• Kerenumber (VIN) alates: 70-1-065 260, 70-1X-058 732
• Fitting Position: frontal sided
• Outer Diameter [mm]: 47
• Inner Diameter [mm]: 32
• Width [mm]: 10
• Tootja: JP GROUP A/S
• Lisainfo: PAKENDIS 10 tk

• Fitting Position: transmission sided
• Inner Diameter [mm]: 85
• Outer Diameter [mm]: 105
• Thickness [mm]: 11
• Lisainfo: Oil seal for crankshaft, 85x105x11 mm

• Mootorikood: AET
• Mootori number kuni: 017277
• Fitting Position: transmission sided
• Inner Diameter [mm]: 85
• Outer Diameter [mm]: 105
• Width 1 [mm]: 9
• Width 2 [mm]: 11
• Housing Type: with housing
• Lisainfo: Seal flange for crankshaft

• Fitting Position: frontal sided
• General Information: Oil seal for crankshaft; front
• Tootja: VIKA

• Installatsiooni pool: stirnseitig
• Inner Diameter [mm]: 35
• Outer Diameter [mm]: 48
• Width [mm]: 10
• Material: FPM (fluoride rubber)
• Tootja: JP GROUP
• Lisainfo: Oil seal, 35x48x10 mm

• Installatsiooni pool: stirnseitig
• for manufacturer number: 8707043
• Tootja: KAMOKA

• Installatsiooni pool: stirnseitig
• for manufacturer number: 8707042
• Tootja: KAMOKA

• Installatsiooni pool: stirnseitig
• for manufacturer number: 8707050
• Tootja: KAMOKA

• Fitting Position: frontal sided
• Inner Diameter [mm]: 35
• Outer Diameter [mm]: 48
• Height [mm]: 10
• Swirl Type: Right-hand Twist
• Radial Shaft Seal Design: ASW
• Tootja: DR MOTOR PRZEWODY PRZELEWOWE
• Nimetus: DRM 01967

• Inner Diameter [mm]: 32
• Outer Diameter [mm]: 47
• Height [mm]: 10
• Dust Cover: with dust lip
• Swirl Type: Alternating Twist
• Fitting Position: frontal sided
• Material: FPM (fluoride rubber)
• Tootja: TOPRAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Inner Diameter [mm]: 35
• Outer Diameter [mm]: 48
• Height [mm]: 10
• Dust Cover: with dust lip
• Swirl Type: Right-hand Twist
• Fitting Position: frontal sided
• Material: FPM (fluoride rubber)/ACM (polyacrylate rubber)
• Tootja: TOPRAN HANS PRIES

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Fitting Position: frontal sided
• Inner Diameter [mm]: 32
• Outer Diameter [mm]: 47
• Thickness [mm]: 10
• General Information: Oil seal for camshaft; 47*10*32
• Tootja: VIKA

• Thickness [mm]: 10
• Inner Diameter [mm]: 35
• Outer Diameter [mm]: 48
• Material: ACM (Polyacrylate)
• Fitting Position: frontal sided
• Weight [kg]: 0.016
• Tootja: FEBI

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Mootorikood: AET
• Fitting Position: frontal sided
• Height [mm]: 10
• Outer Diameter [mm]: 48
• Inner Diameter [mm]: 35
• Material: ACM (Polyacrylate)
• Tootja: BGA

• Mootorikood: AET
• Mootori number kuni: 017 277
• Installatsiooni pool: stirnseitig
• Fitting Position: transmission sided
• Height [mm]: 11
• Material: FPM (fluoride rubber)
• Inner Diameter [mm]: 85
• Outer Diameter [mm]: 105
• Swirl Type: Left-hand Twist
• Dust Cover: with dust lip
• Tootja: DELLO AUTOMEGA

• Fitting Position: Front
• Inner Diameter [mm]: 35
• Outer Diameter [mm]: 48
• Height [mm]: 10
• Fabrication Number: NUP-VW-012
• Tootja: NTY

• Installatsiooni pool: stirnseitig
• for manufacturer number: 8707030
• Tootja: KAMOKA

• Installatsiooni pool: stirnseitig
• Inner Diameter [mm]: 35
• Outer Diameter [mm]: 48
• Width [mm]: 10
• Lisainfo: Oil seal, 35x48x10

Material: PTFE (polytetrafluoroethylene)/ACM (polyacrylate rubber)

• for OE number: 068 103 051 G
• Inner Diameter [mm]: 85
• Outer Diameter [mm]: 105
• Fitting Position: transmission sided
• Tootja: TRUCKTEC

• Installatsiooni pool: kastipoolselt
• for manufacturer number: 8707020
• Tootja: KAMOKA

• Installatsiooni pool: stirnseitig
• Inner Diameter [mm]: 35
• Outer Diameter [mm]: 48
• Height [mm]: 10
• Radial Shaft Seal Design: ASW
• Swirl Type: Right-hand Twist
• Material: FPM (fluoride rubber)
• Dust Cover: with dust lip
• Tootja: ELRING

• Fitting Position: Cylinder Head
• General Information: Oil seal for camshaft
• Tootja: VIKA

• Installatsiooni pool: stirnseitig
• Mootorikood: AET, APL, AVT
• Plokieraldus:
• Material: FPM (fluoride rubber)
• Inner Diameter [mm]: 35
• Outer Diameter [mm]: 48
• Height [mm]: 10
• Radial Shaft Seal Design: A SL
• Swirl Type: Right-hand Twist
• Tootja: REINZ USZCZELKI
• Nimetus: RN 81-24292-10

• Installatsiooni pool: stirnseitig
• Inner Diameter [mm]: 35
• Outer Diameter [mm]: 48
• Height [mm]: 10
• Radial Shaft Seal Design: ASW
• Swirl Type: Right-hand Twist
• Material: FPM (fluoride rubber)/ACM (polyacrylate rubber)
• Dust Cover: with dust lip
• Tootja: ELRING

• Installatsiooni pool: stirnseitig
• for manufacturer number: 8707007
• Tootja: KAMOKA

• Mootorikood: AET
• Mootori number kuni: 017277
• Fitting Position: transmission sided
• Inner Diameter [mm]: 85
• Outer Diameter [mm]: 105
• Width [mm]: 11
• Tootja: DR MOTOR PRZEWODY PRZELEWOWE
• Nimetus: DRM 0716

• Installatsiooni pool: kastipoolselt
• Mootorikood: AET
• Kogus pakendis: 10
• Fitting Position: frontal sided
• Tootja: VAICO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Mootorikood: AET
• Fitting Position: transmission sided
• Height [mm]: 12
• Outer Diameter [mm]: 105
• Inner Diameter [mm]: 85
• Material: NBR (nitrile butadiene rubber)
• Tootja: BGA USZCZELKI

• Mootori number kuni: 017277
• Inner Diameter [mm]: 85
• Outer Diameter [mm]: 105
• Height [mm]: 11
• Dust Cover: with dust lip
• Swirl Type: Left-hand Twist
• Material: FPM (fluoride rubber)
• Fitting Position: transmission sided
• Alternative Repair Kit: 105 753
• Tootja: TOPRAN HANS PRIES

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Thickness [mm]: 10
• Inner Diameter [mm]: 35
• Outer Diameter [mm]: 48
• Fitting Position: frontal sided
• Weight [kg]: 0.01
• Observe service information:
• Tootja: FEBI BILSTEIN

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Fitting Position: frontal sided
• General Information: Oil seal for crankshaft; front
• Tootja: BORSEHUNG

• Ehitusaasta alates: 11.1999
• Mootorikood: AVT
• Fitting Position: frontal sided
• Height [mm]: 10
• Outer Diameter [mm]: 48
• Inner Diameter [mm]: 35
• Tootja: BGA

Material: NBR (nitrile butadiene rubber), PTFE (polytetrafluoroethylene)

• Installatsiooni pool: kastipoolselt
• Mootori number kuni: AET 017 277
• Mootorikood: AET
• Material: FPM (fluoride rubber)
• Inner Diameter [mm]: 85
• Outer Diameter [mm]: 105
• Height [mm]: 11
• Radial Shaft Seal Design: A SL
• Swirl Type: Left-hand Twist
• Height 1 [mm]: 9
• Nimetus: RN 81-23708-40
• Tootja: REINZ
• Lisainfo: 81-23708-40

• Installatsiooni pool: kastipoolselt
• Mootorikood: AET
• Mootori number kuni: AET 017 277
• Inner Diameter [mm]: 85
• Outer Diameter [mm]: 105
• Height [mm]: 11
• Radial Shaft Seal Design: ASW
• Swirl Type: Left-hand Twist
• Material: FPM (fluoride rubber)
• Dust Cover: with dust lip
• Alternative Repair Kit: 829.056
• Tootja: ELRING

• Thickness [mm]: 11
• Inner Diameter [mm]: 85
• Outer Diameter [mm]: 105
• Material: FPM (fluoride rubber)
• Fitting Position: transmission sided
• Weight [kg]: 0.058
• Tootja: FEBI BILSTEIN

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Installatsiooni pool: stirnseitig
• Inner Diameter [mm]: 35
• Outer Diameter [mm]: 48
• Height [mm]: 10
• Radial Shaft Seal Design: ASW
• Swirl Type: Right-hand Twist
• Dust Cover: with dust lip
• Supplementary Article/Info 2: with mounting sleeve
• Observe mounting information:
• Tootja: ELRING

Material: PTFE (polytetrafluoroethylene)/ACM (polyacrylate rubber) Installation Information: Mounting dry and without any additional oil and grease

• Mootorikood: AVT
• Fitting Position: frontal sided
• Supplementary Article/Info 2: with mounting sleeve
• Height 1 [mm]: 10
• Outer Diameter 1 [mm]: 48
• Inner Diameter 1 [mm]: 35
• Material: PTFE (polytetrafluoroethylene)
• for OE number: 038103085
• Swirl Type: Right-hand Twist
• Dust Cover: with dust lip
• Nimetus: CO 20026412
• Tootja: CORTECO

• Mootorikood: AET
• Mootori number kuni: AET 017 277
• Kogus pakendis: 5
• Thickness [mm]: 11
• Inner Diameter [mm]: 85
• Outer Diameter [mm]: 105
• Fitting Position: transmission sided
• Tootja: VAICO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Installatsiooni pool: kastipoolselt
• Mootorikood: AET, APL
• Inner Diameter [mm]: 85
• Outer Diameter [mm]: 105
• Height [mm]: 12
• Tootja: AJUSA

• vajaminev tükihulk: 1
• Kogus pakendis: 5
• Fitting Position: transmission sided
• Tootja: AIC

General Information: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.

• Mootorikood: AET
• Mootori number kuni: 017277
• Installatsiooni pool: kastipoolselt
• Supplementary Article/Info 2: with flange
• Outer Diameter [mm]: 111
• Inner Diameter [mm]: 85
• Height [mm]: 16
• Tootja: DELLO AUTOMEGA

• Installatsiooni pool: stirnseitig
• Mootorikood: AVT
• Ehitusaasta alates: 11.1999
• Inner Diameter [mm]: 35
• Outer Diameter [mm]: 48
• Height [mm]: 10
• Swirl Type: Right-hand Twist
• Tootja: AJUSA

• Mootorikood: AET, APL, AVT
• Fitting Position: transmission sided
• Supplementary Article/Info 2: with mounting sleeve
• Height 1 [mm]: 11
• Outer Diameter 1 [mm]: 105
• Inner Diameter 1 [mm]: 85
• Material: FPM (fluoride rubber)
• for OE number: 068103071F
• Swirl Type: Alternating Twist
• Nimetus: CO 12015257
• Tootja: CORTECO

• Fitting Position: transmission sided
• Housing Type: with housing
• Housing material: Cast Aluminium
• Alternative Repair Kit: 101 407
• Sealing lip material: PTFE (polytetrafluoroethylene)
• Tootja: TOPRAN HANS PRIES

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Installatsiooni pool: kastipoolselt
• Ehitusaasta alates: 05.1999
• Mootorikood: APL
• Material: PTFE (polytetrafluoroethylene)
• for OE number: 038103171
• Tootja: FAI

• Installatsiooni pool: kastipoolselt
• Mootorikood: AET
• Mootori number kuni: AET 017 277
• Inner Diameter [mm]: 85
• Outer Diameter [mm]: 105
• Height [mm]: 11
• Radial Shaft Seal Design: ASW
• Swirl Type: Left-hand Twist
• Material: FPM (fluoride rubber)
• Dust Cover: with dust lip
• Supplementary Article/Info 2: with mounting sleeve
• Tootja: ELRING

• Fitting Position: transmission sided
• Weight [kg]: 0.17
• Inner Diameter [mm]: 85
• Required quantity: 1
• Supplementary Article/Info 2: with flange
• General Information: Oil sealing flange for crankshaft; rear
• Tootja: VIKA

• Mootorikood: APL, AVT
• Fitting Position: transmission sided
• Inner Diameter [mm]: 85
• Radial Shaft Seal Design: SP
• Housing Type: with housing
• Nimetus: DRM 01416
• Tootja: DR.MOTOR AUTOMOTIVE

• Installatsiooni pool: kastipoolselt
• for manufacturer number: 8707013
• Tootja: KAMOKA

• for OE number: 03G 105 021 C
• Thickness [mm]: 10
• Inner Diameter [mm]: 35
• Fitting Position: frontal sided
• Outer Diameter [mm]: 48
• Tootja: VAICO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Mootorikood: AVT, APL, AET
• Plokieraldus:
• Mootori number alates: 017 278
• Inner Diameter [mm]: 85
• Fitting Position: transmission sided
• Weight [kg]: 0.17
• Supplementary Article/Info 2: with flange
• Tootja: FEBI
• Lisainfo: FE37745

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Outer Diameter [mm]: 47
• Thickness [mm]: 10
• Inner Diameter [mm]: 32
• Fitting Position: transmission sided
• Tootja: VAICO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Fitting Position: transmission sided
• Weight [kg]: 0.17
• Inner Diameter [mm]: 85
• Required quantity: 1
• Supplementary Article/Info 2: with flange
• General Information: Oil sealing flange for crankshaft; rear
• Tootja: VIKA

• Installatsiooni pool: kastipoolselt
• Mootori number alates: AET 017 278
• Mootorikood: AET, APL, AVT
• Plokieraldus:
• Supplementary Article/Info 2: with flange
• Tootja: REINZ USZCZELKI

• Installatsiooni pool: kastipoolselt
• Mootorikood: APL, AVT, AET
• Plokieraldus:
• Mootori number alates: AET 017 278
• Inner Diameter [mm]: 85
• Radial Shaft Seal Design: SP
• Swirl Type: Left-hand Twist
• Housing Type: with housing
• Supplementary Article/Info 2: with mounting sleeve
• Observe mounting information:
• Tootja: ELRING

Material: PTFE (polytetrafluoroethylene)/ACM (polyacrylate rubber) Installation Information: Mounting dry and without any additional oil and grease