• Production date from: 01/99
• Production date to: 12/01
• for OE number: 059919501
• Manufacturer: SASIC

• General Information: Exterior temperature sensor
• Manufacturer: VIKA

• General Information: Fuel temperature sensor
• Manufacturer: VIKA
• Additional information: VIK99061780801
• Lisainfo: VIK99061780801

• Fitted Diameter [mm]: 20
• Number of pins: 4
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: MAX

• Number of pins: 4
• Socket colour: dark green
• Fitted Diameter [mm]: 20
• Diameter [mm]: 25.5
• for OE number: 059919501
• Manufacturer: MEAT&DORIA

• Vehicle Identification Number (VIN) to: 1J X 250000
• Number of pins: 4
• Socket colour: light blue
• Connector Shape: angular
• for OE number: 078919501B
• Manufacturer: MEAT&DORIA

• Number of pins: 4
• Socket colour: black
• Connector Shape: D Shape
• Fitted Diameter [mm]: 20
• Diameter [mm]: 25.5
• for OE number: 078919501C
• Manufacturer: MEAT&DORIA

• Engine Code: AJM
• Colour: grey
• for article number: 1.660.015K, 1.830.278K, 1.879.946
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: EPS
• Additional information: 1-830-278
• Lisainfo: 1-830-278

• Engine Code: AJM
• Housing Colour: green
• Corresponds to the original part in colour: black
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: EPS

• Engine Code: AJM
• Colour: grey
• for article number: 26.0015K, 7.3278K, 7.7946
• Manufacturer: FACET

• Engine Code: AJM
• Housing Colour: green
• Corresponds to the original part in colour: black
• Manufacturer: FACET

• Vehicle Identification Number (VIN) from: 1J X 250001
• Number of pins: 4
• Connector Shape: D Shape
• Socket colour: green
• Fitted Diameter [mm]: 20
• Diameter [mm]: 25.5
• for OE number: 059919501A
• Manufacturer: MEAT & DORIA

• Number of pins: 4
• Housing Colour: green
• Connector Shape: round
• Fitted Diameter [mm]: 20
• Manufacturer: FAE ELEKTRYKA

• General Information: Intake air temperature sensor
• Manufacturer: VIKA

• Engine Code: AJM
• Colour: blue
• Corresponds to the original part in colour: blue
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: EPS

• Housing Type: without housing
• Supplementary Article/Info 2: with clip, with seal ring
• Connector Shape: D Shape
• Sensor Type: NTC Sensor
• Manufacturer: TOPRAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Engine Code: AJM
• Colour: blue
• Corresponds to the original part in colour: blue
• Manufacturer: FACET

• Sensor Type: NTC Sensor
• Voltage [V]: 12
• Length [mm]: 20
• Colour Coding: grey
• Manufacturer: MAGNETI MARELLI
• Name: MM SPA111

• Number of connectors: 4
• Connector Shape: round
• Supplementary Article/Supplementary Info: with gasket/seal
• for OE number: 059 919 501 A
• Colour Coding: green
• Spring Design: Retaining Spring
• Number of pins: 4
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Number of pins: 2
• Connector Shape: D Shape
• Socket colour: black
• Sensor Type: NTC Sensor
• Mounting Type: Clipped
• Fitting Position: Fuel Line
• for OE number: 038906081B
• Name: Andur, ktusetemperatuur
• Manufacturer: MD

• Pressure from [kPA]: 20
• Pressure to [kPA]: 25
• Assy./disassy. by qualified personnel required!:
• Name: AB 120-08-004
• Manufacturer: ABAKUS

General Information: The following information is for general and informational purposes only and does not constitute warranty terms. Warranty terms and conditions are available from our dealers and in our general terms and conditions of sale. Abakus spare/repair parts are intended only for vehicle repairs in order to restore their original functionality. Abakus spare/repair parts are used or sold to users only for the purpose of repairing vehicles to restore their original look and functionality and are not original/genuine/OE/OEM/OES replacement parts. These items do not originate from the vehicle manufacturer and may be the subject of a design not owned by Abakus and the manufacturer of this spare part. They may only be used for repairs to restore the intended vehicle to its original appearance. Our products are delivered without instruction of installation. Installation of our product may only be carried out by trained specialist technicians in specific car repairs. Products supplied by us are exclusively intended for proper and appropriate use. The warranty may become invalid in the event of: improper installation or repair, unsuitable application or use, installation or repair made outside specialist car workshops. Warranty claims are lost if the vehicle is modified and used for motor sports, tuning or similar events (except our tuning parts which are described in TecDoc and on our price list). Warranty application should include complete documentation among others: chassis no., first registration, vehicle mileage, information about LPG installation, fault memory log, pictures, our QC (quality check) code, installation invoice, contact details of the car repair workshop performing the replacement or repair. Warranty application are available in our Client Panel system. Complaints may require supplementing data such as error memory logs. Incomplete documentation may result in rejection of the claim. Any damage caused during transport is not considered quality damage and will be considered on an individual basis. The product is intended for use within the performance limits specified by the manufacturer and should only be used by qualified personnel who have been trained to operate this product. Before each use, the product should be checked for damage or fixing of its parts and not used if any defects or loose parts are found. Failure to follow the manufacturer's guidelines could result in potential product damage or even injury. Wear appropriate protective clothing if necessary when working with the product.

• Plug housing design: Plug sleeve housing
• Manufacturer Restriction: VAG
• Cable Length [mm]: 500
• Number of pins: 2
• Supplementary Article/Info 2: with pipe
• Cable Cross Section [mm²]: 0.75
• Socket Width [mm]: 1.5
• Temperature range from [°C]: -25
• Temperature range to [°C]: +140
• Cable insulation material: Silicone
• Current carrying capacity [A]: 9
• Operating voltage [V]: 24
• for OE number: 1J6 943 021 B, 1JE 943 021, 1K8 943 021 C
• for article number: 70660022
• SVHC: No SVHC present!
• Name: Kaabli remondikomplekt,
• Manufacturer: HBE

Supplementary Article/Supplementary Info: with socket housing, with gaskets/seals, with heat shrink tubing

• Construction Year from: 01.2000
• Number of pins: 3
• Guarantee: 3 years guarantee
• Weight [kg]: 0.06
• Always compare old and new part (in particular OE No.):
• Name: CE 17SKV486
• Manufacturer: ESEN SKV

• Vehicle Identification Number (VIN) from: 1J-W-000 001
• Cable Length [mm]: 280
• Number of connectors: 3
• Housing Colour: black
• Lisainfo: Sensor, camshaft position
• Additional information: Sensor, camshaft position

• Length [mm]: 445
• Number of pins: 3
• Sensor Type: Hall Sensor
• Assy./disassy. by qualified personnel required!:
• Manufacturer: ABAKUS

General Information: The following information is for general and informational purposes only and does not constitute warranty terms. Warranty terms and conditions are available from our dealers and in our general terms and conditions of sale. Abakus spare/repair parts are intended only for vehicle repairs in order to restore their original functionality. Abakus spare/repair parts are used or sold to users only for the purpose of repairing vehicles to restore their original look and functionality and are not original/genuine/OE/OEM/OES replacement parts. These items do not originate from the vehicle manufacturer and may be the subject of a design not owned by Abakus and the manufacturer of this spare part. They may only be used for repairs to restore the intended vehicle to its original appearance. Our products are delivered without instruction of installation. Installation of our product may only be carried out by trained specialist technicians in specific car repairs. Products supplied by us are exclusively intended for proper and appropriate use. The warranty may become invalid in the event of: improper installation or repair, unsuitable application or use, installation or repair made outside specialist car workshops. Warranty claims are lost if the vehicle is modified and used for motor sports, tuning or similar events (except our tuning parts which are described in TecDoc and on our price list). Warranty application should include complete documentation among others: chassis no., first registration, vehicle mileage, information about LPG installation, fault memory log, pictures, our QC (quality check) code, installation invoice, contact details of the car repair workshop performing the replacement or repair. Warranty application are available in our Client Panel system. Complaints may require supplementing data such as error memory logs. Incomplete documentation may result in rejection of the claim. Any damage caused during transport is not considered quality damage and will be considered on an individual basis. The product is intended for use within the performance limits specified by the manufacturer and should only be used by qualified personnel who have been trained to operate this product. Before each use, the product should be checked for damage or fixing of its parts and not used if any defects or loose parts are found. Failure to follow the manufacturer's guidelines could result in potential product damage or even injury. Wear appropriate protective clothing if necessary when working with the product.

• for OE number: 058 919 501 A
• Number of pins: 4
• Fitted Diameter [mm]: 20
• Housing Colour: black
• Manufacturer: FAE

• for OE number: 03G 906 433
• Sensor Type: Active sensor
• Manufacturer: KAMOKA

• for OE number: 1100748
• Sensor Type: Active sensor
• Manufacturer: KAMOKA

• Number of pins: 4
• Name: ANDUR,KOMPRESSORIROHK
• Manufacturer: MAX

• Number of pins: 2
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Engine Code: AJM
• Number of pins: 4
• Manufacturer: JPN

• Number of connectors: 4
• Diameter [mm]: 25
• Length [mm]: 50
• Supplementary Article/Supplementary Info: with gasket/seal
• for OE number: 059 919 501
• Spring Design: Retaining Spring
• Number of pins: 4
• Connector Shape: angular
• Manufacturer: VEMO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Voltage [V]: 12
• Length [mm]: 340
• Number of pins: 3
• Guarantee: 3 years guarantee
• Weight [kg]: 0.08
• Operating Mode: Electric
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY
• Name: CE 17SKV365

• Number of pins: 4
• Plug Type: Female
• Number of circuits: 4
• Cable insulation material: Silicone
• Material: CuSn (copper-tin)
• Cable Length [mm]: 250
• Cable cross-section from [mm²]: 0.5
• Cable cross-section to [mm²]: 0.5
• Manufacturer: 3RG

• Number of pins: 4
• Colour Coding: white
• Manufacturer: VEMO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Diameter [mm]: 26
• Number of pins: 2
• Supplementary Article/Info 2: with seal ring
• Spring Design: Retaining Spring
• Length [mm]: 20
• Housing Colour: blue
• Height [mm]: 57
• Colour: grey
• Number of connectors: 2
• Manufacturer: VEMO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Supplementary Article/Supplementary Info: with gasket/seal
• Number of pins: 4
• Mounting Type: Pressed
• Assy./disassy. by qualified personnel required!:
• Manufacturer: HELLA

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Construction Year from: 10.2000
• Number of pins: 3
• Connector Shape: D Shape
• Sensor Type: Hall Sensor
• for OE number: 045957147B
• Name: Andur,Nukkvollipositsioon
• Manufacturer: MD

• Voltage [V]: 12
• Supplementary Article/Supplementary Info: without cable pull
• Number of pins: 4
• Guarantee: 3 years guarantee
• Weight [kg]: 0.04
• Operating Mode: Electric
• Always compare old and new part (in particular OE No.):
• Name: CE 17SKV127
• Manufacturer: ESEN SKV

• Construction Year from: 01.2000
• Engine Code: AJM,AUY
• Sensor Type: Hall Sensor
• Number of pins: 3
• Voltage [V]: 12
• Connector Shape: D Shape
• Supplementary Article/Info 2: with cable
• Name: ANDUR,NUKKVOLLIPOSITSIOON
• Manufacturer: VAL
• Lisainfo: VAL253807
• Additional information: VAL253807

• Supplementary Article/Info 2: with cable
• Length [mm]: 445
• Sensor Type: Hall Sensor
• Number of connectors: 3
• Manufacturer: VERNET

• Required quantity: 1
• Voltage [V]: 12
• Number of pins: 3
• Sensor Type: Hall Sensor
• Supplementary Article/Info 2: with cable
• Housing Colour: black
• Name: CZUJNIK POO½ENIA WAKA ROZRZ. VW POLO 01-
• Manufacturer: BRM

• Required quantity: 1
• Name: CZUJNIK CI—N. POWIETRZA
• Manufacturer: BRM

• Construction Year from: 10.2000
• Manufacturer: MAGNETI MARELLI

• Voltage [V]: 12
• Fabrication Number: EPP-AU-031
• Manufacturer: NTY

• Sensor Type: Hall Sensor
• Cable Length [mm]: 306
• Supplementary Article/Supplementary Info: with cable protection pipe
• Number of pins: 3
• Name: ANDUR,NUKKVOLLIPOSITSIOON
• Manufacturer: MEY

• Length [mm]: 245
• Number of pins: 3
• Name: ANDUR,NUKKVOLLIPOSITSIOON
• Manufacturer: DLP
• Quality class: PJ

Additional information: "Tootja: DELPHI
(kvaliteediklass: PJ)" Lisainfo: "Tootja: DELPHI
(kvaliteediklass: PJ)"

• Engine Code: AJM
• Colour: black
• Temperature range [°C]: 120
• Fitting Depth [mm]: 20
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: EPS

• Fabrication Number: EPP-AU-004
• Manufacturer: NTY

• Number of pins: 5
• Housing material: Plastic
• Housing Type: with housing
• Assy./disassy. by qualified personnel required!:
• Name: AB 120-08-068
• Manufacturer: ABAKUS

General Information: The following information is for general and informational purposes only and does not constitute warranty terms. Warranty terms and conditions are available from our dealers and in our general terms and conditions of sale. Abakus spare/repair parts are intended only for vehicle repairs in order to restore their original functionality. Abakus spare/repair parts are used or sold to users only for the purpose of repairing vehicles to restore their original look and functionality and are not original/genuine/OE/OEM/OES replacement parts. These items do not originate from the vehicle manufacturer and may be the subject of a design not owned by Abakus and the manufacturer of this spare part. They may only be used for repairs to restore the intended vehicle to its original appearance. Our products are delivered without instruction of installation. Installation of our product may only be carried out by trained specialist technicians in specific car repairs. Products supplied by us are exclusively intended for proper and appropriate use. The warranty may become invalid in the event of: improper installation or repair, unsuitable application or use, installation or repair made outside specialist car workshops. Warranty claims are lost if the vehicle is modified and used for motor sports, tuning or similar events (except our tuning parts which are described in TecDoc and on our price list). Warranty application should include complete documentation among others: chassis no., first registration, vehicle mileage, information about LPG installation, fault memory log, pictures, our QC (quality check) code, installation invoice, contact details of the car repair workshop performing the replacement or repair. Warranty application are available in our Client Panel system. Complaints may require supplementing data such as error memory logs. Incomplete documentation may result in rejection of the claim. Any damage caused during transport is not considered quality damage and will be considered on an individual basis. The product is intended for use within the performance limits specified by the manufacturer and should only be used by qualified personnel who have been trained to operate this product. Before each use, the product should be checked for damage or fixing of its parts and not used if any defects or loose parts are found. Failure to follow the manufacturer's guidelines could result in potential product damage or even injury. Wear appropriate protective clothing if necessary when working with the product.

• Engine Code: AJM
• Colour: black
• Fitting Depth [mm]: 20
• Manufacturer: FACET

• Length [mm]: 358
• Number of connectors: 3
• Cable Length [mm]: 265
• Weight [kg]: 0.04
• Manufacturer: FEBI BILSTEIN
• Additional information: F37607
• Lisainfo: F37607

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Connector Shape: D Shape
• Number of pins: 3
• Supplementary Article/Info 2: with cable
• Supplementary Article/Supplementary Info: with cable protection pipe
• Manufacturer: TOPRAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Number of connectors: 3
• Number of mounting bores: 1
• Rated Voltage [V]: 12
• Cable Length 1 [mm]: 377
• Operating temperature from [°C]: -40
• Operating temperature to [°C]: 125
• Sensor Type: Hall Sensor
• Connector Shape: D Shape
• Colour: black
• Name: SN CMP154.02
• Manufacturer: SNR

• Alternatively:
• Number of pins: 3
• Alternative Repair Kit: 550254
• Total Length [mm]: 450
• Manufacturer: ERA

• Alternatively:
• Number of pins: 4
• Pressure from [kPA]: 11
• Pressure to [kPA]: 254
• Weight [kg]: 0.026
• Alternative Repair Kit: 550132
• Manufacturer: ERA

• Number of pins: 5
• for OE number: 028906461
• Assy./disassy. by qualified personnel required!:
• Name: AB 120-08-070
• Manufacturer: ABAKUS

General Information: The following information is for general and informational purposes only and does not constitute warranty terms. Warranty terms and conditions are available from our dealers and in our general terms and conditions of sale. Abakus spare/repair parts are intended only for vehicle repairs in order to restore their original functionality. Abakus spare/repair parts are used or sold to users only for the purpose of repairing vehicles to restore their original look and functionality and are not original/genuine/OE/OEM/OES replacement parts. These items do not originate from the vehicle manufacturer and may be the subject of a design not owned by Abakus and the manufacturer of this spare part. They may only be used for repairs to restore the intended vehicle to its original appearance. Our products are delivered without instruction of installation. Installation of our product may only be carried out by trained specialist technicians in specific car repairs. Products supplied by us are exclusively intended for proper and appropriate use. The warranty may become invalid in the event of: improper installation or repair, unsuitable application or use, installation or repair made outside specialist car workshops. Warranty claims are lost if the vehicle is modified and used for motor sports, tuning or similar events (except our tuning parts which are described in TecDoc and on our price list). Warranty application should include complete documentation among others: chassis no., first registration, vehicle mileage, information about LPG installation, fault memory log, pictures, our QC (quality check) code, installation invoice, contact details of the car repair workshop performing the replacement or repair. Warranty application are available in our Client Panel system. Complaints may require supplementing data such as error memory logs. Incomplete documentation may result in rejection of the claim. Any damage caused during transport is not considered quality damage and will be considered on an individual basis. The product is intended for use within the performance limits specified by the manufacturer and should only be used by qualified personnel who have been trained to operate this product. Before each use, the product should be checked for damage or fixing of its parts and not used if any defects or loose parts are found. Failure to follow the manufacturer's guidelines could result in potential product damage or even injury. Wear appropriate protective clothing if necessary when working with the product.

• Length [mm]: 330
• Sensor Type: Hall Sensor
• Number of pins: 3
• Manufacturer: METZGER

• Engine Code: AJM
• Length [mm]: 340
• Name: ANDUR,NUKKVOLLIPOSITSIOON
• Manufacturer: EPS

• Length [mm]: 358
• Number of connectors: 3
• Cable Length [mm]: 265
• Weight [kg]: 0.04
• Name: SW 30 93 7607
• Manufacturer: SWAG

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Length [mm]: 260
• Sensor Type: Hall Sensor
• Number of pins: 3
• Assy./disassy. by qualified personnel required!:
• Name: ANDUR,NUKKVOLLIPOSITSIOON
• Manufacturer: HEL

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Connector Shape: D Shape
• Sensor Type: NTC Sensor
• Number of pins: 4
• Housing material: GRP (Glass fibre Reinforced Plastic)
• Supplementary Article/Info 2: with seal ring
• Manufacturer: TOPRAN

Vehicle Identification Number (VIN) to: 1J-3B139990, 1J-3P278330, 1J-3D390630, 1J-3U346620, 1J-3W385000 General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Length [mm]: 380
• Number of pins: 3
• Cable Length [mm]: 445, 330
• Required quantity: 1
• Sensor Type: Active sensor, Hall Sensor
• Number of connectors: 3
• Rated Voltage [V]: 12
• Supplementary Article/Info 2: with cable
• Housing Colour: black
• Connector Shape: D Shape
• Number of mounting bores: 1
• Socket colour: black
• for OE number: 045 957 147 A
• Manufacturer: VIEROL

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Sensor Type: Piezoelectric Sensor
• Number of pins: 4
• Name: Andur,ohuvotu rohk
• Manufacturer: MEY
• Lisainfo: 1148120006
• Additional information: 1148120006

Supplementary Article/Info 2: with integrated air temperature sensor, with seal ring

• Operating Mode: Electric
• Manufacturer: MAGNETI MARELLI

• Number of pins: 4
• Pressure from [kPA]: 26
• Manufacturer: DELPHI

• Fitting Position: before catalytic converter
• Observe technical data:
• Manufacturer Restriction: VAG
• Number of pins: 6
• Cable Length [mm]: 250
• Cable Cross Section [mm²]: 1
• Socket Width [mm]: 2.8
• Contact surface: Tin-plated
• Supplementary Article/Supplementary Info: with socket housing, with gaskets/seals
• Supplementary Article/Info 2: with pipe
• Cable insulation material: Silicone
• Temperature range from [°C]: -25
• Temperature range to [°C]: +140
• Plug housing design: Plug sleeve housing
• SVHC: No SVHC present!
• Name: Kaabli remondikomplekt, tagatuli
• Manufacturer: HBE

• Engine Code: AJM
• Housing Type: without housing
• Voltage [V]: 12
• Quality class: PJ
• Name: Air flow sensor

Manufacturer: DENCKERMANN ELEKTRONIKA CEWKI CZUJNIKI

• Number of connectors: 4
• Weight [kg]: 0.03
• for OE number: 038 906 051
• Manufacturer: FEBI BILSTEIN

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Vehicle Identification Number (VIN) to: 1J-X-250 000
• Installatsiooni sügavus (mm): 20
• Ühenduste arv: 4
• Manufacturer: BERU