• Emission Standard: Euro 3 (D3)
• Oxygen Sensor: Diagnostic Probe, Thread pre-greased
• Fabrication Number: ESL-SK-000
• Manufacturer: NTY
• Name: NTY ESL-SK-000

• Emission Standard: Euro 3 (D3)
• Length [mm]: 410
• Fabrication Number: ESL-CT-007
• Manufacturer: NTY
• Name: NTY ESL-CT-007

Fitting Position: Front, before catalytic converter, after catalytic converter Oxygen Sensor: Regulating Probe, Diagnostic Probe, Thread pre-greased

• Oxygen Sensor: Regulating Probe, Thread pre-greased
• Connector/Clamp: Connector may need adjustment
• Number of circuits: 4
• Fitting Position: before catalytic converter
• Fabrication Number: ESL-UV-000
• Manufacturer: NTY

• Oxygen Sensor: Regulating Probe
• Number of circuits: 4
• Manufacturer: KAMOKA

• Construction Year from: 04.1999
• Fitting Position: before catalytic converter
• Manufacturer Restriction: Bosch
• not for manufacturer exhaust gas norm: EURO2000;CEE2000
• Block Separation:
• Construction Year to: 12.1996
• Oxygen Sensor: Regulating Probe, Heated
• for RPO number from: 7084
• for RPO number up to: 7329
• Engine Code: LFY (XU7JP4)
• Number of circuits: 4
• Overall Length [mm]: 410
• Name: LAMBDA ANDUR
• Manufacturer: MAX

• Technical Information Number: Universal
• Overall Length [mm]: 325
• Number of pins: 4
• Oxygen Sensor: Regulating Probe
• Manufacturer: ASHIKA
• Lisainfo: 43-U04
• Additional information: 43-U04

• Technical Information Number: Universal
• Overall Length [mm]: 325
• Number of pins: 4
• Oxygen Sensor: Regulating Probe
• Manufacturer: JAPKO

• for RPO number up to: 07083
• Line insulation design: with silicone-coated woven-fibre insulation
• Length [mm]: 570
• Oxygen Sensor: Regulating Probe, Thread pre-greased
• Weight [kg]: 0.144
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Oxygen Sensor: Diagnostic Probe
• Length [mm]: 1,500
• Fabrication Number: ESL-CT-018
• Manufacturer: NTY

• for facelift:
• Manufacturer Restriction: Bosch
• not for emission standard: CEE 2000
• Oxygen Sensor: Regulating Probe, Planar probe
• Exhaust System: before catalytic converter
• Number of pins: 4
• Length [mm]: 440
• Manufacturer: TOPRAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Construction Year from: 04.1999
• Oxygen Sensor: Regulating Probe, Heated
• for manufacturer exhaust gas norm: EURO2000;CEE2000
• Engine Code: LFY (XU7JP4)
• Fitting Position: before catalytic converter
• Number of circuits: 4
• Overall Length [mm]: 410
• Name: LAMBDA ANDUR
• Manufacturer: MAX

• Oxygen Sensor: Regulating Probe
• Emission Standard: Euro 3 (D3)
• Fitting Position: Front
• Length [mm]: 550
• Number of connectors: 4
• Manufacturer: VERNET

• Cable Length [mm]: 1,235
• Oxygen Sensor: Diagnostic Probe
• Number of circuits: 4
• Manufacturer: DELLO AUTOMEGA

• Construction Year from: 04.1999, 01.1997
• Oxygen Sensor: Regulating Probe, Heated
• Manufacturer Restriction: Bosch, SAGEM
• not for manufacturer exhaust gas norm: EURO2000;CEE2000
• Block Separation:
• Construction Year to: 12.1996, 03.1999
• for RPO number from: 7084, 7330
• for RPO number up to: 7329
• Engine Code: LFY (XU7JP4)
• Fitting Position: before catalytic converter
• Number of circuits: 4
• Connector/Clamp: Connector may need adjustment
• Name: LAMBDA ANDUR
• Manufacturer: MAX

• Oxygen Sensor: Regulating Probe, Oxygen Sensor
• Fitting Position: before catalytic converter
• Emission Standard: Euro 2
• Guarantee: 3 years guarantee
• Weight [kg]: 0.15
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY

• Fitting Position: before catalytic converter
• Oxygen Sensor: Regulating Probe, Planar probe
• Emission Standard: CEE 2000
• Number of pins: 4
• Length [mm]: 455
• Manufacturer: TOPRAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Construction Year from: 12.1996
• Line insulation design: with silicone-coated woven-fibre insulation
• Length [mm]: 400
• Number of connectors: 4
• Weight [kg]: 0.133
• Oxygen Sensor: Thread pre-greased
• Manufacturer: VEMO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Oxygen Sensor: Regulating Probe, Planar probe, Heated
• Emission Standard: Euro 2
• Fitting Position: before catalytic converter
• Cable Length [mm]: 525
• Name: LAMBDA ANDUR
• Manufacturer: DLP
• Quality class: PJ

Additional information: "Tootja: DELPHI
406 (8B), 10.95-05.0
(kvaliteediklass: PJ)" Lisainfo: "Tootja: DELPHI
406 (8B), 10.95-05.0
(kvaliteediklass: PJ)"

• Oxygen Sensor: Regulating Probe, Planar probe, Heated
• Emission Standard: Euro 3
• Fitting Position: before catalytic converter
• Cable Length [mm]: 370
• Name: LAMBDA ANDUR
• Manufacturer: DLP

• Oxygen Sensor: Regulating Probe, Planar probe, Heated
• Emission Standard: Euro 2
• Fitting Position: before catalytic converter
• Alternatively:
• Cable Length [mm]: 400
• Name: LAMBDA ANDUR
• Manufacturer: DLP

• Oxygen Sensor: Regulating Probe, Oxygen Sensor
• Voltage [V]: 12
• Length [mm]: 630
• Guarantee: 3 years guarantee
• Number of circuits: 4
• Weight [kg]: 0.11
• Operating Mode: Electric
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY
• Name: CE 09SKV042

• Construction Year from: 04.1999
• Oxygen Sensor: Regulating Probe, Diagnostic Probe, Heated
• for manufacturer exhaust gas norm: EURO2000;CEE2000
• Block Separation:
• Engine Code: LFY (XU7JP4)
• Number of circuits: 4
• Connector/Clamp: Connector may need adjustment
• Name: LAMBDA ANDUR
• Manufacturer: MAX
• Lisainfo: MGS-615
• Additional information: MGS-615

Fitting Position: after catalytic converter, before catalytic converter

• Oxygen Sensor: Regulating Probe, Planar probe, Heated
• Emission Standard: Euro 2
• Fitting Position: before catalytic converter
• Cable Length [mm]: 400
• Manufacturer: DELPHI
• Name: DE ES20272-12B1

• Oxygen Sensor: Regulating Probe, Heated
• External Thread Size: M18 x 1,5
• Spanner Size: 22
• Number of circuits: 4
• Cable Length [mm]: 570
• Weight [kg]: 0.102
• for OE number: 1628.8Z
• Manufacturer: FEBI

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• for manufacturer exhaust gas norm: EURO 2000, CEE 2000
• Oxygen Sensor: Regulating Probe
• Overall Length [mm]: 420
• Number of circuits: 4
• Guarantee: 5 years guarantee
• General Information: Sold in Hueco brand: printing and packaging
• Name: HU 135335
• Manufacturer: HITACHI

• Construction Year to: 12.1996
• Exhaust System: for pre-catalytic converter
• Quality: OE
• Manufacturer Restriction: DENSO
• Thread Size: M18x1.5
• Cable Length [mm]: 750
• Number of pins: 4
• Weight [g]: 100
• Gross Weight [g]: 149
• Manufacturer: DENSO
• Name: DN DOX-0120
• Quality class: Q

Oxygen Sensor: Regulating Probe, Heated, Finger probe, Oxygen Sensor Additional information: "Tootja: DENSO
164 (164), 01.87-09.
(kvaliteediklass: Q)" Lisainfo: "Tootja: DENSO
164 (164), 01.87-09.
(kvaliteediklass: Q)"

• Oxygen Sensor: Regulating Probe, Planar probe, Heated
• Emission Standard: Euro 2
• Fitting Position: before catalytic converter
• Cable Length [mm]: 380
• Name: LAMBDA ANDUR
• Manufacturer: DLP

• Fitting Position: Front, after catalytic converter
• Oxygen Sensor: Diagnostic Probe, Thread pre-greased
• Emission Standard: Euro 3 (D3)
• Line insulation design: with silicone-coated woven-fibre insulation
• Weight [kg]: 0.187
• Socket colour: blue
• Connector Shape: rectangular
• Number of pins: 4
• Thread Size: M18 x 1,5
• for OE number: 1628 HV
• Cable Length [mm]: 1,320
• Length [mm]: 1,490
• Number of circuits: 4
• Version: ZR PLANAR
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Oxygen Sensor: Regulating Probe, Heated
• Emission Standard: Euro 3
• Fitting Position: before catalytic converter
• Cable Length [mm]: 300
• Number of pins: 4
• Assy./disassy. by qualified personnel required!:
• Name: Lambda andur
• Manufacturer: HEL

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Construction Year from: 12.1996
• Exhaust System: for pre-catalytic converter
• Quality: OE
• Thread Size: M18x1.5
• Cable Length [mm]: 750
• Number of pins: 4
• Weight [g]: 103
• Gross Weight [g]: 152
• Manufacturer: DENSO
• Name: Lambda sensor
• Quality class: Q

Oxygen Sensor: Regulating Probe, Heated, Finger probe, Oxygen Sensor Additional information: "Tootja: DENSO
106 I (1A, 1C), 08.9
(kvaliteediklass: Q)" Lisainfo: "Tootja: DENSO
106 I (1A, 1C), 08.9
(kvaliteediklass: Q)"

• Oxygen Sensor: Regulating Probe, Heated
• External Thread Size: M18 x 1,5
• Spanner Size: 22
• Number of circuits: 4
• Cable Length [mm]: 570
• Weight [kg]: 0.102
• for OE number: 1628.8Z
• Name: SW 33 10 3127
• Manufacturer: SWAG

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Oxygen Sensor: Regulating Probe, Planar probe, Heated
• Emission Standard: Euro 2
• Fitting Position: before catalytic converter
• Cable Length [mm]: 630
• Manufacturer: DELPHI
• Name: DE ES20234-12B1

• Oxygen Sensor: Regulating Probe, Planar probe, Heated
• Emission Standard: Euro 2
• Fitting Position: before catalytic converter
• Cable Length [mm]: 530
• Name: LAMBDA ANDUR
• Manufacturer: DLP

• Conductor Number: 4
• Number of circuits: 4
• Length [mm]: 400
• Resistor [Ohm]: 9
• Cable Length [mm]: 400
• Oxygen Sensor: Heated
• Manufacturer: MAGNETI MARELLI

• Oxygen Sensor: Heated
• Thread Size: M18 x 1,5
• Number of pins: 4
• Connector Shape: rectangular
• Overall Length [mm]: 600
• Manufacturer: AIC

General Information: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.

• Construction Year from: 04.1999
• Oxygen Sensor: Regulating Probe
• Fitting Position: before catalytic converter
• Emission Standard: CEE 2000
• Number of circuits: 4
• Overall Length [mm]: 410
• Available as universal article as well, see article no.: 0258986615
• Recommended change interval [km]: 160,000
• Name: LAMBDA ANDUR
• Manufacturer: BOS

• Oxygen Sensor: Regulating Probe
• Construction Year to: 12.1996
• Length [mm]: 400
• Number of pins: 4
• Technical Information Number: Universal 77008
• Manufacturer: FAE

• Construction Year to: 12.1996
• Exhaust System: for pre-catalytic converter
• for OE number: 16287S
• Quality: OE
• Manufacturer Restriction: DENSO
• Thread Size: M18x1.5
• Cable Length [mm]: 540
• Number of pins: 4
• Weight [g]: 103
• Gross Weight [g]: 133
• Manufacturer: DENSO
• Name: DN DOX-1535

Oxygen Sensor: Regulating Probe, Heated, Finger probe, Oxygen Sensor

• Construction Year from: 04.1999, 01.1997
• Oxygen Sensor: Regulating Probe
• Fitting Position: before catalytic converter
• Manufacturer Restriction: Bosch, SAGEM
• not for emission standard: CEE 2000
• Block Separation:
• Construction Year to: 12.1996, 03.1999
• for RPO number from: 7084, 7330
• for RPO number up to: 7329
• Number of circuits: 4
• Recommended change interval [km]: 160,000
• Connector/Clamp: Connector may need adjustment
• Name: LAMBDA ANDUR
• Manufacturer: BOS

• for RPO number up to: 07083
• Line insulation design: with silicone-coated woven-fibre insulation
• Connector Shape: round
• Conductor Number: 4
• Cable Length [mm]: 450
• Thread Size: M18 x 1,5
• Length [mm]: 570
• Version: ZR-PLANAR
• Weight [kg]: 0.143
• Oxygen Sensor: Thread pre-greased
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Length [mm]: 1,520
• Number of circuits: 4
• Conductor Number: 4
• Resistor [Ohm]: 9
• Cable Length [mm]: 1,520
• Oxygen Sensor: Heated
• Name: LAMBDA ANDUR
• Manufacturer: MAG

• Engine Code: LFY (XU7JP4)
• Line insulation design: with silicone-coated woven-fibre insulation
• Supplementary Article/Info 2: without plug
• Number of pins: 4
• for OE number: V99760001
• Cable Length [mm]: 210
• Number of circuits: 4
• Weight [kg]: 0.09
• Length [mm]: 350
• Fitting Position: after catalytic converter
• Manufacturer: VEMO GERMANY

Oxygen Sensor: Regulating Probe, Finger probe, Heated, Thread pre-greased General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Construction Year from: 04.1999
• Oxygen Sensor: Regulating Probe, Diagnostic Probe
• Emission Standard: CEE 2000
• Block Separation:
• Number of circuits: 4
• Recommended change interval [km]: 160,000
• Connector/Clamp: Connector may need adjustment
• Name: LAMBDA ANDUR
• Manufacturer: BOS

Fitting Position: before catalytic converter, after catalytic converter

• Construction Year to: 12.1996
• Fitting Position: before catalytic converter
• Line insulation design: with silicone-coated woven-fibre insulation
• Oxygen Sensor: Planar probe, Heated, Thread pre-greased
• Supplementary Article/Info 2: without plug
• Cable Length [mm]: 210
• Number of circuits: 4
• Weight [kg]: 0.09
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Emission Standard: Euro 2
• Oxygen Sensor: Diagnostic Probe, Heated
• External Thread Size: M18 x 1,5
• Spanner Size: 22
• Number of circuits: 4
• Cable Length [mm]: 1,500
• Weight [kg]: 0.135
• for OE number: 1628.HQ
• Name: SW 33 10 3160
• Manufacturer: SWAG

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Oxygen Sensor: Regulating Probe
• Emission Standard: Euro 2
• Fitting Position: Front
• Length [mm]: 640
• Number of connectors: 4
• Manufacturer: VERNET

• Fitting Position: after catalytic converter
• Cable Length [mm]: 1,235
• Oxygen Sensor: Planar probe, Heated
• Manufacturer: DELPHI
• Name: DE ES20307-12B1

• Oxygen Sensor: Regulating Probe, Planar probe, Heated
• Emission Standard: Euro 2
• Fitting Position: before catalytic converter
• Cable Length [mm]: 540
• Manufacturer: DELPHI
• Name: DE ES20258-12B1

• Oxygen Sensor: Regulating Probe
• Construction Year from: 12.1996
• for manufacturer exhaust gas norm: L3
• Length [mm]: 450
• Number of pins: 4
• Technical Information Number: Universal 77008
• Manufacturer: FAE

• Construction Year from: 04.1999
• Oxygen Sensor: Diagnostic Probe
• Fitting Position: after catalytic converter
• Emission Standard: CEE 2000
• Number of circuits: 4
• Overall Length [mm]: 1,510
• Available as universal article as well, see article no.: 0258986615
• Recommended change interval [km]: 160,000
• Name: LAMBDA ANDUR
• Manufacturer: BOS

• Construction Year from: 12.1996
• Exhaust System: for pre-catalytic converter
• for OE number: 16287R
• Quality: OE
• Manufacturer Restriction: DENSO
• Thread Size: M18x1.5
• Cable Length [mm]: 545
• Number of pins: 4
• Weight [g]: 102
• Gross Weight [g]: 132
• Manufacturer: DENSO

Oxygen Sensor: Regulating Probe, Heated, Finger probe, Oxygen Sensor

• Oxygen Sensor: Regulating Probe, Heated
• Emission Standard: Euro 2
• Fitting Position: before catalytic converter
• Required quantity: 1
• Cable Length [mm]: 390
• Number of pins: 4
• Assy./disassy. by qualified personnel required!:
• Name: Lambda andur
• Manufacturer: HEL

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Oxygen Sensor: Regulating Probe, Heated
• Construction Year from: 04.1999
• for manufacturer exhaust gas norm: EURO 2000, CEE 2000
• Length [mm]: 410
• Technical Information Number: Universal 77015
• Manufacturer: FAE

• Oxygen Sensor: Diagnostic Probe, Heated
• Construction Year from: 04.1999
• for manufacturer exhaust gas norm: EURO 2000, CEE 2000
• Length [mm]: 1,520
• Number of pins: 4
• Technical Information Number: Universal 77015
• Socket colour: blue
• Manufacturer: FAE

• Engine Code: LFY (XU7JP4)
• Fitting Position: after catalytic converter
• Emission Standard: Euro 3
• Length [mm]: 1,500
• Cable Length [mm]: 1,500
• Conductor Number: 4
• Available as universal article as well, see article no.: 1.998.240
• Number of circuits: 4
• Name: EP 1.998.301
• Manufacturer: EPS

Oxygen Sensor: Diagnostic Probe, Heated, Planar probe, Thread pre-greased

• Construction Year from: 04.1999
• Oxygen Sensor: Regulating Probe
• Fitting Position: before catalytic converter
• Manufacturer Restriction: Bosch
• not for emission standard: CEE 2000
• Block Separation:
• Construction Year to: 12.1996
• for RPO number from: 7084
• for RPO number up to: 7329
• Number of circuits: 4
• Overall Length [mm]: 410
• Available as universal article as well, see article no.: 0258986506
• Recommended change interval [km]: 100,000
• Name: LAMBDA ANDUR
• Manufacturer: BOS

• Construction Year to: 04.1999
• Oxygen Sensor: Diagnostic Probe, Planar probe
• Emission Standard: Euro 3 (D3)
• Number of pins: 4
• Cable Length [mm]: 1,370
• for OE number: 1628HQ
• Manufacturer: MEAT&DORIA

• Engine Code: LFY (XU7JP4)
• Fuel Type: Petrol/Gas
• Emission Standard: Euro 2
• Oxygen Sensor: Regulating Probe, Heated
• Voltage [V]: 12
• Conductor Number: 4
• Cable Length [mm]: 400
• Manufacturer: PIERBURG

• Engine Code: LFY (XU7JP4)
• Emission Standard: Euro 3
• Oxygen Sensor: Diagnostic Probe, Heated
• Voltage [V]: 12
• Conductor Number: 4
• Cable Length [mm]: 1,640
• Manufacturer: PIERBURG

• Oxygen Sensor: Regulating Probe, Heated
• Emission Standard: Euro 2
• Fitting Position: before catalytic converter
• Required quantity: 1
• Cable Length [mm]: 530
• Number of pins: 4
• Assy./disassy. by qualified personnel required!:
• Name: HE 6PA358103391
• Manufacturer: HELLA

Brief Information: *** HELLA Electronics OE competence for over 60 years.