• Transmission Type: 6-Speed Dual-Clutch Transmission
• Filter type: Filter Insert
• Supplementary Article/Supplementary Info: with seal
• Width [mm]: 58
• Height [mm]: 105
• Transmission Code: DQ250
• Manufacturer: KAMOKA FILTRY

• Height [mm]: 106
• Outer Diameter [mm]: 58
• Vehicle Equipment: for vehicles with direct shift transmission
• Filter type: Filter Insert
• Supplementary Article/Info 2: with seal ring
• See accessories list for additionally required parts:
• Fabrication Number: FSF-AU-012

Transmission Type: 6-Speed Automatic Transmission, Dual-Clutch Transmission

• Transmission Type: 4-Speed Automatic Transmission
• Filter type: Filter Insert
• Supplementary Article/Supplementary Info: with seal
• Supplementary Article/Info 2: with oil sump gasket
• Width [mm]: 157
• Height [mm]: 32
• Seal Diameter [mm]: 34
• Transmission Code: AG4, JF404E
• Manufacturer: KAMOKA

• Engine Code: BML, BFH
• Transmission Type: 6-Speed Dual-Clutch Transmission
• Filter type: Filter Insert
• Outer Diameter [mm]: 58, 56
• for OE number: 02E 305 051 C
• Supplementary Article/Supplementary Info: with seal
• Name: Hdraulikafilter,automaatk„igukast
• Manufacturer: MAX

• Filter type: Filter Insert
• Manufacturer: JAPKO

• Filter type: Filter Insert
• Diameter [mm]: 58
• Height [mm]: 106
• Inner Diameter [mm]: 17
• Transmission Type: Automatic Transmission
• Supplementary Article/Supplementary Info: Incl. Gasket Set
• Quality class: PJ
• Name: Automatic transmission filter

• Filter type: Filter Insert
• Transmission Type: 6-Speed Automatic Transmission
• Height [mm]: 106
• Outer Diameter [mm]: 58
• Vehicle Equipment: for vehicles with direct shift transmission
• Supplementary Article/Info 2: with seal ring
• Manufacturer: AIC

General Information: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.

• Filter type: Screen Filter
• Manufacturer: JAPKO

• Vehicle Equipment: for vehicles with direct shift transmission
• Transmission Type: 6-Speed Automatic Transmission
• Transmission Code: DQ250
• Filter type: with filter heating
• Supplementary Article/Info 2: with seal ring
• Manufacturer: METZGER

• Fitting Position: Rear Axle
• Height [mm]: 40
• Outer Diameter [mm]: 55
• Supplementary Article/Supplementary Info: with accessories
• Clutch Type: for wet clutch
• Filter type: with housing cover, Filter Insert
• Supplementary Article/Info 2: with seal ring
• Clutch ID: HALDEX GEN I / 1
• See accessories list for additionally required parts:
• Fabrication Number: FHO-VW-000
• Manufacturer: NTY
• Name: NTY FHO-VW-000

• Engine Code: BML, BFH
• Transmission Type: 6-Speed Dual-Clutch Transmission
• Filter type: Filter Insert
• Length [mm]: 105
• Outer Diameter [mm]: 58, 56
• Weight [kg]: 0.08
• Manufacturer: BLUEPRINT

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Engine Code: BML, BFH
• Transmission Type: 6-Speed Dual-Clutch Transmission
• Length [mm]: 105.4
• Weight [kg]: 0.1
• Outer Diameter [mm]: 58, 55.5
• Filter type: Filter Insert
• Manufacturer: DRIVE

• Transmission Code: DQ 250
• Filter type: Filter Insert
• Height [mm]: 106
• Outer Diameter [mm]: 58
• Inner Diameter 1 [mm]: 55
• Inner Diameter 2 [mm]: 17.5
• Name: HšDRAULIKAFILTER,AUTOMAATKŽIGUKAST
• Manufacturer: ALC

Transmission Type: 6-Speed Automatic Transmission, Dual-Clutch Transmission

• Transmission Type: Automatic Transmission
• Filter type: Filter Insert
• Diameter [mm]: 58.1
• Height [mm]: 106.1
• Inner Diameter 2 [mm]: 17
• Packaging height [cm]: 13.1
• Packaging length [cm]: 7
• Packaging width [cm]: 7
• Net Weight [g]: 74
• Manufacturer: KNECHT
• Name: KN HX132D
• Lisainfo: HX 132D MAH
• Additional information: HX 132D MAH

• Transmission Type: 6-Speed Dual-Clutch Transmission
• Supplementary Article/Supplementary Info: with seal
• Quantity Unit: Piece
• Transmission Code: DQ250
• Filter type: Filter Insert
• Name: HšDRAULIKAFILTER,AUTOMAATKŽIGUKAST
• Manufacturer: MEY

• Engine Code: BML, BFH
• Transmission Type: 6-Speed Dual-Clutch Transmission
• Filter type: Filter Insert
• Length [mm]: 105.4
• Outer Diameter [mm]: 58, 55.5
• Weight [kg]: 0.08
• Name: HšDRAULIKAFILTER,AUTOMAATKŽIGUKAST
• Manufacturer: FEB
• Additional information: FE44176
• Lisainfo: FE44176

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Engine Code: BML, BFH
• Transmission Type: 6-Speed Dual-Clutch Transmission
• Filter type: Filter Insert
• Length [mm]: 105.4
• Outer Diameter [mm]: 58, 55.5
• Weight [kg]: 0.08
• Manufacturer: SWAG
• Lisainfo: 30 94 4176 SWA
• Additional information: 30 94 4176 SWA

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Fabrication Number: FSF-AU-011
• Manufacturer: NTY
• Name: NTY FSF-AU-011

• Filter type: Screen Filter
• Manufacturer: JAPKO

• Filter type: Pre-Filter
• Transmission Code: DQ250
• Model Year to: 2004
• Vehicle Equipment: for vehicles with direct shift transmission
• Supplementary Article/Supplementary Info: without gasket/seal
• Name: Hdraulikafilter,automaatk„igukast
• Manufacturer: MAX

Transmission Type: 6-Speed Automatic Transmission, Dual-Clutch Transmission

Manufacturer: METALCAUCHO

• Height [mm]: 69
• Outer Diameter [mm]: 56
• External Thread Size: M48 x 2
• Supplementary Article/Info 2: with lid, with cap
• Fitting Position: Rear Axle
• Gasket inner diameter: 44.5
• Seal Ring Outer Diameter: 50.5
• Weight [kg]: 0.07
• Supplementary Article/Supplementary Info: for multi-plate clutch
• Manufacturer: FEB

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions. Name: Hdraulikafilter, t„isveoga soiduki mitme kettaga sidur

• Transmission Code: 02E, 0D9, DQ250
• Supplementary Article/Info 2: with seal ring
• See accessories list for additionally required parts:
• Height [mm]: 106
• Outer Diameter [mm]: 58
• Filter type: Filter Insert
• Vehicle Equipment: for vehicles with direct shift transmission
• Weight [kg]: 0.1
• Recommended change interval [km]: 60,000
• Recommended change interval [years]: 5
• Manufacturer: VAICO
• Lisainfo: V10-0440 VAI
• Additional information: V10-0440 VAI

Transmission Type: 6-Speed Automatic Transmission, Dual-Clutch Transmission General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Transmission Code: 02E, 0D9, DQ250
• Outer Diameter [mm]: 58
• Height [mm]: 106
• Vehicle Equipment: for vehicles with direct shift transmission
• Supplementary Article/Info 2: with seal ring
• See accessories list for additionally required parts:
• Weight [kg]: 0.111
• Filter type: Filter Insert
• Recommended change interval [km]: 60,000
• Recommended change interval [years]: 5
• Manufacturer: VAICO
• Quality class: PJ
• Name: Automatic transmission filter

Transmission Type: 6-Speed Automatic Transmission, Dual-Clutch Transmission General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Transmission Type: 5-Speed Automatic Transmission
• Supplementary Article/Supplementary Info: without gasket/seal
• Quantity Unit: Piece
• Transmission Code: JF506E
• Filter type: Screen Filter
• Name: HšDRAULIKAFILTER,AUTOMAATKŽIGUKAST
• Manufacturer: MEY

• Filter type: Pre-Filter
• Model Year from: 2005
• Transmission Code: DQ250
• Vehicle Equipment: for vehicles with direct shift transmission
• Supplementary Article/Supplementary Info: without gasket/seal
• Name: Hdraulikafilter,automaatk„igukast
• Manufacturer: MAX

Transmission Type: 6-Speed Automatic Transmission, Dual-Clutch Transmission

• Height [mm]: 69
• Outer Diameter [mm]: 56
• External Thread Size: M48 x 2
• Supplementary Article/Info 2: with lid, with cap
• Fitting Position: Rear Axle
• Gasket inner diameter: 44.5
• Seal Ring Outer Diameter: 50.5
• Weight [kg]: 0.07
• Supplementary Article/Supplementary Info: for multi-plate clutch
• Manufacturer: BLUE PRINT

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

Fabrication Number: FHO-VW-003

• Engine Code: BFH
• Transmission Code: Jatco 09A
• Transmission Type: 5-Speed Automatic Transmission
• Filter type: Screen Filter
• Manufacturer: JAPKO

• Transmission Type: 6-Speed Automatic Transmission
• Transmission Code: DQ250
• Vehicle Equipment: for vehicles with direct shift transmission
• Filter type: Screen Filter
• Manufacturer: ASHIKA

• Filter type: Screen Filter
• Manufacturer: JAPKO

• Transmission Type: 6-Speed Automatic Transmission
• Transmission Code: DQ250
• Vehicle Equipment: for vehicles with direct shift transmission
• Filter type: Screen Filter
• Manufacturer: JAPKO

• Transmission Code: AG4
• Transmission Type: Automatic Transmission
• Filter type: Filter Insert
• Supplementary Article/Info 2: with oil sump gasket
• Length [mm]: 196
• Width [mm]: 158
• Height [mm]: 34
• Inner Diameter [mm]: 25
• SVHC: No SVHC present!
• Name: HšDRAULIKAFILTER,AUTOMAATKŽIGUKAST
• Manufacturer: MAN

• Recommended change interval [years]: 3
• Clutch Type: for wet clutch
• Clutch ID: HALDEX GEN I / 1
• Recommended change interval [km]: 30,000
• Supplementary Article/Supplementary Info: with accessories
• Filter type: with housing cover, Filter Insert
• Height [mm]: 40
• Fitting Position: Rear Axle
• Outer Diameter [mm]: 55
• See accessories list for additionally required parts:
• Supplementary Article/Info 2: with seal ring
• Weight [kg]: 0.088
• Manufacturer: VAICO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Vehicle Equipment: for vehicles with power steering
• Diameter [mm]: 12
• Filter type: In-Line Filter
• Supplementary Article/Info 2: Magnetic
• Manufacturer: JP GROUP
• Lisainfo: Hydraulic Filter, steering system
• Additional information: Hydraulic Filter, steering system

• Engine Code: BML, BFH
• Transmission Type: 6-Speed Dual-Clutch Transmission
• Filter type: Screen Filter
• Length [mm]: 235
• Width [mm]: 165
• Height [mm]: 65
• Weight [kg]: 0.25
• Manufacturer: FEBI BILSTEIN

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Engine Code: BML, BFH
• Transmission Type: 6-Speed Dual-Clutch Transmission
• Filter type: Screen Filter
• Length [mm]: 235
• Width [mm]: 165
• Height [mm]: 65
• Weight [kg]: 0.25
• Name: SW 33 10 2944
• Manufacturer: SWAG

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Vehicle Equipment: for vehicles with power steering
• Diameter [mm]: 10
• Filter type: In-Line Filter
• Supplementary Article/Info 2: Magnetic
• Manufacturer: JP GROUP
• Lisainfo: Hydraulic Filter, steering system
• Additional information: Hydraulic Filter, steering system

• Transmission Code: DQ250
• Fitting Position: inner
• Filter type: Pre-Filter, Filter Insert
• Model Year to: 2004
• See accessories list for additionally required parts:
• Vehicle Equipment: for vehicles with direct shift transmission
• Weight [kg]: 0.431
• Recommended change interval [km]: 60,000
• Recommended change interval [years]: 5
• Manufacturer: VAICO

Transmission Type: 6-Speed Automatic Transmission, Dual-Clutch Transmission General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Engine Code: BML, BFH
• Transmission Type: 6-Speed Dual-Clutch Transmission
• Filter type: Screen Filter
• Length [mm]: 235
• Width [mm]: 165
• Height [mm]: 65
• Weight [kg]: 0.25
• Name: Hdraulikafilter,automaatk„igukast
• Manufacturer: BLP

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Model Year from: 2005
• See accessories list for additionally required parts:
• Transmission Code: DQ250
• Fitting Position: inner
• Vehicle Equipment: for vehicles with direct shift transmission
• Filter type: Pre-Filter, Filter Insert
• Weight [kg]: 0.431
• Recommended change interval [km]: 60,000
• Recommended change interval [years]: 5
• Manufacturer: VAICO

Transmission Type: 6-Speed Automatic Transmission, Dual-Clutch Transmission General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.