• Engine Code: BGW
• Inner Diameter [mm]: 43.95
• Manufacturer: JP GROUP
• Lisainfo: Seal, turbo air hose
• Additional information: Seal, turbo air hose

• Inner Diameter [mm]: 57.85
• Manufacturer: JP GROUP
• Lisainfo: Seal, turbo air hose
• Additional information: Seal, turbo air hose

• Inner Diameter [mm]: 58.5
• Name: Rongastihend,ohulaadevoolik
• Manufacturer: MAX

• Braking/Drive Dynamics: for vehicles without ABS
• Name: Rongastihend,ohulaadevoolik
• Manufacturer: MAX

• Weight [kg]: 0.003
• Packaging length [cm]: 5.3
• Packaging width [cm]: 5.3
• Packaging height [cm]: 0.5
• Manufacturer: FEBEST

• Engine Code: BGW
• Inner Diameter [mm]: 57.85
• Manufacturer: DR MOTOR PRZEWODY PRZELEWOWE

• Quantity per packing unit: 5
• for OE number: 3C0145117
• Quantity Unit: Packing Unit
• Weight [g]: 4
• Material: FKM (fluorocarbon rubber)
• Name: Rongastihend,ohulaadevoolik
• Manufacturer: IBR

• Weight [kg]: 0.005
• Inner Diameter [mm]: 58
• Packaging length [cm]: 6.9
• Packaging width [cm]: 6.9
• Packaging height [cm]: 0.5
• Manufacturer: FEBEST

• for OE number: 3C0145117J
• Weight [g]: 11
• Name: IM 20280
• Manufacturer: ORIGINAL IMPERIUM

• Engine Code: BGW
• Inner Diameter [mm]: 57.85
• Shape: Ring Form
• Material: FPM (fluoride rubber)
• Always compare old and new part (in particular OE No.):
• Alternative Repair Kit: 2400113, 2400118, 2400119, 2400129, 2400277
• Manufacturer: METZGER

• for OE number: 3C0145117F
• Weight [g]: 12
• Name: IM 20282
• Manufacturer: ORIGINAL IMPERIUM

• Quantity per packing unit: 10
• Diameter [mm]: 44
• Weight [kg]: 0.025
• Manufacturer: VAICO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Engine Code: BGW
• Quantity per packing unit: 10
• Diameter [mm]: 56
• Weight [kg]: 0.006
• Manufacturer: VAICO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• for OE number: 3B0 145 838 A
• Material: Rubber with fabric lining
• Connector Ø pressure side [mm]: 57
• Connector Ø suction side [mm]: 63
• Fabrication Number: GPP-VW-018
• Manufacturer: NTY

• Material: Rubber with fabric lining
• Connector Ø pressure side [mm]: 56
• Connector Ø suction side [mm]: 62
• Fabrication Number: GPP-VW-017
• Manufacturer: NTY

• Material: Rubber with fabric lining
• Connector Ø pressure side [mm]: 60
• Connector Ø suction side [mm]: 65
• Fabrication Number: GPP-VW-016
• Manufacturer: NTY

• Quantity per packing unit: 5
• Shape: O-Ring
• Inner Diameter [mm]: 58
• Thickness [mm]: 4.5
• Material: FPM (fluoride rubber)
• Alternatively:

• Material: Rubber with fabric lining
• Component Number: 053-028-022
• Manufacturer: ABAKUS DEPO/LORO

General Information: The following information is for general and informational purposes only and does not constitute warranty terms. Warranty terms and conditions are available from our dealers and in our general terms and conditions of sale. Abakus spare/repair parts are intended only for vehicle repairs in order to restore their original functionality. Abakus spare/repair parts are used or sold to users only for the purpose of repairing vehicles to restore their original look and functionality and are not original/genuine/OE/OEM/OES replacement parts. Our products are delivered without instruction of installation. Installation of our product may only be carried out by trained specialist technicians in specific car repairs. Products supplied by us are exclusively intended for proper and appropriate use. The warranty may become invalid in the event of: improper installation or repair, unsuitable application or use, installation or repair made outside specialist car workshops. Warranty claims are lost if the vehicle is modified and used for motor sports, tuning or similar events (except our tuning parts which are described in TecDoc and on our price list). Warranty application should include complete documentation among others: chassis no., first registration, vehicle mileage, information about LPG installation, fault memory log, pictures, our QC (quality check) code, installation invoice, contact details of the car repair workshop performing the replacement or repair. Warranty application are available in our Client Panel system. Complaints may require supplementing data such as error memory logs. Incomplete documentation may result in rejection of the claim. Any damage caused during transport is not considered quality damage and will be considered on an individual basis.

• Quantity per packing unit: 5
• Inner Diameter [mm]: 43.95
• Quantity: 5
• Name: Rongastihend,ohulaadevoolik
• Manufacturer: DRM

• for OE number: 3B0 145838 A
• Fitting Position: Upper
• Length [mm]: 185
• Outer Diameter 1 [mm]: 56
• Outer Diameter 2 [mm]: 64
• Name: Laadimisohu voolik
• Manufacturer: MAX

• for OE number: 8D0145834L
• Weight [g]: 181
• Connector Manufacturer: HENN
• Length [mm]: 146
• Inner Diameter 1 [mm]: 50
• Inner Diameter 2 [mm]: 47
• Manufacturer: IMPERGOM
• Name: IM 221863

• Engine Code: BGW
• Fitting Position: Upper, Right, Rear
• Manufacturer: JP GROUP
• Lisainfo: Charger Intake Hose
• Additional information: Charger Intake Hose

• for OE number: 3B0 145834 P
• Fitting Position: Upper
• Length [mm]: 188
• Outer Diameter [mm]: 65
• Name: KOMPRESSORIOHUVOOLIK
• Manufacturer: MAX

• Fitting Position: Upper, engine sided
• Supplementary Article/Supplementary Info: with seal, with quick coupling
• Hose Type: Moulded Hose
• Manufacturer: TOPRAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• for OE number: 3B0145838A
• Name: Laadimisohu voolik
• Manufacturer: NRF

• for OE number: 3B0 145834 P
• Fitting Position: Upper
• Length [mm]: 188
• Outer Diameter [mm]: 65
• Name: KOMPRESSORIOHUVOOLIK
• Manufacturer: BUG

• Inner Diameter [mm]: 49
• Outer Diameter [mm]: 58
• Outer Diameter 1 [mm]: 65
• Manufacturer: FAST

• Fitting Position: Right Rear
• Cooling Hose: Piping to engine block, Cold Side
• Weight [kg]: 0.22
• Guarantee: 3 years guarantee
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY
• Name: CE 24SKV029

• for OE number: 3B0 145 834 N
• Material: Rubber with fabric lining
• Connector Ø pressure side [mm]: 58
• Connector Ø suction side [mm]: 62
• Fabrication Number: GPP-VW-026
• Manufacturer: NTY

• Engine Code: BGW
• Fitting Position: Lower
• Lisainfo: Charger Intake Hose
• Additional information: Charger Intake Hose

• Weight [kg]: 0.2
• Guarantee: 3 years guarantee
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY
• Name: CE 43SKV102

• for OE number: 3B0145838A
• Quantity Unit: Piece
• Weight [g]: 200
• Material, 1st layer: NBR (nitrile butadiene rubber)
• Material, 2nd layer: Aramid
• Material, 3rd layer: CR (chloroprene rubber)
• Name: Laadimisohu voolik
• Manufacturer: IBR

• General Information: pressure hose
• Manufacturer: VIKA

• Fitting Position: Right Front
• Weight [kg]: 0.36
• Guarantee: 3 years guarantee
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY
• Name: CE 24SKV002

Manufacturer: FAST

• Weight [kg]: 0.32
• Guarantee: 3 years guarantee
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY
• Name: CE 24SKV025

• Fitting Position: Left Rear
• Inner Diameter [mm]: 49
• Cooling Hose: Piping to engine block, Cold Side
• Outer Diameter 1 [mm]: 58
• Outer Diameter 2 [mm]: 65
• Weight [kg]: 0.28
• Guarantee: 3 years guarantee
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY
• Name: CE 24SKV012

• for OE number: 3B0 145838 A
• Fitting Position: Upper
• Length [mm]: 185
• Outer Diameter 1 [mm]: 56
• Outer Diameter 2 [mm]: 64
• Material: AEM (Ethylene Acrylate Rubber)
• Supplementary Article/Info 2: with clamp
• Name: KOMPRESSORIOHUVOOLIK
• Manufacturer: BUG

• Engine Code: BGW
• Lisainfo: Charger Intake Hose
• Additional information: Charger Intake Hose

• for OE number: 3B0 145828 G
• Fitting Position: Charge Air Cooler, Lower
• Length [mm]: 374
• Outer Diameter 1 [mm]: 65
• Outer Diameter 2 [mm]: 50
• Name: KOMPRESSORIOHUVOOLIK
• Manufacturer: MAX

• for OE number: 8D0145834J
• Weight [g]: 320
• Connector Manufacturer: HENN
• Length [mm]: 170
• Inner Diameter 1 [mm]: 51
• Inner Diameter 2 [mm]: 51
• Manufacturer: IMPERGOM

• Fitting Position: Charge Air Cooler, Inlet
• Name: Laadimisohu voolik
• Manufacturer: NRF

• Engine Code: BGW
• Fitting Position: Upper
• Lisainfo: Charger Intake Hose
• Additional information: Charger Intake Hose

• for OE number: 3B0 145828 G
• Fitting Position: Charge Air Cooler, Lower
• Length [mm]: 374
• Outer Diameter 1 [mm]: 65
• Outer Diameter 2 [mm]: 50
• Name: KOMPRESSORIOHUVOOLIK
• Manufacturer: BUG

• Connector Ø pressure side [mm]: 56
• Connector Ø suction side [mm]: 62
• Compression ring material: Stainless Steel
• Weight [kg]: 0.117
• Material: Rubber with fabric lining
• Manufacturer: VAICO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Fitting Position: Charge Air Cooler, Inlet
• Manufacturer: FAST

• Fitting Position: Lower, Right
• Manufacturer: FAST

• Fitting Position: Right Front
• Cooling Hose: Charge air cooler to piping, Cold Side
• Weight [kg]: 0.5
• Guarantee: 3 years guarantee
• Always compare old and new part (in particular OE No.):
• Name: CE 24SKV069
• Manufacturer: ESEN SKV

• Construction Year from: 11.2003
• Construction Year to: 12.2005
• Turbocharger Line: Hot Side, Piping to charge air cooler
• Material: AEM (Ethylene Acrylate Rubber)
• Colour: black
• Hose Length [mm]: 150
• Inner Diameter 1 [mm]: 48
• Inner Diameter 2 [mm]: 48
• Observe broschure:
• Manufacturer: GATES

• Fitting Position: Charge Air Cooler, Upper
• Supplementary Article/Supplementary Info: with gaskets/seals
• Hose Type: Moulded Hose
• Supplementary Article/Info 2: with quick couplers
• Manufacturer: TOPRAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Construction Year from: 11.2003
• Construction Year to: 12.2005
• Turbocharger Line: Cold Side, Piping to engine block
• Material: PE (Polyethylene)
• Colour: black
• Hose Length [mm]: 150
• Inner Diameter 1 [mm]: 47
• Inner Diameter 2 [mm]: 50
• Observe broschure:
• Manufacturer: GATES

• Fitting Position: Outlet
• for OE number: 3B0145828G
• Name: KOMPRESSORIOHUVOOLIK
• Manufacturer: SAS

• for OE number: 8D0145834K
• Weight [g]: 610
• Connector Manufacturer: HENN
• Length [mm]: 422
• Inner Diameter 1 [mm]: 52
• Inner Diameter 2 [mm]: 52
• Manufacturer: IMPERGOM
• Name: IM 221847

• Engine Code: BGW
• Thickness [mm]: 5
• Inner Diameter [mm]: 46
• Outer Diameter [mm]: 65
• Weight [kg]: 0.33
• Guarantee: 3 years guarantee
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY
• Name: CE 24SKV509

• Fitting Position: Lower, Front
• Connector type: OE PUSH CONNECTOR
• Length [mm]: 150
• Colour: black
• Material: AEM (Ethylene Acrylate Rubber)
• Supplementary Article/Info 2: without hose clip
• Inner Diameter 1 [mm]: 48
• Inner Diameter 2 [mm]: 48
• Manufacturer: BORG & BECK

• Fitting Position: Charge Air Cooler, Inlet
• for OE number: 3B0145834AC
• Name: KOMPRESSORIOHUVOOLIK
• Manufacturer: SAS

• for OE number: 3B0145834N
• Quantity Unit: Piece
• Weight [g]: 605
• Material, 1st layer: NBR (nitrile butadiene rubber)
• Material, 2nd layer: Aramid
• Material, 3rd layer: CR (chloroprene rubber)
• Name: Laadimisohu voolik
• Manufacturer: IBR

• Fitting Position: Charge Air Cooler
• for OE number: 8D0145834K
• Name: Laadimisohu voolik
• Manufacturer: NRF

• General Information: pressure hose
• Manufacturer: VIKA

• Connector Ø pressure side [mm]: 46
• Connector Ø suction side [mm]: 59
• Compression ring material: Stainless Steel
• for OE number: 3B0 145 828 G
• Material: Rubber with fabric lining
• Weight [kg]: 0.39
• Manufacturer: VAICO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Fitting Position: Charge Air Cooler, Outlet
• for OE number: 3B0145834N
• Name: KOMPRESSORIOHUVOOLIK
• Manufacturer: SAS

• Turbocharger Line: Piping to charge air cooler
• Material: ACM (Polyacrylate)
• Fitting Position: Charge Air Cooler, Upper
• Weight [kg]: 0.56
• Supplementary Article/Info 2: with quick couplers
• Name: KOMPRESSORIOHUVOOLIK
• Manufacturer: FEB
• Additional information: FE101435
• Lisainfo: FE101435

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Engine Code: BGW
• Material: AEM (Ethylene Acrylate Rubber)
• Name: KOMPRESSORIOHUVOOLIK
• Manufacturer: MEY

• Fitting Position: Upper
• Manufacturer: AIC

General Information: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.

• Construction Year from: 11.2003
• Construction Year to: 12.2005
• Turbocharger Line: Cold Side, Charge air cooler to piping
• Material: AEM (Ethylene Acrylate Rubber)
• Colour: black
• Hose Length [mm]: 500
• Inner Diameter 1 [mm]: 48
• Inner Diameter 2 [mm]: 48
• Observe broschure:
• Manufacturer: GATES

• Turbocharger Line: Hot Side, Piping to charge air cooler
• Connector Ø pressure side [mm]: 60
• Connector Ø suction side [mm]: 65
• Weight [kg]: 0.115
• Material: Rubber with fabric lining
• Compression ring material: Stainless Steel
• Manufacturer: VAICO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Connector Ø pressure side [mm]: 58
• Connector Ø suction side [mm]: 62
• Compression ring material: Stainless Steel
• Material: Rubber with fabric lining
• for OE number: 3B0 145 834 N
• Weight [kg]: 0.614
• Manufacturer: VAICO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Quantity per packing unit: 100
• Shape: O-Ring
• Inner Diameter [mm]: 58
• Thickness [mm]: 4.5
• Material: FPM (fluoride rubber)