• Switch point from [bar]: 0.15
• Switch point to [bar]: 0.35
• Colour Coding: blue
• Number of connectors: 1
• External Thread [mm]: M10x1
• Tootja: JP GROUP
• Lisainfo: PAKENDIS 10 tk

• Kerenumber (VIN) alates: 8C-N-000 001
• Kerenumber (VIN) kuni: 8C-N-300 000
• Sõidukivarustus: Kliimaseadmega sõidukile
• Thread Size: M10x1
• Colour: grey
• Number of pins: 1
• Spanner Size: 24
• Tootja: DELLO AUTOMEGA

• Thread Size: M10x1
• Length [mm]: 46
• Spanner Size: 24
• Colour Coding: white
• Number of pins: 1
• Tootja: DELLO AUTOMEGA

• Plug Type: Blade Terminal
• Operating Mode: Hydraulic
• Colour Coding: brown
• Thread Size: M 10
• Thread Pitch [mm]: 1
• Number of pins: 1
• Supplementary Article/Info 2: with seal ring
• Shifting Points [bar]: 0.3
• Tootja: TOPRAN HANS PRIES

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Plug Type: Blade Terminal
• Operating Mode: Hydraulic
• Colour Coding: grey
• Thread Size: M 10
• Thread Pitch [mm]: 1
• Number of pins: 1
• Control Range [bar]: 0,75 - 1,05
• Supplementary Article/Info 2: with seal ring
• Tootja: TOPRAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Switch point from [bar]: 1.6
• Switch point to [bar]: 2
• Tootja: JP GROUP
• Lisainfo: PAKENDIS 10 tk

• Mootorikood: 1Z
• Värv: sinine
• Pressure [bar]: 0.3
• Thread Size: M10x1
• Spanner Size: 24
• Nimetus: EP 1.800.108
• Tootja: EPS
• Lisainfo: 1-800-108

• Plug Type: Blade Terminal
• Operating Mode: Hydraulic
• Colour Coding: blue
• Thread Size: M 10
• Thread Pitch [mm]: 1
• Number of pins: 1
• Control Range [bar]: 0,15 - 0,35
• Tootja: TOPRAN
• Lisainfo: 100 345 HP

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Mootorikood: 1Z
• Värv: sinine
• Pressure [bar]: 0.3
• Thread Size: M10x1
• Spanner Size: 24
• Tootja: FACET

• Thread Size: M 10x1
• Housing Colour: black
• Pressure [bar]: 0.4
• Tootja: FAE

• Hulk: 1
• Surface: Zinc-coated
• Control Range [bar]: 0,15 - 0,35
• Weight [kg]: 0.031
• Required quantity: 1
• External Thread [mm]: M10 x 1
• Number of connectors: 1
• Thread Length [mm]: 13
• Inner Diameter [mm]: 2.54
• Spanner Size: 24
• Supplementary Article/Info 2: with seal ring
• Colour Coding: blue
• Length [mm]: 46
• General Information: Oil pressure sensor
• Tootja: VIKA

• Switch point from [bar]: 0.75
• Switch point to [bar]: 1.05
• External Thread [mm]: M10x1
• Number of connectors: 1
• Colour Coding: grey
• Lisainfo: PAKENDIS 10 tk

• Length [mm]: 46
• Switch point from [bar]: 0.15
• Switch point to [bar]: 0.35
• Inner Diameter [mm]: 2.54
• External Thread Size: M10 x 1
• Thread Length [mm]: 13
• Spanner Size: 24
• Number of connectors: 1
• Colour Coding: blue
• Surface: Zinc-coated
• Weight [kg]: 0.031
• Supplementary Article/Info 2: with seal ring
• Tootja: FEBI BILSTEIN

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• for OE number: 068 919 081 A
• Thread Size: M10 x 1
• Colour: grey
• Switch point from [bar]: 0.75
• Switch point to [bar]: 1.05
• Tootja: TRUCKTEC

• for OE number: 028 919 081 D
• Thread Size: M10 x 1
• Colour: blue
• Switch point from [bar]: 0.15
• Switch point to [bar]: 0.35
• Tootja: TRUCKTEC

• Thread Size: M 10x1
• Housing Colour: white
• Pressure [bar]: 0.9
• Tootja: FAE ELEKTRYKA

• Thread Size: M 10x1
• Housing Colour: white
• Pressure [bar]: 1.8
• Tootja: FAE

• Length [mm]: 46
• Switch point from [bar]: 0.15
• Switch point to [bar]: 0.35
• Inner Diameter [mm]: 2.54
• External Thread Size: M10 x 1
• Thread Length [mm]: 13
• Spanner Size: 24
• Number of connectors: 1
• Colour Coding: blue
• Surface: Zinc-coated
• Weight [kg]: 0.031
• Supplementary Article/Info 2: with seal ring
• Nimetus: SW 30 23 0002
• Tootja: SWAG

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Pressure [bar]: 3.5
• Housing Colour: blue
• Thread Size: M10×1.6
• Diameter [mm]: 24
• Spanner Size: 24
• Number of pins: 1
• Tootja: DELPHI
• Nimetus: DE SW90009
• Lisainfo: SW90009

• Length [mm]: 46
• Switch point from [bar]: 1.6
• Switch point to [bar]: 2
• External Thread Size: M10 x 1
• Thread Length [mm]: 13
• Spanner Size: 24
• Number of connectors: 1
• Colour Coding: white
• Surface: Zinc-coated
• Weight [kg]: 0.03
• Supplementary Article/Info 2: with seal ring
• Tootja: FEBI BILSTEIN

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Pressure [bar]: 1.8
• Thread Size: M10 x 1
• Number of pins: 1
• Technical Information Number: circuit N.O.
• Tootja: ERA

• Switch Pressure [bar]: 0.3
• Thread Size: M10x1.0
• Sensor Type: Closed-type Sensor
• Tootja: VERNET

• Switch Pressure [bar]: 0.9
• Thread Size: M10x1.0
• Sensor Type: Open-style sensor
• Tootja: VERNET

• Switch point from [bar]: 1.6
• Length [mm]: 46
• Switch point to [bar]: 2
• External Thread Size: M10 x 1
• Thread Length [mm]: 13
• Spanner Size: 24
• Number of connectors: 1
• Colour Coding: white
• Surface: Zinc-coated
• Weight [kg]: 0.03
• Supplementary Article/Info 2: with seal ring
• Nimetus: SW 30 23 0001
• Tootja: SWAG

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Colour: blue
• Shifting Points [bar]: 0.25
• Tootja: AIC

General Information: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.

• Colour: grey
• Pressure [bar]: 0.9
• Tootja: AIC

General Information: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.

• Colour: white
• Pressure [bar]: 1.8
• Tootja: AIC

General Information: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.

• Pressure [bar]: 0.3
• Thread Size: M10 x 1
• Technical Information Number: circuit N.C.
• Tootja: ERA

• Thread Size: M10 x 1
• Spanner Size: 14
• Supplementary Article/Supplementary Info: with gasket/seal
• Number of pins: 1
• Colour Coding: blue
• Tootja: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Mootorikood: 1Z
• Värv: hall
• Pressure [bar]: 0.9
• Thread Size: M10x1
• Spanner Size: 24
• Corresponds to the original part in colour: brown
• Nimetus: EP 1.800.095
• Tootja: EPS

• Mootorikood: 1Z
• Värv: hall
• Pressure [bar]: 0.9
• Thread Size: M10x1
• Spanner Size: 24
• Corresponds to the original part in colour: brown
• Tootja: FACET

• Pressure [bar]: 1.4
• Thread Size: M10 x 1
• Technical Information Number: circuit N.O.
• Tootja: ERA

• Pressure [bar]: 0.9
• Thread Size: M10 x 1
• Technical Information Number: circuit N.O.
• Tootja: ERA

• Thread Size: M 10x1
• Colour: brown
• Spanner Size: 24
• Number of pins: 1
• Supplementary Article/Info 2: with seal ring
• Pressure [bar]: 0.25
• Tootja: AIC

General Information: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.

• Length [mm]: 46
• Switch point from [bar]: 0.75
• Switch point to [bar]: 1.05
• Inner Diameter [mm]: 2.48
• External Thread Size: M10 x 1
• Thread Length [mm]: 13
• Spanner Size: 24
• Number of connectors: 1
• Colour Coding: grey
• Shifting Points [bar]: 0.7
• Surface: Zinc-coated
• Weight [kg]: 0.031
• Supplementary Article/Info 2: with seal ring
• Tootja: FEBI BILSTEIN

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Thread Size: M10x1,0
• Colour: white
• Pressure from [bar]: 1.6
• Pressure to [bar]: 2
• Tootja: VEMO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Number of pins: 1
• Pressure [bar]: 0.3
• Tootja: AIC

General Information: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.

• Length [mm]: 46
• Switch point from [bar]: 0.75
• Switch point to [bar]: 1.05
• Inner Diameter [mm]: 2.48
• External Thread Size: M10 x 1
• Thread Length [mm]: 13
• Spanner Size: 24
• Number of connectors: 1
• Colour Coding: grey
• Shifting Points [bar]: 0.7
• Surface: Zinc-coated
• Weight [kg]: 0.031
• Supplementary Article/Info 2: with seal ring
• Nimetus: SW 30 23 0004
• Tootja: SWAG

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Supplementary Article/Supplementary Info: with gasket/seal
• Thread Size: M10x1,0
• Control Range [bar]: 0,15 - 0,35
• Colour: blue
• Tootja: VEMO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Voltage [V]: 12
• Combi Switch Function: Normally Closed Contact
• Current Strength [A]: 0.25
• Thread Size: M10x1
• Spanner Size: 24
• Pressure from [bar]: 0.15
• Pressure to [bar]: 0.35
• Number of pins: 1
• Plug Type: Blade Terminal
• Corresponds to the original part in colour: blue
• Assy./disassy. by qualified personnel required!:
• SVHC: 7439-92-1; Lead
• Tootja: HELLA
• Nimetus: HE 6ZL003259641

• Mootorikood: 1Z
• Pistikkontaktide arv: 1
• Korpusevärv: sinine
• Thread Size: M10x1
• Spanner Size: 13
• Corresponds to the original part in colour: blue
• Nimetus: EP 1.830.093
• Tootja: EPS

• Tightening torque from [Nm]: 20
• Voltage [V]: 12
• Combi Switch Function: Normally Open Contact
• Current Strength [A]: 0.25
• Tolerance [%]: 15
• Thread Size: M10x1
• Spanner Size: 24
• Pressure from [bar]: 1.6
• Pressure to [bar]: 2
• Number of pins: 1
• Corresponds to the original part in colour: Milk White
• Assy./disassy. by qualified personnel required!:
• Nimetus: HE 6ZL003259441
• Tootja: HELLA

• Tightening torque from [Nm]: 20
• Voltage [V]: 12
• Combi Switch Function: Normally Open Contact
• Current Strength [A]: 0.25
• Tolerance [%]: 15
• Thread Size: M10x1
• Spanner Size: 24
• Pressure from [bar]: 1.2
• Pressure to [bar]: 1.6
• Number of pins: 1
• Plug Type: Blade Terminal
• Corresponds to the original part in colour: black
• Assy./disassy. by qualified personnel required!:
• Tootja: HELLA
• Nimetus: HE 6ZL003259471

• Ehitusaasta kuni: 07.1995
• Tehnilisi andmeid jälgida:
• Tootja: BOSCH

• External Thread Size: M10 x 1
• Number of connectors: 1
• Weight [kg]: 0.01
• Supplementary Article/Info 2: with seal ring
• Tootja: FEBI BILSTEIN

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• External Thread Size: M10 x 1
• Number of connectors: 1
• Weight [kg]: 0.01
• Supplementary Article/Info 2: with seal ring
• Nimetus: SW 30 93 3825
• Tootja: SWAG

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Thread Size: M10x1
• Tootja: FAE