• Colour Coding: grey
• Number of pins: 2
• Manufacturer: JP GROUP
• Lisainfo: Sender for water temperature gauge, 2 pins
• Additional information: Sender for water temperature gauge, 2 pins

• Construction Year from: 01.2008
• Rated Voltage [V]: 12
• Pressure from [bar]: 0.35
• Pressure to [bar]: 0.55
• Number of pins: 1
• Lisainfo: PAKENDIS 10 tk
• Additional information: PAKENDIS 10 tk

• Switch Pressure [bar]: 0.4
• Thread Size: M14x1.5
• Sensor Type: Closed-type Sensor
• Manufacturer: VERNET

• Engine Code: M 97.22
• Pressure [bar]: 0.3
• Thread Size: M14x1,5
• Spanner Size: 24
• Name: EP 1.800.023
• Manufacturer: EPS

• Engine Code: M 97.22
• Pressure [bar]: 0.3
• Thread Size: M14x1,5
• Spanner Size: 24
• Manufacturer: FACET

• Pressure [bar]: 5.5
• Housing Colour: brown
• Thread Size: M14x1.5
• Diameter [mm]: 24
• Spanner Size: 24
• Number of pins: 1
• Manufacturer: DELPHI
• Name: DE SW90003

• Construction Year from: 01.2008
• Thread Size: M14x1,5
• Control Range [bar]: 0,3 - 0,55
• Manufacturer: VEMO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Sensor Type: NTC Sensor
• Mounting Type: Clamped
• Connector Shape: D Shape
• Number of pins: 2
• for OE number: 06A919501
• Supplementary Article/Info 2: with mounting parts
• Manufacturer: NRF

• Construction Year from: 01.2008
• Voltage [V]: 12
• Combi Switch Function: Normally Closed Contact
• Current Strength [A]: 0.25
• Thread Size: M14x1,5
• Spanner Size: 24
• Pressure from [bar]: 0.35
• Pressure to [bar]: 0.55
• Number of pins: 1
• Corresponds to the original part in colour: black
• Assy./disassy. by qualified personnel required!:
• Manufacturer: HELLA

• Engine Code: M 97.22
• for article number: 1.660.015K, 1.830.278K, 1.879.946
• Name: EP 1.830.278
• Manufacturer: EPS
• Additional information: 1-830-278
• Lisainfo: 1-830-278

• Engine Code: M 97.22
• for article number: 26.0015K, 7.3278K, 7.7946
• Manufacturer: FACET

• Thread Size: M20
• Number of pins: 2
• Housing Colour: grey
• Connector Shape: oval
• Manufacturer: ERA

• Construction Year to: 08.2008
• Manufacturer: BOSCH

• Fabrication Number: ESS-FT-002
• Manufacturer: NTY

• Number of pins: 2
• Housing Colour: grey
• Manufacturer: FAE

• Supplementary Article/Info 2: without cable
• Number of pins: 3
• Sensor Type: Hall Sensor
• Assy./disassy. by qualified personnel required!:
• Manufacturer: ABAKUS

General Information: The following information is for general and informational purposes only and does not constitute warranty terms. Warranty terms and conditions are available from our dealers and in our general terms and conditions of sale. Abakus spare/repair parts are intended only for vehicle repairs in order to restore their original functionality. Abakus spare/repair parts are used or sold to users only for the purpose of repairing vehicles to restore their original look and functionality and are not original/genuine/OE/OEM/OES replacement parts. These items do not originate from the vehicle manufacturer and may be the subject of a design not owned by Abakus and the manufacturer of this spare part. They may only be used for repairs to restore the intended vehicle to its original appearance. Our products are delivered without instruction of installation. Installation of our product may only be carried out by trained specialist technicians in specific car repairs. Products supplied by us are exclusively intended for proper and appropriate use. The warranty may become invalid in the event of: improper installation or repair, unsuitable application or use, installation or repair made outside specialist car workshops. Warranty claims are lost if the vehicle is modified and used for motor sports, tuning or similar events (except our tuning parts which are described in TecDoc and on our price list). Warranty application should include complete documentation among others: chassis no., first registration, vehicle mileage, information about LPG installation, fault memory log, pictures, our QC (quality check) code, installation invoice, contact details of the car repair workshop performing the replacement or repair. Warranty application are available in our Client Panel system. Complaints may require supplementing data such as error memory logs. Incomplete documentation may result in rejection of the claim. Any damage caused during transport is not considered quality damage and will be considered on an individual basis. The product is intended for use within the performance limits specified by the manufacturer and should only be used by qualified personnel who have been trained to operate this product. Before each use, the product should be checked for damage or fixing of its parts and not used if any defects or loose parts are found. Failure to follow the manufacturer's guidelines could result in potential product damage or even injury. Wear appropriate protective clothing if necessary when working with the product.

• Engine Code: M 97.22
• Name: EP 1.957.006
• Manufacturer: EPS

• Diameter [mm]: 26
• Number of pins: 2
• Supplementary Article/Info 2: with seal ring
• Spring Design: Retaining Spring
• Length [mm]: 20
• Housing Colour: blue
• Height [mm]: 57
• Colour: grey
• Number of connectors: 2
• Manufacturer: VEMO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Engine Code: M 97.22
• Manufacturer: FACET

• Alternatively:
• Number of pins: 2
• Alternative Repair Kit: 550305
• Manufacturer: ERA

• Construction Year from: 01.2008
• Voltage [V]: 12
• Number of pins: 2
• Tightening Torque [Nm]: 20
• Supplementary Article/Info 2: without cable
• Corresponds to the original part in colour: black
• Plug Type: Blade Terminal
• Connector Shape: oval
• Assy./disassy. by qualified personnel required!:
• Name: HE 6PG013114341
• Manufacturer: HELLA

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Oxygen Sensor: Diagnostic Probe, Thread pre-greased
• Fabrication Number: ESL-SK-000
• Manufacturer: NTY
• Name: NTY ESL-SK-000

• Alternatively:
• Number of pins: 3
• Fitting Depth [mm]: 24
• Connector Shape: oval
• Manufacturer: ERA

• Construction Year to: 08.2008
• Temperature range from [°C]: -40
• Temperature range to [°C]: 130
• Manufacturer: BOSCH

• Engine Code: M 97.22
• Required quantity: 2
• Name: EP 1.953.387
• Manufacturer: EPS

• Oxygen Sensor: Regulating Sensor
• Number of circuits: 4
• Manufacturer: KAMOKA

• Engine Code: M 97.22
• Required quantity: 2
• Manufacturer: FACET

• Construction Year to: 08.2008
• Manufacturer: BOSCH
• Name: BS 0232103092

• Sensor Type: Hall Sensor
• Alternatively:
• Number of pins: 3
• Fitting Depth [mm]: 24
• Manufacturer: ERA

• Construction Year from: 11.2007
• Construction Year to: 11.2008
• Engine Code: M97.22
• Sensor Type: Hall Sensor
• Number of pins: 3
• Voltage [V]: 12
• Connector Shape: oval
• Supplementary Article/Info 2: without cable
• Manufacturer: VALEO
• Additional information: VA 253817
• Lisainfo: VA 253817

• Oxygen Sensor: Diagnostic Probe, Regulating Sensor
• Length [mm]: 750
• Number of connectors: 4
• Manufacturer: VERNET

Fitting Position: before catalytic converter, after catalytic converter

• Construction Year to: 08.2008
• Oxygen Sensor: Regulating Sensor, Diagnostic Probe
• Block Separation:
• Number of circuits: 4
• Recommended change interval [km]: 160,000
• Connector/Clamp: Connector may need adjustment
• Manufacturer: BOSCH

Fitting Position: before catalytic converter, after catalytic converter

• Oxygen Sensor: Diagnostic Probe
• Fitting Position: after catalytic converter
• Length [mm]: 750
• Technical Information Number: Universal 77015
• Manufacturer: FAE

• Fabrication Number: EPP-VW-011
• Recommended additional repairs: Air Filter
• Number of pins: 5
• Connector Shape: oval
• Housing Type: with housing
• Supplementary Article/Info 2: with integrated air temperature sensor
• Manufacturer: NTY
• Name: NTY EPP-VW-011

• Oxygen Sensor: Diagnostic Probe
• Number of pins: 4
• Cable Length [mm]: 1,040
• for OE number: 855378
• Manufacturer: MEAT&DORIA

• Construction Year to: 08.2008
• Oxygen Sensor: Diagnostic Probe
• Fitting Position: after catalytic converter
• Number of circuits: 4
• Overall Length [mm]: 790
• Available as universal article as well, see article no.: 0258986602
• Recommended change interval [km]: 250,000
• Manufacturer: BOSCH

• Oxygen Sensor: Switching-type Oxygen Sensor
• Voltage [V]: 12
• Colour: red
• Guarantee: 3 years guarantee
• Number of circuits: 5
• Weight [kg]: 0.15
• Operating Mode: Electric
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY
• Name: CE 09SKV905

• Oxygen Sensor: Switching-type Oxygen Sensor
• Guarantee: 3 years guarantee
• Weight [kg]: 0.15
• Always compare old and new part (in particular OE No.):
• Technical Information: Universal
• Manufacturer: SKV GERMANY
• Name: CE 09SKV915

• Construction Year to: 08.2008
• Oxygen Sensor: Regulating Sensor
• Fitting Position: before catalytic converter
• Number of circuits: 5
• Overall Length [mm]: 790
• Recommended change interval [km]: 250,000
• Manufacturer: BOSCH

• Construction Year to: 08.2008
• Recommended additional repairs: Air Filter
• Manufacturer: BOSCH