• for OE number: 9109810
• Spanner Size: 21
• Housing Colour: black
• Manufacturer: KAMOKA

• Engine Code: J7R 756
• Thread Size: M12x1,5
• Spanner Size: 19
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: MAX

• Switch Pressure [bar]: 0.3
• Thread Size: M18x1.5
• Sensor Type: Closed-type Sensor
• Name: OLISURVELšLITUS
• Manufacturer: VER

• Engine Code: J7R 756
• Pressure [bar]: 0.5
• Thread Size: M18x1,5
• Spanner Size: 21
• Name: OLISURVELšLITUS
• Manufacturer: EPS

• Thread Size: M14 x 1,5
• Pressure to [bar]: 0.42
• Pressure from [bar]: 0.28
• Number of pins: 1
• Manufacturer: AIC

General Information: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.

• Vehicle Identification Number (VIN) to: F00349091
• Thread Size: M 14x1,5
• Housing Colour: grey
• Manufacturer: FAE

• Thread Size: M12x1.5
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: VER

• Sensor Type: NTC Sensor
• Mounting Type: Bolted
• Connector Shape: round
• Number of pins: 1
• Socket colour: brown
• Spanner Size: 19
• Thread Size: M14x1.25
• for OE number: T0771821
• Manufacturer: NRF

• for OE number: 9118368
• Sensor Type: Passive sensor
• Manufacturer: KAMOKA

• Thread Size: M14x1.5
• Manufacturer: VERNET

• Sensor Type: NTC Sensor
• Mounting Type: Bolted
• Connector Shape: rectangular
• Number of pins: 2
• Socket colour: black
• Spanner Size: 21
• Thread Size: M12x1.5
• for OE number: 9109810
• Supplementary Article/Info 2: with seal ring
• Name: Andur,Jahutusvedeliku temp.
• Manufacturer: NRF

• Fabrication Number: ECT-CH-011
• Number of pins: 2
• Voltage [V]: 12
• Housing Colour: white
• Sensor Type: NTC Sensor
• Manufacturer: NTY
• Name: NTY ECT-CH-011

• Cable Length [mm]: 520
• Number of pins: 2
• Sensor Type: Inductive Sensor
• Assy./disassy. by qualified personnel required!:
• Manufacturer: ABAKUS

General Information: The following information is for general and informational purposes only and does not constitute warranty terms. Warranty terms and conditions are available from our dealers and in our general terms and conditions of sale. Abakus spare/repair parts are intended only for vehicle repairs in order to restore their original functionality. Abakus spare/repair parts are used or sold to users only for the purpose of repairing vehicles to restore their original look and functionality and are not original/genuine/OE/OEM/OES replacement parts. These items do not originate from the vehicle manufacturer and may be the subject of a design not owned by Abakus and the manufacturer of this spare part. They may only be used for repairs to restore the intended vehicle to its original appearance. Our products are delivered without instruction of installation. Installation of our product may only be carried out by trained specialist technicians in specific car repairs. Products supplied by us are exclusively intended for proper and appropriate use. The warranty may become invalid in the event of: improper installation or repair, unsuitable application or use, installation or repair made outside specialist car workshops. Warranty claims are lost if the vehicle is modified and used for motor sports, tuning or similar events (except our tuning parts which are described in TecDoc and on our price list). Warranty application should include complete documentation among others: chassis no., first registration, vehicle mileage, information about LPG installation, fault memory log, pictures, our QC (quality check) code, installation invoice, contact details of the car repair workshop performing the replacement or repair. Warranty application are available in our Client Panel system. Complaints may require supplementing data such as error memory logs. Incomplete documentation may result in rejection of the claim. Any damage caused during transport is not considered quality damage and will be considered on an individual basis. The product is intended for use within the performance limits specified by the manufacturer and should only be used by qualified personnel who have been trained to operate this product. Before each use, the product should be checked for damage or fixing of its parts and not used if any defects or loose parts are found. Failure to follow the manufacturer's guidelines could result in potential product damage or even injury. Wear appropriate protective clothing if necessary when working with the product.

• Engine Code: J7R 756
• Thread Size: M12x1,5
• Spanner Size: 19
• Manufacturer: FACET
• Name: EP 1.830.191

• Engine Code: J7R 756
• Thread Size: M12x1,5
• Spanner Size: 19
• Manufacturer: FACET

• Voltage [V]: 12
• Thread Size: M 14x1,5
• Number of pins: 2
• Housing Colour: white
• Manufacturer: FAE ELEKTRYKA

• Number of pins: 2
• Weight [kg]: 0.3
• Packaging length [cm]: 12
• Packaging width [cm]: 8
• Packaging height [cm]: 6

• Cable Length [mm]: 445
• Number of pins: 2
• Manufacturer: DELPHI
• Name: DE SS10757-12B1

• Engine Code: J7R.7.56
• Sensor Type: Inductive Sensor
• Number of pins: 2
• Voltage [V]: 12
• Connector Shape: oval
• Supplementary Article/Info 2: with cable
• Resistor [Ohm]: 240
• Weight [kg]: 0.1
• Manufacturer: VALEO
• Name: VA 254103

• Engine Code: J7R 756
• Switch Point [°C]: 125
• Thread Size: M14x1.25
• Manufacturer: VERNET

• Engine Code: J7R 756
• Thread Size: M14x1,5
• Spanner Size: 21
• Name: ANDUR,SISENDOHU TEMPERATUUR
• Manufacturer: EPS

• Engine Code: J7R 756
• Warn Temperature [°C]: 125
• Thread Size: M14x1,25
• Spanner Size: 22
• Name: EP 1.830.510
• Manufacturer: EPS

• Engine Code: J7R.7.56
• Colour: white
• Cable Length [mm]: 520
• Required quantity: 1
• Number of pins: 2
• Resistor [Ohm]: 240
• Sensor Type: Inductive Sensor
• Number of connectors: 2
• Rated Voltage [V]: 12
• Fitting Depth [mm]: 24
• Manufacturer: VIEROL

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Number of pins: 2
• Manufacturer: JPN

• Engine Code: J7R 756
• Thread Size: M12x1,25
• Spanner Size: 24
• Name: DETONATSIOONIANDUR
• Manufacturer: EPS

• Thread Size: M12x1.25
• Spanner Size: 24
• Number of pins: 2
• Connector Shape: rectangular
• Manufacturer: FAST

• Engine Code: J7R 756
• Length [mm]: 540
• Name: ANDUR, VŽNTVOLL
• Manufacturer: EPS

• Oxygen Sensor: Regulating Sensor, Switching-type Oxygen Sensor
• Voltage [V]: 12
• Number of circuits: 3
• Weight [kg]: 0.08
• Operating Mode: Electric
• Always compare old and new part (in particular OE No.):
• Manufacturer: ENERGY

• Engine Code: J7R 756
• Cable Length [mm]: 520
• Manufacturer: FAE

• Oxygen Sensor: Regulating Sensor
• Number of circuits: 3
• Manufacturer: KAMOKA

• Oxygen Sensor: Regulating Sensor, Switching-type Oxygen Sensor
• Voltage [V]: 12
• Guarantee: 3 years guarantee
• Number of circuits: 3
• Weight [kg]: 0.08
• Operating Mode: Electric
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY
• Name: CE 09SKV903

• Technical Information Number: Universal
• Overall Length [mm]: 315
• Number of pins: 3
• Oxygen Sensor: Regulating Sensor
• Manufacturer: ASHIKA

• Oxygen Sensor: Regulating Sensor, Switching-type Oxygen Sensor
• Exhaust System: for pre-catalytic converter
• Voltage [V]: 12
• Guarantee: 3 years guarantee
• Number of circuits: 4
• Weight [kg]: 0.09
• Resistor [Ohm]: 13
• Operating Mode: Electric
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY
• Name: CE 09SKV913

• Resistor [Ohm]: 4.5
• Conductor Number: 3
• Length [mm]: 375
• Number of circuits: 3
• Cable Length [mm]: 375
• Oxygen Sensor: Heated
• Name: LAMBDA ANDUR
• Manufacturer: MAG

• Oxygen Sensor: Regulating Sensor, Switching-type Oxygen Sensor
• Voltage [V]: 12
• Length [mm]: 422
• Guarantee: 3 years guarantee
• Number of circuits: 3
• Weight [kg]: 0.09
• Operating Mode: Electric
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY

• Exhaust System: for pre-catalytic converter
• Thread Size: M18x1.5
• Cable Length [mm]: 750
• Number of pins: 3
• Manufacturer Restriction: DENSO
• Quality: OE
• Weight [g]: 95
• Gross Weight [g]: 144
• Manufacturer: DENSO
• Lisainfo: DOX-0116 DENSO
• Additional information: DOX-0116 DENSO

Oxygen Sensor: Regulating Sensor, Heated, Finger-type Sensor, Switching-type Oxygen Sensor

Manufacturer: MAGNETI MARELLI

• Oxygen Sensor: Switching-type Oxygen Sensor
• Voltage [V]: 12
• Length [mm]: 570
• Guarantee: 3 years guarantee
• Number of circuits: 3
• Weight [kg]: 0.15
• Resistor [Ohm]: 4.5
• Operating Mode: Electric
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY

• Oxygen Sensor: Regulating Sensor, Finger-type Sensor, Heated
• Engine Code: J7R 756
• Cable Length [mm]: 400
• Name: LAMBDA ANDUR
• Manufacturer: DLP

• Engine Code: J7R 756
• Oxygen Sensor: Regulating Sensor
• Fitting Position: before catalytic converter
• Length [mm]: 450
• Technical Information Number: Universal 77003
• Manufacturer: FAE

• Engine Code: J7R.7.56
• Name: DETONATSIOONIANDUR
• Manufacturer: VAL

• Oxygen Sensor: Regulating Sensor
• Fitting Position: before catalytic converter
• for OE number: 7700854148
• Number of circuits: 3
• Recommended change interval [km]: 160,000
• Connector/Clamp: Connector may need adjustment
• Name: LAMBDA ANDUR
• Manufacturer: BOS

• Number of pins: 2
• Connector Shape: oval
• Socket colour: grey
• Cable Length [mm]: 500
• Sensor Type: Inductive Sensor
• for OE number: 7700739794
• Lisainfo: 87030 NIS
• Additional information: 87030 NIS

• Exhaust System: for pre-catalytic converter
• Thread Size: M18x1.5
• Cable Length [mm]: 375
• Number of pins: 3
• Manufacturer Restriction: DENSO
• for OE number: 7700746375
• Quality: OE
• Weight [g]: 91
• Gross Weight [g]: 121
• Manufacturer: DENSO

Oxygen Sensor: Regulating Sensor, Heated, Finger-type Sensor, Switching-type Oxygen Sensor

• Catalytic Converter Type: for vehicles with catalytic converter
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Oxygen Sensor: Regulating Sensor
• Fitting Position: before catalytic converter
• for OE number: 7700854148
• Number of circuits: 3
• Overall Length [mm]: 560
• Available as universal article as well, see article no.: 0258986502
• Recommended change interval [km]: 160,000
• Name: LAMBDA ANDUR
• Manufacturer: BOS

• for OE number: 08 26 285
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.