• for OE number: 82 00 719 629
• Number of pins: 3
• Pressure from [kPA]: 20
• Pressure to [kPA]: 100
• Fabrication Number: ECM-RE-003
• Manufacturer: NTY
• Name: NTY ECM-RE-003

• Manufacturer: VERNET
• Additional information: AS0006 VERNET
• Lisainfo: AS0006 VERNET

• Construction Year to: 12.2012
• Voltage [V]: 12
• Supplementary Article/Supplementary Info: without cable pull
• Number of pins: 3
• Guarantee: 3 years guarantee
• Weight [kg]: 0.02
• Operating Mode: Electric
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY
• Name: CE 17SKV114

• Length [mm]: 445
• Fitting Position: Front, before catalytic converter
• Oxygen Sensor: Regulating Sensor, Thread pre-greased
• Fabrication Number: ESL-RE-000
• Manufacturer: NTY
• Name: NTY ESL-RE-000

Manufacturer: MAGNETI MARELLI

• Measuring Range from [kPa]: 20
• Measuring Range to [kPa]: 100
• Measuring Range from [V]: 0.52
• Measuring Range to [V]: 4.75
• Number of connectors: 3
• Manufacturer: VERNET
• Additional information: MS0119 VERNET
• Lisainfo: MS0119 VERNET

• Number of pins: 3
• Pressure from [kPA]: 20
• Pressure to [kPA]: 100
• Quality: OE EQUIVALENT
• for OE number: 8200719629
• Manufacturer: MEAT&DORIA

• Oxygen Sensor: Diagnostic Probe, Thread pre-greased
• Fabrication Number: ESL-SK-000
• Manufacturer: NTY
• Name: NTY ESL-SK-000

• Required quantity: 1
• Name: CZUJNIK CI—N. POWIETRZA RENAULT CLIO 2,0 16V 00-
• Manufacturer: BRM

• Construction Year to: 12.2012
• Thread Size: M12 x 1,5
• Spanner Size: 21
• Number of pins: 3
• Colour Coding: black
• Manufacturer: VIEROL

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Engine Code: K4M 743
• Number of pins: 2
• Connector Shape: rectangular
• Thread Size: M12x1,25
• Spanner Size: 24
• for OE number: 2206000Q0A
• Manufacturer: MEAT&DORIA

• Alternatively:
• Number of pins: 3
• Pressure from [kPA]: 20
• Pressure to [kPA]: 100
• Weight [kg]: 0.014
• Alternative Repair Kit: 550086
• Manufacturer: ERA

• Thread Size: M12x1.25
• Spanner Size: 24
• Number of pins: 2
• Connector Shape: rectangular
• Manufacturer: FAST

• Number of pins: 3
• Pressure from [kPA]: 20
• Pressure to [kPA]: 100
• for OE number: 71739292
• Manufacturer: MEAT&DORIA

• Oxygen Sensor: Regulating Sensor
• Number of circuits: 4
• Manufacturer: KAMOKA

• Construction Year to: 12.2012
• Block Separation:
• Oxygen Sensor: Diagnostic Probe, Heated
• Length [mm]: 470
• Number of circuits: 4
• Name: Lambda andur
• Manufacturer: MAX

Fitting Position: Front, after catalytic converter, before catalytic converter

• Number of pins: 2
• Name: DETONATSIOONIANDUR
• Manufacturer: DLP

• Engine Code: K4M674
• Block Separation:
• Cable Length [mm]: 460
• Manufacturer: DELPHI
• Name: DE ES20656-12B1

Oxygen Sensor: Diagnostic Probe, Regulating Sensor, Planar Sensor, Heated Fitting Position: after catalytic converter, before catalytic converter

• Transmission Type: Manual Transmission
• Oxygen Sensor: Diagnostic Probe
• Length [mm]: 470
• Number of connectors: 4
• Manufacturer: VERNET

• Construction Year from: 10.2008
• Construction Year to: 06.2014
• Oxygen Sensor: Regulating Sensor, Finger-type Sensor
• Fitting Position: before catalytic converter
• Number of circuits: 4
• Connector/Clamp: Connector may need adjustment
• Transmission Type: Manual Transmission
• Name: LAMBDA ANDUR
• Manufacturer: MAX

• Construction Year from: 10.2008
• Construction Year to: 06.2014
• Oxygen Sensor: Regulating Sensor, Diagnostic Probe, Heated
• Block Separation:
• Number of circuits: 4
• Connector/Clamp: Connector may need adjustment
• Name: LAMBDA ANDUR
• Manufacturer: MAX
• Lisainfo: MGS-615
• Additional information: MGS-615

Fitting Position: before catalytic converter, after catalytic converter

• Supplementary Article/Info 2: without cable
• Supplementary Article/Supplementary Info: with gasket/seal
• Number of pins: 3
• Assy./disassy. by qualified personnel required!:
• SVHC: 7439-92-1; Lead
• Manufacturer: HELLA
• Name: HE 6PP009400281

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Oxygen Sensor: Regulating Sensor
• Fitting Position: before catalytic converter
• Construction Year from: 10.2008
• Construction Year to: 06.2014
• Length [mm]: 560
• Technical Information Number: Universal 77015
• Manufacturer: FAE

Manufacturer: MAGNETI MARELLI

• Oxygen Sensor: Heated
• Number of pins: 4
• Cable Length [mm]: 330
• Quality: OE EQUIVALENT
• for OE number: 00001628SW
• Manufacturer: MEAT&DORIA

• Construction Year to: 12.2012
• Oxygen Sensor: Regulating Sensor, Heated
• Fitting Position: before catalytic converter
• Engine Code: K4M670
• Vehicle type: Thalia
• Cable Length [mm]: 395
• Number of pins: 4
• Assy./disassy. by qualified personnel required!:
• Name: Lambda andur
• Manufacturer: HEL

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Engine Code: K4M670
• Block Separation:
• Cable Length [mm]: 470
• Name: LAMBDA ANDUR
• Manufacturer: DLP

Oxygen Sensor: Diagnostic Probe, Regulating Sensor, Planar Sensor, Heated Fitting Position: after catalytic converter, before catalytic converter Additional information: "Tootja: DELPHI
TWINGO (C06/), 03.93
(kvaliteediklass: PJ)" Lisainfo: "Tootja: DELPHI
TWINGO (C06/), 03.93
(kvaliteediklass: PJ)"

• Block Separation:
• Cable Length [mm]: 450
• Name: LAMBDA ANDUR
• Manufacturer: DLP
• Quality class: PJ

Oxygen Sensor: Regulating Sensor, Diagnostic Probe, Planar Sensor, Heated Fitting Position: before catalytic converter, after catalytic converter Additional information: "Tootja: DELPHI
MEGANE II (BM0/1/, C
(kvaliteediklass: PJ)" Lisainfo: "Tootja: DELPHI
MEGANE II (BM0/1/, C
(kvaliteediklass: PJ)"

• Engine Code: K4M 743
• Oxygen Sensor: Regulating Sensor
• Ülekandeliinide arv: 4
• Piirangutega toode/piirangu info 2: ilma pistikuta
• Name: LAMBDA ANDUR
• Manufacturer: NTK

• Length [mm]: 470
• Resistor [Ohm]: 9
• Number of circuits: 4
• Conductor Number: 4
• Cable Length [mm]: 470
• Oxygen Sensor: Heated
• Name: LAMBDA ANDUR
• Manufacturer: MAG

• Construction Year from: 10.2008
• Construction Year to: 06.2014
• Oxygen Sensor: Diagnostic Probe
• Fitting Position: after catalytic converter
• Number of circuits: 4
• Overall Length [mm]: 408
• Available as universal article as well, see article no.: 0258986615
• Recommended change interval [km]: 160,000
• Name: LAMBDA ANDUR
• Manufacturer: BOS

• Oxygen Sensor: Regulating Sensor
• Guarantee: 5 years guarantee
• Overall Length [mm]: 580
• Number of circuits: 4
• General Information: Sold in Hueco brand: printing and packaging
• Name: HU 135326
• Manufacturer: HITACHI

• Construction Year from: 10.2008
• Construction Year to: 06.2014
• Oxygen Sensor: Regulating Sensor, Diagnostic Probe
• Block Separation:
• Number of circuits: 4
• Recommended change interval [km]: 160,000
• Connector/Clamp: Connector may need adjustment
• Name: LAMBDA ANDUR
• Manufacturer: BOS

Fitting Position: before catalytic converter, after catalytic converter

• Oxygen Sensor: Regulating Sensor, Planar Sensor, Heated
• Fitting Position: before catalytic converter
• Cable Length [mm]: 440
• Manufacturer: DELPHI
• Name: DE ES10793-12B1

• Construction Year from: 10.2008
• Construction Year to: 12.2013
• Engine Code: K4M.6.70,K4M.6.74, K4M.6.77,K4M.7.44, K4M.7.45
• Name: DETONATSIOONIANDUR
• Manufacturer: VAL

• Exhaust System: for pre-catalytic converter
• Thread Size: M18x1.5
• Cable Length [mm]: 750
• Number of pins: 4
• Manufacturer Restriction: DENSO
• Quality: OE
• Weight [g]: 93
• Gross Weight [g]: 140
• Manufacturer: DENSO
• Name: DN DOX-0150
• Quality class: Q

Oxygen Sensor: Regulating Sensor, Heated, Planar Sensor, Thread pre-greased, Switching-type Oxygen Sensor Additional information: "Tootja: DENSO
(kvaliteediklass: Q)" Lisainfo: "Tootja: DENSO
(kvaliteediklass: Q)"

• Construction Year from: 10.2008
• Construction Year to: 12.2013
• Engine Code: K4M.6.70
• Fitting Position: before catalytic converter
• Oxygen Sensor: Planar Sensor, Thread pre-greased, Heated
• Number of pins: 4
• Cable Length [mm]: 300
• Thread Size: M18x1,5
• Switch Pressure [bar]: 4
• Connector Shape: oval
• Weight [kg]: 0.13
• Name: VA 368065
• Manufacturer: VALEO

• Construction Year from: 10.2008
• Construction Year to: 06.2014
• Oxygen Sensor: Regulating Sensor
• Fitting Position: before catalytic converter
• Number of circuits: 4
• Overall Length [mm]: 480
• Available as universal article as well, see article no.: 0258986615
• Recommended change interval [km]: 160,000
• Name: LAMBDA ANDUR
• Manufacturer: BOS

• Construction Year from: 10.2008
• Construction Year to: 12.2013
• Engine Code: K4M.6.77,K4M.7.44, K4M.7.45
• Oxygen Sensor: Planar Sensor, Thread pre-greased, Heated
• Number of pins: 4
• Cable Length [mm]: 400
• Thread Size: M18x1,5
• Switch Pressure [bar]: 4
• Connector Shape: oval
• Weight [kg]: 0.13
• Name: VA 368040
• Manufacturer: VALEO

Fitting Position: before catalytic converter, after catalytic converter

• Lambda andur: Bistabiilne andur
• Kaablipikkus (mm): 290
• valikuliselt:
• Ülekandeliinide arv: 4
• alternatiivne remondikomplekt: 570112
• Manufacturer: ERA

• Exhaust System: for pre-catalytic converter
• Thread Size: M18x1.5
• Cable Length [mm]: 470
• Number of pins: 4
• Manufacturer Restriction: DENSO
• for OE number: 7700107433
• Quality: OE
• Weight [g]: 118
• Gross Weight [g]: 151
• Manufacturer: DENSO
• Name: Lambda sensor
• Quality class: Q

Oxygen Sensor: Regulating Sensor, Heated, Planar Sensor, Thread pre-greased, Switching-type Oxygen Sensor Additional information: "Tootja: DENSO
TWINGO (C06/), 03.93
(kvaliteediklass: Q)" Lisainfo: "Tootja: DENSO
TWINGO (C06/), 03.93
(kvaliteediklass: Q)"

• Engine Code: K4M674
• Number of pins: 4
• Cable Length [mm]: 450
• Thread Size: M18x1,5
• Switch Pressure [bar]: 4
• Connector Shape: oval
• Weight [kg]: 0.134
• Manufacturer: VALEO
• Name: VA 368236

Oxygen Sensor: Regulating Sensor, Diagnostic Probe, Planar Sensor, Thread pre-greased, Heated Fitting Position: before catalytic converter, after catalytic converter

• Construction Year to: 03.2013
• Oxygen Sensor: Regulating Sensor, Switching-type Oxygen Sensor
• Fitting Position: before catalytic converter
• Required quantity: 1
• Vehicle type: Symbol
• Cable Length [mm]: 560
• Number of pins: 4
• Assy./disassy. by qualified personnel required!:
• Name: HE 6PA009166971
• Manufacturer: HELLA

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Oxygen Sensor: Diagnostic Probe, Finger-type Sensor, Heated
• Fitting Position: after catalytic converter
• Engine Code: K4M670
• Cable Length [mm]: 317
• Manufacturer: DELPHI

• Construction Year to: 03.2013
• Fuel Type: Petrol
• Number of pins: 3
• Manufacturer: VIEROL

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.