• Switch Pressure [bar]: 0.4
• Thread Size: M14x1.5
• Sensor Type: Closed-type Sensor
• Name: OLISURVELšLITUS
• Manufacturer: VER

• Engine Code: B202I
• Pressure [bar]: 0
• Thread Size: M14x1,5
• Spanner Size: 21
• Name: OLISURVELšLITUS
• Manufacturer: EPS

• Construction Year from: 01.1990
• Switch point from [bar]: 0.3
• Length [mm]: 44.8
• Switch point to [bar]: 0.55
• Inner Diameter [mm]: 2.5
• External Thread Size: M14 x 1,5
• Thread Length [mm]: 11.8
• Spanner Size: 24
• Number of connectors: 1
• Surface: Zinc-coated
• Weight [kg]: 0.04
• Supplementary Article/Info 2: with seal ring
• Name: SW 99 90 4726
• Manufacturer: SWAG

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Switch Pressure [bar]: 0.5
• Number of pins: 1
• Weight [kg]: 0.039
• Thread Size: M 14 x 1,5
• Pressure [bar]: 0.5
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Spanner Size: 19
• Colour: blue
• Number of pins: 2
• Thread Size: M12x1,5
• Length [mm]: 51
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: MAX
• Lisainfo: 21-0124
• Additional information: 21-0124

• Cable Length [mm]: 22
• Number of pins: 1
• Connecting thread: 1/8'' x 27 NPT
• Manufacturer: ERA

• Engine Code: B202I
• Thread Size: 1/8-27NPT
• Spanner Size: 13
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: EPS

• Thread Size: M12x1.5
• Spanner Size: 19
• Manufacturer: FAST

Manufacturer: FAE

• Sensor Type: NTC Sensor
• Mounting Type: Bolted
• Connector Shape: rectangular
• Number of pins: 2
• Spanner Size: 19
• Thread Size: M12x1.5
• for OE number: 195321101000
• Supplementary Article/Info 2: with seal ring
• Name: Andur,Jahutusvedeliku temp.
• Manufacturer: NRF

• Number of pins: 1
• Switch pressure from [bar]: 0.2
• Switch pressure to [bar]: 0.5
• Thread Size: M 14x1,5
• Housing Type: without housing
• Colour: black
• Supplementary Article/Supplementary Info: with gaskets/seals
• Quality: IAM
• Manufacturer: METZGER

• Construction Year from: 02.1989
• Thread Size: 1/8x27 NPTF
• Manufacturer: VERNET

• Thread Size: M12 x 1,5
• Spanner Size: 19
• Number of pins: 2
• Connector Shape: rectangular
• Manufacturer: ERA

• Thread Size: M12x1.5
• Manufacturer: VERNET

• Engine Code: B202I
• Sensor Type: NTC Sensor
• Thread Size: 1/8"X27 NPTF
• Number of pins: 1
• Thread Type: with tapered thread
• Manufacturer: MEYLE

• Engine Code: B202I
• Colour: blue
• Thread Size: M12x1,5
• Spanner Size: 19
• for article number: 1.880.113, 1.880.114, 1.880.149, 1.880.151
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: EPS

• Length [mm]: 50.7
• External Thread Size: M12 x 1,5
• Thread Length [mm]: 11
• Spanner Size: 19
• Number of connectors: 2
• Colour: blue
• Colour Coding: blue
• Switch Point [°C]: 20
• Weight [kg]: 0.022
• Supplementary Article/Info 2: with seal ring
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: FEB

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Housing Colour: blue
• Number of pins: 2
• Thread Size: M12X1.5-6g
• Spanner Size: 19
• Manufacturer: DELPHI

• Length [mm]: 50.7
• External Thread Size: M12 x 1,5
• Thread Length [mm]: 11
• Spanner Size: 19
• Number of connectors: 2
• Colour: blue
• Colour Coding: blue
• Switch Point [°C]: 20
• Weight [kg]: 0.022
• Supplementary Article/Info 2: with seal ring
• Manufacturer: SWAG
• Name: SW 40 91 7695
• Lisainfo: 40 91 7695 SWA
• Additional information: 40 91 7695 SWA

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Engine Code: B202I
• Mounting Type: Bolted
• Voltage [V]: 12
• Resistor [Ohm]: 2,080, 302
• Supplementary Article/Supplementary Info: with seal
• Temperature range from [°C]: 25
• Temperature range to [°C]: 80
• Thread Size: M12x1,5
• Colour: blue
• Spanner Size: 19
• Sensor Type: NTC Sensor
• Number of pins: 2
• Corresponds to the original part in colour: blue
• Manufacturer Restriction: Bosch
• Assy./disassy. by qualified personnel required!:
• Manufacturer: HELLA

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Engine Code: B202I
• Sensor Type: NTC Sensor
• Thread Size: M12 x 1,5
• Spanner Size: 19
• Colour: blue
• Number of pins: 2
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: MEY

• Thread Size: M12x1.5
• Number of pins: 2
• Manufacturer: ERA

• Number of pins: 2
• Weight [kg]: 0.05
• Manufacturer: ERA

• Number of circuits: 3
• Lambda Sensor: Regulating Probe
• Manufacturer: KAMOKA

• Supplementary Article/Info 2: without cable
• Number of pins: 2
• Housing Colour: black
• Manufacturer: FAE

• Lambda Sensor: Lambda Sensor
• Voltage [V]: 12
• Number of circuits: 3
• Weight [kg]: 0.08
• Operating Mode: Electric
• Warranty: 3 years warranty
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY
• Name: CE 09SKV903

• Lambda Sensor: Regulating Probe, Heated
• Manufacturer Restriction: Bosch
• Fitting Position: before catalytic converter
• Engine Code: B202I
• Number of circuits: 3
• Overall Length [mm]: 1,270
• Name: LAMBDA ANDUR
• Manufacturer: MAX

• Length [mm]: 1,215
• Number of circuits: 3
• Resistor [Ohm]: 4.5
• Conductor Number: 3
• Cable Length [mm]: 1,215
• Lambda Sensor: Heated
• Manufacturer: MAGNETI MARELLI
• Name: MM OSM078

• Number of circuits: 3
• Overall Length [mm]: 1,236
• Lambda Sensor: Heated
• Lisainfo: Lambda sensor
• Additional information: Lambda sensor

• Lambda Sensor: Regulating Probe
• Voltage [V]: 12
• Length [mm]: 1,215
• Number of circuits: 3
• Weight [kg]: 0.13
• Operating Mode: Electric
• Warranty: 3 years warranty
• Always compare old and new part (in particular OE No.):
• Name: CE 09SKV066
• Manufacturer: ESEN SKV

• Lambda Sensor: Regulating Probe
• Voltage [V]: 12
• Length [mm]: 1,670
• Number of circuits: 3
• Weight [kg]: 0.23
• Resistor [Ohm]: 4.5
• Operating Mode: Electric
• Warranty: 3 years warranty
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY
• Name: CE 09SKV546

• Lambda Sensor: Regulating Probe, Finger probe, Heated
• Engine Code: B202I
• Manufacturer Restriction: Bosch
• Cable Length [mm]: 1
• Manufacturer: DELPHI

• for OE number: 75 01 612
• Weight [kg]: 0.025
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.