Number: 120-04-005
• Manufacturer: ABAKUS DEPO/LORO

General Information: The following information is for general and informational purposes only and does not constitute warranty terms. Warranty terms and conditions are available from our dealers and in our general terms and conditions of sale. Abakus spare/repair parts are intended only for vehicle repairs in order to restore their original functionality. Abakus spare/repair parts are used or sold to users only for the purpose of repairing vehicles to restore their original look and functionality and are not original/genuine/OE/OEM/OES replacement parts. Our products are delivered without instruction of installation. Installation of our product may only be carried out by trained specialist technicians in specific car repairs. Products supplied by us are exclusively intended for proper and appropriate use. The warranty may become invalid in the event of: improper installation or repair, unsuitable application or use, installation or repair made outside specialist car workshops. Warranty claims are lost if the vehicle is modified and used for motor sports, tuning or similar events (except our tuning parts which are described in TecDoc and on our price list). Warranty application should include complete documentation among others: chassis no., first registration, vehicle mileage, information about LPG installation, fault memory log, pictures, our QC (quality check) code, installation invoice, contact details of the car repair workshop performing the replacement or repair. Warranty application are available in our Client Panel system. Complaints may require supplementing data such as error memory logs. Incomplete documentation may result in rejection of the claim. Any damage caused during transport is not considered quality damage and will be considered on an individual basis.

Manufacturer: MAGNETI MARELLI

• Number of pins: 2
• Connector Shape: D Shape
• Supplementary Article/Info 2: without cable
• for OE number: 030 905 377 C, YM21 12A699 BA
• Manufacturer: MEAT&DORIA

• for OE number: 03C 906 433 E
• Length [mm]: 69
• Supplementary Article/Info 2: with screw
• Fabrication Number: ECP-AU-011

• Fabrication Number: ECP-AU-035
• Manufacturer: NTY

• Colour: black
• Number of pins: 2
• Weight [kg]: 0.058
• Manufacturer: ERA

• Colour: grey
• Sensor Type: Active sensor
• for OE number: 036 906 433 A
• Manufacturer: KAMOKA

• Construction Year to: 02.2008
• Vehicle Identification Number (VIN) to: 1K8575000
• Height [mm]: 23.9
• Sensor Type: Hall Sensor
• Number of connectors: 3
• Manufacturer: VERNET

• Number of pins: 3
• Weight [kg]: 0.03
• Warranty: 3 years warranty
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY
• Name: CE 17SKV507

• Number of connectors: 3
• Housing Colour: grey
• Supplementary Article/Info 2: with cable
• Manufacturer: JP GROUP
• Lisainfo: Sensor, camshaft position
• Additional information: Sensor, camshaft position

• Quantity: 1
• Colour: black
• Weight [kg]: 0.48
• Number of connectors: 2
• General Information: knock sensor
• Manufacturer: VIKA

• Vehicle Identification Number (VIN) from: 1K_8_575001
• Height [mm]: 20
• Sensor Type: Hall Sensor
• Number of connectors: 3
• Manufacturer: VERNET

• Voltage [V]: 12
• Supplementary Article/Supplementary Info: without cable pull
• Number of pins: 3
• Weight [kg]: 0.03
• Operating Mode: Electric
• Warranty: 3 years warranty
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY

• Diameter [mm]: 26
• Number of pins: 2
• Supplementary Article/Info 2: with seal ring
• Spring Design: Retaining Spring
• Length [mm]: 20
• Housing Colour: blue
• Height [mm]: 57
• Weight [kg]: 0.02
• Colour: grey
• Number of connectors: 2
• Manufacturer: VEMO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Engine Code: BMY
• Vehicle Identification Number (VIN) to: 1K_8_575000
• Manufacturer Restriction: KACO
• Name: EP 1.953.464
• Manufacturer: EPS
• Additional information: 1-953-464
• Lisainfo: 1-953-464

• Number of pins: 2
• Housing Colour: grey
• Manufacturer: FAE

• Number of pins: 3
• Connector Shape: D Shape
• Number of mounting bores: 1
• Supplementary Article/Supplementary Info: with seal
• for OE number: 030907601E
• Manufacturer: DELLO AUTOMEGA

• Engine Code: BMY
• Vehicle Identification Number (VIN) from: 1K_8_575001
• Name: EP 1.953.598
• Manufacturer: EPS

• Quantity: 1
• Vehicle Identification Number (VIN) from: 1K-8-100 001, 1K-8-575 001
• Supplementary Article/Info 2: with screw
• Colour: black
• Length [mm]: 69
• Width [mm]: 31
• Weight [kg]: 0.02
• Required quantity: 1
• Number of connectors: 3
• General Information: impulse sender; crackshaft; black
• Manufacturer: VIKA

Vehicle Identification Number (VIN) to: 1K-7P027 000, 1K-7U020 900, 1K-7W149 000, 1K-8-100 000, 1K-8-575 000

• Number of pins: 2
• Colour: black
• Material: Plastic
• Manufacturer: AIC

General Information: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.

• Length [mm]: 60
• Width [mm]: 40
• Thickness [mm]: 22
• Number of connectors: 3
• Weight [kg]: 0.02
• Supplementary Article/Info 2: with seal ring
• Manufacturer: FEBI

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Number of pins: 3
• Supplementary Article/Info 2: without cable, with seal ring

• Voltage [V]: 12
• Number of pins: 2
• Tightening Torque [Nm]: 20
• Supplementary Article/Info 2: without cable
• Corresponds to the original part in colour: black
• Plug Type: Blade Terminal
• Connector Shape: oval
• Assy./disassy. by qualified personnel required!:
• Name: HE 6PG013114301
• Manufacturer: HELLA

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Engine Code: BMY
• Number of pins: 3
• Name: DE SS10773-12B1
• Manufacturer: DELPHI

Additional information: "Tootja: DELPHI
BORA (1J2), 10.98-09
(kvaliteediklass: PJ)" Lisainfo: "Tootja: DELPHI
BORA (1J2), 10.98-09
(kvaliteediklass: PJ)"

Manufacturer: BOSCH

• Number of pins: 3
• Manufacturer: DELPHI
• Name: DE SS11238

• Number of pins: 2
• Manufacturer: DELPHI
• Name: DE AS10169

• Length [mm]: 60
• Width [mm]: 40
• Thickness [mm]: 22
• Number of connectors: 3
• Weight [kg]: 0.02
• Supplementary Article/Info 2: with seal ring
• Name: SW 30 94 4382
• Manufacturer: SWAG

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Colour: grey
• Alternatively:
• Number of pins: 3
• Weight [kg]: 0.024
• Alternative Repair Kit: 550119
• Fitting Depth [mm]: 19.5
• Manufacturer: ERA

• Vehicle Identification Number (VIN) to: 1K8575000
• Number of pins: 3
• Manufacturer: DELPHI
• Name: DE SS10772-12B1

• Alternatively:
• Number of pins: 3
• Manufacturer: DELPHI

• Lambda Sensor: Regulating Probe, Thread pre-greased
• Thread Size: M18x1.5
• Cable Length [mm]: 880
• Number of circuits: 4
• Fitting Position: before catalytic converter
• Fabrication Number: ESL-AU-013
• Manufacturer: NTY

• Sensor Type: Hall Sensor
• Number of pins: 3
• Connector Shape: D Shape
• Supplementary Article/Info 2: with screw, without cable
• Manufacturer: TOPRAN HANS PRIES

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Number of pins: 3
• Connector Shape: D Shape
• Socket colour: light grey
• Manufacturer: FAE

• Vehicle Identification Number (VIN) to: 1K_8_575000
• Number of mounting bores: 1
• Voltage [V]: 12
• Fitting Depth [mm]: 23.9
• Sensor Type: Hall Sensor
• Number of pins: 3
• Corresponds to the original part in colour: Milk White
• Assy./disassy. by qualified personnel required!:
• Manufacturer: HELLA

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Length [mm]: 69
• Width [mm]: 31
• Number of connectors: 3
• Weight [kg]: 0.02
• Supplementary Article/Info 2: with screw
• Manufacturer: FEBI

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Vehicle Identification Number (VIN) to: 1K8575000
• Vehicle Identification Number (VIN) from: 1K8575001
• for OE number: 03C 906 433 E
• Width [mm]: 30
• Height [mm]: 28
• Length [mm]: 80
• Weight [kg]: 0.025
• Number of pins: 3
• Supplementary Article/Info 2: for crankshaft, with screw, without cable
• Required quantity: 1
• Sensor Type: Hall Sensor
• Number of connectors: 3
• Rated Voltage [V]: 12
• Fitting Depth [mm]: 20
• Connector Shape: D Shape
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Sensor Type: Hall Sensor
• Number of pins: 3
• Voltage [V]: 12
• Connector Shape: D Shape
• Supplementary Article/Info 2: without cable
• Weight [kg]: 0.03
• Manufacturer: VALEO
• Name: VA 253802

• Vehicle Identification Number (VIN) to: 1K8575000
• for OE number: 045906433A
• Required quantity: 1
• Sensor Type: Hall Sensor
• Supplementary Article/Info 2: for crankshaft, with screw, without cable
• Colour: grey
• Operating Mode: Electric
• Number of pins: 3
• Number of connectors: 3
• Rated Voltage [V]: 12
• Fitting Depth [mm]: 23.9
• Connector Shape: D Shape
• Number of mounting bores: 1
• Weight [kg]: 0.024
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Length [mm]: 69
• Width [mm]: 31
• Number of connectors: 3
• Weight [kg]: 0.02
• Supplementary Article/Info 2: with screw
• Name: SW 30 93 7317
• Manufacturer: SWAG

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Vehicle Identification Number (VIN) from: 1K_8_575001
• Fitting Depth [mm]: 20
• Sensor Type: Hall Sensor
• Number of pins: 3
• Supplementary Article/Info 2: with screw
• Assy./disassy. by qualified personnel required!:
• SVHC: 7439-92-1; Lead, 872-50-4; 1-Methyl-2-pyrrolidone
• Name: HE 6PU009167131
• Manufacturer: HELLA

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Required quantity: 1
• Sensor Type: Hall Sensor
• Number of pins: 3
• Assy./disassy. by qualified personnel required!:
• Name: HE 6PU013122671
• Manufacturer: HELLA

Brief Information: *** HELLA Electronics OE competence for over 60 years.

Manufacturer: BOSCH

• Number of pins: 3
• Sensor Type: Hall Sensor
• Connector Shape: D Shape
• Manufacturer: FAE

• Number of pins: 3
• Manufacturer: AIC

General Information: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.

• Number of pins: 3
• Connector Shape: D Shape
• Sensor Type: Hall Sensor
• Supplementary Article/Info 2: without cable, with screw
• for OE number: 045 906 433 A
• Manufacturer: MEAT&DORIA