• Installatsiooni pool: esisild vasakul, esisild paremal
• Välisläbimõõt [mm]: 74
• Siseläbimõõt [mm]: 40
• Laius (mm): 40
• Lisainfo: Wheel bearing, front

• Installatsiooni pool: Esisild
• Siseläbimõõt [mm]: 40
• Välisläbimõõt [mm]: 74
• Kõrgus (mm): 39,9
• Tootja: JP GROUP
• Lisainfo: Wheel bearing kit, for one front wheel

• Installatsiooni pool: Tagasild vasakul, Tagasild paremal
• Piirangutega toode/piirangu info 2: koos integreeritud rattalaagriga
• Veljeaukude hulk: 5
• Lisainfo: Wheel hub with bearing, rear

• Nimetus: GH 394710
• Tootja: AUTO-GH

• Installatsiooni pool: Tagasild
• Hammastehulk ABS-rõngas: 43
• Siseläbimõõt [mm]: 61
• Välisläbimõõt [mm]: 79,5
• Piirangutega toode/piirangu info 2: rattalaagri/keskme jaoks
• Laius (mm): 21
• Nimetus: PIER—CIEã CZUJNIKA ABS VW
• Tootja: VMO

Üldine informatsioon: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Supplementary Article/Info 2: for wheel bearing/wheel hub
• Fitting Position: Rear Axle Left, Rear Axle Right
• Tootja: METZGER

• Kerenumber (VIN): [;6H-X-027500], [;6K-X-290 000], [;6NXY379991]
• Installatsiooni pool: paremal, vasakul, Tagasild
• Inner Diameter 1 [mm]: 17
• Outer Diameter 2 [mm]: 50
• Outer Diameter 1 [mm]: 39
• Width 1 [mm]: 13
• Width 2 [mm]: 14
• Tootja: SNR
• Nimetus: SN R154.13

• Fitting Position: Front Axle Left, Front Axle Right
• Width [mm]: 40
• Outer Diameter [mm]: 74
• Inner Diameter [mm]: 40
• Number of Parts [parts]: 6
• Assy./disassy. by qualified personnel required!:
• Nimetus: AB 141-03-002
• Tootja: ABAKUS

General Information: The following information is for general and informational purposes only and does not constitute warranty terms. Warranty terms and conditions are available from our dealers and in our general terms and conditions of sale. Abakus spare/repair parts are intended only for vehicle repairs in order to restore their original functionality. Abakus spare/repair parts are used or sold to users only for the purpose of repairing vehicles to restore their original look and functionality and are not original/genuine/OE/OEM/OES replacement parts. These items do not originate from the vehicle manufacturer and may be the subject of a design not owned by Abakus and the manufacturer of this spare part. They may only be used for repairs to restore the intended vehicle to its original appearance. Our products are delivered without instruction of installation. Installation of our product may only be carried out by trained specialist technicians in specific car repairs. Products supplied by us are exclusively intended for proper and appropriate use. The warranty may become invalid in the event of: improper installation or repair, unsuitable application or use, installation or repair made outside specialist car workshops. Warranty claims are lost if the vehicle is modified and used for motor sports, tuning or similar events (except our tuning parts which are described in TecDoc and on our price list). Warranty application should include complete documentation among others: chassis no., first registration, vehicle mileage, information about LPG installation, fault memory log, pictures, our QC (quality check) code, installation invoice, contact details of the car repair workshop performing the replacement or repair. Warranty application are available in our Client Panel system. Complaints may require supplementing data such as error memory logs. Incomplete documentation may result in rejection of the claim. Any damage caused during transport is not considered quality damage and will be considered on an individual basis. The product is intended for use within the performance limits specified by the manufacturer and should only be used by qualified personnel who have been trained to operate this product. Before each use, the product should be checked for damage or fixing of its parts and not used if any defects or loose parts are found. Failure to follow the manufacturer's guidelines could result in potential product damage or even injury. Wear appropriate protective clothing if necessary when working with the product.

• Installatsiooni pool: Esisild
• Laius (mm): 40
• Siseläbimõõt [mm]: 40
• Välisläbimõõt [mm]: 74
• Nimetus: RATTALAAGRIKOMPLEKT
• Tootja: MAX

• Installatsiooni pool: Esisild
• Width [mm]: 40
• Inner Diameter [mm]: 40
• Outer Diameter [mm]: 74
• Kvaliteediklass: PJ
• Nimetus: Wheel bearing kit

• Installatsiooni pool: esisild mõlemapoolselt
• Hulk telje kohta: 2
• Siseläbimõõt [mm]: 40
• Laius (mm): 40
• Välisläbimõõt [mm]: 74
• Tootja: TOPRAN

Üldine informatsioon: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Fitting Position: Rear Axle
• Guarantee: 4 years guarantee
• Weight [kg]: 1
• Number of Holes: 4
• Always compare old and new part (in particular OE No.):
• Nimetus: CE 29SKV994
• Tootja: ESEN SKV

• Installatsiooni pool: Esisild
• Width [mm]: 40
• Inner Diameter [mm]: 40
• Outer Diameter [mm]: 74
• Tootja: DENCKERMANN ZAWIESZENIE

• Outer Diameter [mm]: 74
• Supplementary Article/Info 2: without wheel hub
• Fitting Position: Front Axle, Front Axle Left, Front Axle Right
• Fabrication Number: KLP-VW-009
• Tootja: NTY
• Nimetus: NTY KLP-VW-009

• Installatsiooni pool: Tagasild, Esisild
• Laius (mm): 40
• Siseläbimõõt [mm]: 40
• Välisläbimõõt [mm]: 74
• Tootja: DELLO AUTOMEGA

• alternatiivne remondikomplekt: 100 498 0048
• Installatsiooni pool: Esisild
• Siseläbimõõt [mm]: 40
• Välisläbimõõt [mm]: 74
• Kõrgus (mm): 39,9
• Laagriteostus: Kuullaager
• Nimetus: RATTALAAGER
• Tootja: MEY
• Lisainfo: 1004070048

• Installatsiooni pool: esisild mõlemapoolselt
• Fitting Position: Front Axle
• Width [mm]: 40
• Inner Diameter [mm]: 40
• Outer Diameter [mm]: 74
• Tootja: JPN

• Installatsiooni pool: esisild vasakul, esisild paremal
• Hulk telje kohta: 2
• Välisläbimõõt [mm]: 74
• Siseläbimõõt [mm]: 40
• Laius (mm): 40
• Piirangutega toode/piirangu info 2: koos mutriga, koos turvarõngaga
• Täiskomplekt:
• Tootja: TOPRAN

Üldine informatsioon: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Installatsiooni pool: esisild vasakul, esisild paremal
• Version: Two
• Width 1 [mm]: 40
• Outer Diameter 1 [mm]: 74
• Inner Diameter 1 [mm]: 40
• Tootja: GSP

• Installatsiooni pool: Esisild
• Piirangutega toode/piirangu info 2: ilma integreeritud ABS-sensorita
• Laius (mm): 40
• Välisläbimõõt [mm]: 74
• Siseläbimõõt [mm]: 40
• Tootja: FAI

• Installatsiooni pool: Esisild
• Laius (mm): 40
• Siseläbimõõt [mm]: 39,6
• Välisläbimõõt [mm]: 74
• Netokaal [kg]: 0,77
• Nimetus: RATTALAAGRIKOMPLEKT
• Tootja: NK
• Lisainfo: .

• Fabrication Number: KLP-MZ-012
• Rim Size [inch]: 18.0
• Tootja: NTY

Fitting Position: Rear Axle, Front Axle Left, Front Axle Right, Front Axle

• Installatsiooni pool: Esisild
• Laius (mm): 40
• Siseläbimõõt [mm]: 40
• Välisläbimõõt 1 [mm]: 74
• Tootja: METELLI LOZYSKA KOLA PIASTY

• Installatsiooni pool: Esisild
• vajaminev tükihulk: 2
• Tootja: DRIVE

• Installatsiooni pool: esisild vasakul, esisild paremal
• Version: One
• Width 1 [mm]: 40
• Outer Diameter 1 [mm]: 74
• Inner Diameter 1 [mm]: 40
• Tootja: GSP

• Fitting Position: Front Axle
• for OE number: 1J0 498 625
• Width [mm]: 40
• Outer Diameter [mm]: 74
• Tootja: KAMOKA PRZEGUBY PÓ£OSIE PIASTY

• Installatsiooni pool: Esisild
• Laius (mm): 40
• Siseläbimõõt [mm]: 40
• Välisläbimõõt [mm]: 74
• Laagriteostus: kuullaager
• Kaal (kg): 0,768
• Piirangutega toode/piirangu info: teljemutriga
• Piirangutega toode/piirangu info 2: koos turvarõngaga
• Nimetus: RATTALAAGRIKOMPLEKT
• Tootja: FEB

Üldine informatsioon: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Installatsiooni pool: Esisild
• Width [mm]: 40
• Inner Diameter [mm]: 40
• Outer Diameter [mm]: 74
• Bearing Type: Angular Ball Bearing
• Weight [kg]: 0.768
• Supplementary Article/Info 2: with retaining ring
• Supplementary Article/Supplementary Info: with axle nut
• Nimetus: SW 30 91 4250
• Tootja: SWAG

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Installatsiooni pool: Esisild
• Width [mm]: 40
• Inner Diameter [mm]: 40
• Outer Diameter [mm]: 74
• Nimetus: RATTALAAGRIKOMPLEKT
• Tootja: OPT

• Installatsiooni pool: Esisild
• Piirangutega toode/piirangu info: koos paigaldus-/kinnitusmaterjaliga
• Siseläbimõõt [mm]: 40
• Välisläbimõõt [mm]: 74
• Kõrgus (mm): 39,9
• Laagriteostus: Kuullaager
• Nimetus: RATTALAAGRIKOMPLEKT
• Tootja: MEY

Üldine informatsioon: With mounting materials, to fit most models. Please check fit accuracy before installation.

• Supplementary Article/Info 2: with wheel hub
• Fitting Position: Rear Axle, Rear Axle Left, Rear Axle Right
• Fabrication Number: KLT-VW-004
• Tootja: NTY
• Nimetus: NTY KLT-VW-004

• Fitting Position: Front Axle, Rear Axle
• Guarantee: 4 years guarantee
• Weight [kg]: 1.52
• Bolt Hole Circle Ø 1 [mm]: 100
• Always compare old and new part (in particular OE No.):
• Tootja: SKV GERMANY
• Nimetus: CE 29SKV439

• Installatsiooni pool: Esisild
• vajaminev tükihulk: 2
• Kaal (kg): 0,79
• pakendi pikkus [cm]: 11
• pakendi laius [cm]: 9
• pakendi kõrgus [cm]: 9
• Välisläbimõõt [mm]: 74
• Siseläbimõõt [mm]: 40
• Laius (mm): 40
• Tootja: CONTITECH-LOÅ»YSKA KÓŁ

• Installatsiooni pool: Esisild
• Piirangutega toode/piirangu info: Foto vastab tarnekomplektile
• Siseläbimõõt [mm]: 40
• Välisläbimõõt [mm]: 74
• Laius (mm): 40
• SVHC: SVHS aineid ei esine
• Nimetus: RATTALAAGRIKOMPLEKT
• Tootja: FAG

• Fitting Position: Rear Axle
• Outer Diameter [mm]: 120
• Tootja: KAMOKA PRZEGUBY PÓ£OSIE PIASTY

• Fitting Position: Front Axle both sides
• Rotation angle [°]: 60
• Diameter [mm]: 74
• Width [mm]: 40
• Weight [kg]: 0.71
• Inner Diameter [mm]: 40
• Outer Diameter [mm]: 74
• Tightening Torque [Nm]: 200, 60
• Weight [g]: 820
• Tootja: METALCAUCHO

• Fitting Position: Front
• General Information: wheel bearing with assembly parts; front
• Tootja: VIKA

• Installatsiooni pool: Esisild
• Outer Diameter [mm]: 74
• Inner Diameter [mm]: 40
• Width [mm]: 40
• Tootja: METZGER

• Installatsiooni pool: Tagasild
• Flange Diameter [mm]: 120
• Supplementary Article/Info 2: with ABS sensor ring
• Rim Hole Number: 5
• Tootja: DENCKERMANN ZAWIESZENIE

• Installatsiooni pool: Tagasild
• Tootja: DELLO AUTOMEGA

• Ehitusaasta alates: 07.2000
• Ehitusaasta kuni: 05.2002
• Fitting Position: Rear Axle
• Inner Diameter [mm]: 30
• Outer Diameter [mm]: 120
• Braking/Driving Dynamics: for vehicles with ABS
• Guarantee: 4 years guarantee
• Weight [kg]: 1.75
• Number of Holes: 5
• Bolt Hole Circle Ø 1 [mm]: 100
• Always compare old and new part (in particular OE No.):
• Tootja: SKV GERMANY
• Nimetus: CE 29SKV001

• Rotation angle [°]: 60
• Tightening Torque [Nm]: 60, 200
• Fitting Position: Front Axle Right, Front Axle Left
• Tootja: SNR
• Nimetus: SN R157.22

• Fitting Position: Front Axle
• Quantity per axle: 2
• Inner Diameter [mm]: 40
• Outer Diameter [mm]: 74
• Width [mm]: 40
• General Information: wheel bearing; front
• Tootja: VIKA

• vajaminev tükihulk: 2
• Supplementary Article/Info 2: with nut
• Outer Diameter [mm]: 74
• Inner Diameter [mm]: 40
• Fitting Position: Front Axle Left, Front Axle Right
• Tootja: AIC

General Information: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.

• Fitting Position: Rear Axle
• Width [mm]: 61.5
• Inner Diameter [mm]: 30
• Outer Diameter [mm]: 120
• Tootja: JPN

• Fitting Position: Front Axle both sides
• Weight [kg]: 0.662
• Inner Diameter [mm]: 40
• Outer Diameter [mm]: 74
• Supplementary Article/Info 2: without wheel hub
• Packaging length [cm]: 7.4
• Packaging width [cm]: 7.4
• Packaging height [cm]: 4
• Tootja: FEBEST

• Installatsiooni pool: Tagasild vasakul, Tagasild paremal
• Version: One
• Thread Size: M14X1,5
• Number of Teeth, ABS ring: 43
• Inner Diameter [mm]: 30
• Outer Diameter [mm]: 120
• Rim Hole Number: 5
• Supplementary Article/Info 2: with ABS sensor ring
• Inner Diameter 2 [mm]: 29
• Tootja: GSP

• Installatsiooni pool: Tagasild
• Laius (mm): 61,8
• Siseläbimõõt [mm]: 30
• Välisläbimõõt [mm]: 120
• Hammastehulk ABS-rõngas: 43
• Netokaal [kg]: 1,72
• Nimetus: RATTALAAGRIKOMPLEKT
• Tootja: NK

• Installatsiooni pool: Tagasild vasakul, Tagasild paremal
• Thread Size: M14X1,5
• Number of Teeth, ABS ring: 43
• Inner Diameter [mm]: 30
• Outer Diameter [mm]: 120
• Rim Hole Number: 5
• Supplementary Article/Info 2: with ABS sensor ring
• Inner Diameter 2 [mm]: 29
• Tootja: GSP

• Installatsiooni pool: Esisild
• vajaminev tükihulk: 2
• Width [mm]: 40
• Inner Diameter [mm]: 40
• Outer Diameter [mm]: 74
• Nimetus: RATTALAAGRIKOMPLEKT
• Tootja: SKF

• Installatsiooni pool: Tagasild
• Laius (mm): 63,5
• Hammastehulk ABS-rõngas: 43
• Siseläbimõõt [mm]: 30
• Välisläbimõõt 2 [mm]: 120
• Kinnitusaukude hulk: 5
• Tootja: METELLI LOZYSKA KOLA PIASTY

• Fitting Position: Front Axle
• Weight [kg]: 0.927
• Outer Diameter [mm]: 74
• Supplementary Article/Info 2: without wheel hub
• Packaging length [cm]: 8.5
• Packaging width [cm]: 7.4
• Packaging height [cm]: 7.4
• Tootja: FEBEST

• Fitting Position: Front
• General Information: Wheel bearing; front; without bolt
• Tootja: BORSEHUNG

• Installatsiooni pool: Tagasild mõlemapoolselt
• Hulk telje kohta: 2
• Veljeaukude hulk: 5
• Ava Ø (mm): 100
• Tootja: TOPRAN

Piirangutega toode/piirangu info 2: koos ABS-andurirõngaga, Rattalaager on integreeritud rattarummu Üldine informatsioon: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Installatsiooni pool: Tagasild
• Rim Hole Number: 5
• Flange Diameter [mm]: 120
• Supplementary Article/Info 2: with ABS sensor ring
• Kvaliteediklass: PJ
• Nimetus: Wheel hub

• Hulk: 2
• Fitting Position: Rear Axle
• Number of Holes: 5
• Weight [kg]: 2
• Required quantity: 2
• Bolt Hole Circle Ø [mm]: 100
• Width [mm]: 63
• Inner Diameter [mm]: 30
• Outer Diameter [mm]: 120
• Bearing Type: Rolling Bearing
• General Information: wheel hub with bearing; rear
• Tootja: VIKA

• Laius (mm): 63
• Siseläbimõõt [mm]: 30
• Välisläbimõõt [mm]: 120
• Ava Ø (mm): 100
• Aukude arv: 5
• Laagriteostus: Rulllaager
• Installatsiooni pool: Tagasild vasakul, Tagasild paremal
• Kaal (kg): 2
• Piirangutega toode/piirangu info: koos paigaldus-/kinnitusmaterjaliga
• Nimetus: RATTALAAGRIKOMPLEKT
• Tootja: FEB

Piirangutega toode/piirangu info 2: Rattalaager on integreeritud rattarummu, koos ABS-andurirõngaga Üldine informatsioon: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Installatsiooni pool: Tagasild vasakul, Tagasild paremal
• Sõiduki varustusvariant: REAR LR+RE LR+RE
• OE-numbri jaoks: 1J0598477
• Läbimõõt [mm]: 120
• Siseläbimõõt [mm]: 30
• Laius 1 (mm): 5
• Piirangutega toode/piirangu info 2: koos integreeritud ABS-anduriga
• Kinnitusaukude hulk: 1
• Nimetus: DA KWD1013
• Tootja: DAYCO

• Installatsiooni pool: Tagasild
• vajaminev tükihulk: 2
• Rim Hole Number: 5
• Supplementary Article/Info 2: with ABS sensor ring
• Tootja: DRIVE

• Laius (mm): 63
• Siseläbimõõt [mm]: 30
• Välisläbimõõt [mm]: 120
• Ava Ø (mm): 100
• Aukude arv: 5
• Laagriteostus: Rulllaager
• Installatsiooni pool: Tagasild vasakul, Tagasild paremal
• Kaal (kg): 1,506
• Nimetus: RATTALAAGRIKOMPLEKT
• Tootja: FEB

Piirangutega toode/piirangu info 2: Rattalaager on integreeritud rattarummu, koos ABS-andurirõngaga Üldine informatsioon: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Installatsiooni pool: Tagasild vasakul, Tagasild paremal
• Inner Diameter 1 [mm]: 30
• Outer Diameter 1 [mm]: 120
• Height 1 [mm]: 64
• Rim Hole Number: 5
• Weight [kg]: 2.68
• Number of Teeth, ABS ring: 43
• Thread Size: M14 x 1.5
• Bolt Hole Circle Ø [mm]: 100
• Tootja: ABS

Supplementary Article/Info 2: with integrated wheel bearing, with ABS sensor ring

• Installatsiooni pool: Tagasild
• Piirangutega toode/piirangu info: koos paigaldus-/kinnitusmaterjaliga
• Siseläbimõõt 1 [mm]: 30
• Välisläbimõõt [mm]: 120
• Ava Ø (mm): 100
• Hammastehulk ABS-rõngas: 43
• Veljeaukude hulk: 5
• Hammastehulk: 43
• Laagriteostus: Kuullaager
• Nimetus: RATTARUMM
• Tootja: MEY

Piirangutega toode/piirangu info 2: koos integreeritud rattalaagriga, koos ABS-andurirõngaga Üldine informatsioon: With mounting materials, to fit most models. Please check fit accuracy before installation.

• Fitting Position: Left
• General Information: Wheel bearing
• Tootja: BORSEHUNG

• OE-numbri jaoks: 1J0 501 477 A
• Installatsiooni pool: Tagasild mõlemapoolselt
• Piirangutega toode/piirangu info 2: koos ABS-andurirõngaga
• Tootja: TRUCKTEC

• Installatsiooni pool: Tagasild
• Width [mm]: 61.8
• Inner Diameter [mm]: 30
• Outer Diameter [mm]: 120
• Nimetus: RATTALAAGRIKOMPLEKT
• Tootja: OPT

• Laius (mm): 63
• Siseläbimõõt [mm]: 30
• Välisläbimõõt [mm]: 120
• Ava Ø (mm): 100
• Aukude arv: 5
• Laagriteostus: Rulllaager
• Installatsiooni pool: Tagasild vasakul, Tagasild paremal
• Kaal (kg): 1,506
• Nimetus: SW 99 90 9521
• Tootja: SWAG
• Lisainfo: 99 90 9521 SWA

Piirangutega toode/piirangu info 2: Rattalaager on integreeritud rattarummu, koos ABS-andurirõngaga Üldine informatsioon: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Installatsiooni pool: Esisild, esisild vasakul
• Piirangutega toode/piirangu info 2: koos pööreteanduriga
• Pistikkontaktide arv: 2
• Piduri-/sõidudünaamika: Sõidukitele koos ABS-ga
• Välisläbimõõt [mm]: 74
• vajaminev tükihulk: 1
• Laius (mm): 40
• Siseläbimõõt [mm]: 40
• Tootja: VEMO GERMANY

Üldine informatsioon: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Installatsiooni pool: Esisild, esisild paremal
• Välisläbimõõt [mm]: 74
• Pistikkontaktide arv: 2
• Piduri-/sõidudünaamika: Sõidukitele koos ABS-ga
• vajaminev tükihulk: 1
• Laius (mm): 40
• Piirangutega toode/piirangu info 2: koos pööreteanduriga
• Siseläbimõõt [mm]: 40
• Tootja: VEMO GERMANY

Üldine informatsioon: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Number of Holes: 5
• Supplementary Article/Info 2: with rubber mount
• Number of Teeth: 43
• Fitting Position: Rear Axle Right, Rear Axle Left
• Tootja: SNR
• Nimetus: SN R157.20

• Installatsiooni pool: Tagasild
• vajaminev tükihulk: 2
• Flange Diameter [mm]: 120
• Rim Hole Number: 5
• Supplementary Article/Info 2: with ABS sensor ring
• Nimetus: SK VKBA3456
• Tootja: SKF

• Fitting Position: Rear Axle
• Bolt Hole Circle Ø [mm]: 100
• Number of Holes: 5
• Weight [kg]: 1.506
• Supplementary Article/Info 2: Wheel Bearing integrated into wheel hub
• Required quantity: 2
• Width [mm]: 63
• Inner Diameter [mm]: 30
• Outer Diameter [mm]: 120
• Bearing Type: Rolling Bearing
• General Information: Wheel bearing assembly; rear
• Tootja: BORSEHUNG