Tootekategooriad
Filtrid Pidurid vedrustus/alusvanker Roolisüsteem Jahutus/kliima Elektrisüsteem Veokonks/lisad Jõuülekanne Väljalaskesüsteem Kere Süüte-/eelsüütesüsteem Mootor Klaasid/klaasipuhastus Valgustus Kütus Kabiinivarustus HooldusToode
Kirjeldus
Laoseis
Hind
(km-ga)
- Spetsifikatsioon DOT järgi: DOT 4
- keem.omadus: sünteetiline
- Maht(liiter): 1
- Kuivkeemispunkt (°C): 245
- Konteineri tüüp: Pudel
-
Lisainfo: 36-
0048
- Spetsifikatsioon DOT järgi: DOT 4
- keem.omadus: sünteetiline
- Maht(liiter): 3
- Kuivkeemispunkt (°C): 245
- Konteineri tüüp: Kanister
-
Lisainfo: 36-
0049
3 Liitrit
- Kogus pakendis: 24
- Spetsifikatsioon DOT järgi: DOT 4
- Keemispunkt (°C): 180
- Kuivkeemispunkt (°C): 260
- DIN/ISO: ISO 4925
-
Maht(liiter): 0,
25 - Spetsifikatsioon: MB 331.0
-
Kaal (kg): 0,
301 - Hooldusinfot jälgida:
- Tootja: FEBI BILSTEIN
- Lisainfo: FE26748
Üldine informatsioon: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.
- Spetsifikatsioon DOT järgi: DOT 4
- keem.omadus: sünteetiline
-
Maht(liiter): 0,
5 - Kuivkeemispunkt (°C): 245
- Konteineri tüüp: Pudel
- Tootja: VALEO
- Kogus pakendis: 24
- Kuivkeemispunkt (°C): 260
- Spetsifikatsioon DOT järgi: DOT 4
- Keemispunkt (°C): 180
- DIN/ISO: ISO 4925
-
Maht(liiter): 0,
5 - Spetsifikatsioon: MB 331.0
-
Kaal (kg): 1,
139 - Hooldusinfot jälgida:
- Tootja: FEBI
Üldine informatsioon: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.
- Spetsifikatsioon DOT järgi: DOT 4+
- Kuivkeemispunkt (°C): 265
- Keemispunkt (°C): 180
-
Spetsifikatsioon: FMVSS 116 DOT 4,
SAE J 1703 / J 1704 - keem.omadus: sünteetiline
- Soovituslik vahetusintervall (aastad): 2
- Konteineri tüüp: Pudel
-
Maht(liiter): 0,
25 - jälgida süsteemi mahutavust:
- Jälgige sõidukitootja juhiseid:
-
Kaal (kg): 0,
28 - Kõrgus (mm): 50
- Laius (mm): 45
- Pikkus (mm): 70
- Soovituslik vahetusintervall (km): 40 000
- DIN/ISO: ISO 4925
- Tootja: VAICO
Üldine informatsioon: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.
- Spetsifikatsioon DOT järgi: DOT 4
- keem.omadus: sünteetiline
- Maht(liiter): 1
- Kuivkeemispunkt (°C): 245
- Konteineri tüüp: Pudel
-
Kaal (kg): 1,
15 - Tootja: VALEO
- Keemispunkt (°C): 170
- Kuivkeemispunkt (°C): 265
-
Spetsifikatsioon DOT järgi: DOT 4,
DOT 3, DOT 4 LV - Konteineri tüüp: Pudel
- Soovituslik vahetusintervall (aastad): 2
- Soovituslik vahetusintervall (km): 40 000
-
Maht(liiter): 0,
5 -
Viskoossusklass SAE: J 1703 /
J 1704 - Hooldusinfot jälgida:
- Tootja: VAICO
Hüdraulikavedeliku tootja soovitus: W TL 766-Z, VW 50 114, BMW QV 34 001, GM Europa GMW 3356, PSA STL S71 2114, Ford WSS-M6C65-A2 DIN/ISO: ISO 4925 Class 3, ISO 4925 Class 4, ISO 4925 Class 6 Üldine informatsioon: Products supplied by us are without exception intended for the designated use. Please note that our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist personnel. There is no guarantee for inappropriate, improper or unintended use.
- Kuivkeemispunkt (°C): 260
- Keemispunkt (°C): 180
- Spetsifikatsioon DOT järgi: DOT 4
- DIN/ISO: ISO 4925
- Maht(liiter): 1
- Spetsifikatsioon: MB 331.0
-
Kaal (kg): 1,
139 - Hooldusinfot jälgida:
- Tootja: FEBI BILSTEIN
- Lisainfo: FE23930
Üldine informatsioon: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.
- Keemispunkt (°C): 155
- Spetsifikatsioon DOT järgi: DOT 4
- Kuivkeemispunkt (°C): 260
- keem.omadus: sünteetiline
-
Maht(liiter): 0,
5 - Soovituslik vahetusintervall (aastad): 2
- jälgida süsteemi mahutavust:
- Jälgige sõidukitootja juhiseid:
- Kõrgus (mm): 174
- Konteineri tüüp: Pudel
-
DIN/ISO: ISO 4925 Class 4,
ISO 4925 - Laius (mm): 58
-
Kaal (kg): 0,
6, 0, 858 -
Spetsifikatsioon: FMVSS 116 DOT 4,
SAE J 1703 F - Pikkus (mm): 95
- Soovituslik vahetusintervall (km): 40 000
- Tootja: VAICO
Üldine informatsioon: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.
- Spetsifikatsioon DOT järgi: DOT 4+
- keem.omadus: sünteetiline
- Maht(liiter): 1
- Kuivkeemispunkt (°C): 265
- Konteineri tüüp: Pudel
-
Kaal (kg): 1,
13 - Tootja: VALEO
- Nimetus: VA 402406
- Spetsifikatsioon DOT järgi: DOT 4+
- Kuivkeemispunkt (°C): 265
- Keemispunkt (°C): 180
- keem.omadus: sünteetiline
- Konteineri tüüp: Pudel
- Soovituslik vahetusintervall (aastad): 2
- Maht(liiter): 1
- Soovituslik vahetusintervall (km): 40 000
- Jälgige sõidukitootja juhiseid:
- jälgida süsteemi mahutavust:
- Pikkus (mm): 60
-
Kaal (kg): 1,
15, 1, 4 - Kõrgus (mm): 225
- Laius (mm): 115
- DIN/ISO: ISO 4925
- Tootja: VAICO
Spetsifikatsioon: FMVSS 116 DOT 4, ISO 4925 Class 4, SAE J 1703 / J 1704, FMVSS 116 DOT 3 Üldine informatsioon: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.
- Spetsifikatsioon DOT järgi: DOT 4
- keem.omadus: sünteetiline
- Maht(liiter): 5
- Kuivkeemispunkt (°C): 245
- Konteineri tüüp: Kanister
- Tootja: VALEO
- Kogus pakendis: 4
- Keemispunkt (°C): 180
- Spetsifikatsioon DOT järgi: DOT 4
- Kuivkeemispunkt (°C): 260
- DIN/ISO: ISO 4925
- Maht(liiter): 5
- Spetsifikatsioon: MB 331.0
-
Kaal (kg): 5,
607 - Hooldusinfot jälgida:
- Tootja: FEBI BILSTEIN
Üldine informatsioon: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.
- Spetsifikatsioon DOT järgi: DOT 4+
- Kuivkeemispunkt (°C): 265
- Keemispunkt (°C): 180
- keem.omadus: sünteetiline
- Maht(liiter): 5
- Soovituslik vahetusintervall (aastad): 2
- Konteineri tüüp: Kanister
- Soovituslik vahetusintervall (km): 40 000
- Jälgige sõidukitootja juhiseid:
- jälgida süsteemi mahutavust:
- Laius (mm): 115
- Pikkus (mm): 300
- Kõrgus (mm): 230
-
Kaal (kg): 4,
72 - DIN/ISO: ISO 4925
- Tootja: VAICO
Spetsifikatsioon: ISO 4925 Class 4, SAE J 1703 / J 1704, FMVSS 116 DOT 3, FMVSS 116 DOT 4 Üldine informatsioon: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.
-
Mahutavus [l]: 0,
45 - Spetsifikatsioon DOT järgi: DOT 4
Spetsifikatsioon: BMW/Mini 83 13 0 139, FMVSS 116 DOT 4, ISO 4925 class 6, Saab 93165410, SAE J1704, VW 501.14
-
Mahutavus [l]: 0,
45 -
Spetsifikatsioon: FMVSS 116 DOT 4,
ISO 4925 class 4 - Spetsifikatsioon DOT järgi: DOT 4
Laki Auto universaaltooted
TecDoc sõidukite kataloog
TecDoc veokite kataloog