• Number of pins: 2
• Name: ANDUR,SISENDOHU TEMPERATUUR
• Manufacturer: MAX

• Engine Code: 6FZ (EW7J4)
• Corresponds to the original part in colour: brown, green
• Name: ANDUR,SISENDOHU TEMPERATUUR
• Manufacturer: EPS
• Additional information: 1-994-005
• Lisainfo: 1-994-005

• Manufacturer: VERNET
• Additional information: AS0006 VERNET
• Lisainfo: AS0006 VERNET

• Number of connectors: 2
• Weight [kg]: 0.01
• Name: ANDUR,SISENDOHU TEMPERATUUR
• Manufacturer: FEB

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Number of connectors: 2
• Weight [kg]: 0.007
• Manufacturer: BLUE PRINT ELEKTRYKA

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Engine Code: 6FZ (EW7J4)
• Colour: green
• Thread Size: M12x1,5
• Spanner Size: 19
• Manufacturer: FACET

• Engine Code: 6FZ (EW7J4)
• Colour: green
• Thread Size: M12x1,5
• Spanner Size: 19
• Manufacturer: FACET
• Name: EP 1.830.276

• Thread Size: M12 x 1,5
• Spanner Size: 19
• Supplementary Article/Supplementary Info: with gasket/seal
• Number of pins: 2
• Weight [kg]: 0.035
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Number of pins: 3
• for OE number: 1920 AN
• Manufacturer: ABAKUS LORO

General Information: The following information is for general and informational purposes only and does not constitute warranty terms. Warranty terms and conditions are available from our dealers and in our general terms and conditions of sale. Abakus spare/repair parts are intended only for vehicle repairs in order to restore their original functionality. Abakus spare/repair parts are used or sold to users only for the purpose of repairing vehicles to restore their original look and functionality and are not original/genuine/OE/OEM/OES replacement parts. These items do not originate from the vehicle manufacturer and may be the subject of a design not owned by Abakus and the manufacturer of this spare part. They may only be used for repairs to restore the intended vehicle to its original appearance. Our products are delivered without instruction of installation. Installation of our product may only be carried out by trained specialist technicians in specific car repairs. Products supplied by us are exclusively intended for proper and appropriate use. The warranty may become invalid in the event of: improper installation or repair, unsuitable application or use, installation or repair made outside specialist car workshops. Warranty claims are lost if the vehicle is modified and used for motor sports, tuning or similar events (except our tuning parts which are described in TecDoc and on our price list). Warranty application should include complete documentation among others: chassis no., first registration, vehicle mileage, information about LPG installation, fault memory log, pictures, our QC (quality check) code, installation invoice, contact details of the car repair workshop performing the replacement or repair. Warranty application are available in our Client Panel system. Complaints may require supplementing data such as error memory logs. Incomplete documentation may result in rejection of the claim. Any damage caused during transport is not considered quality damage and will be considered on an individual basis. The product is intended for use within the performance limits specified by the manufacturer and should only be used by qualified personnel who have been trained to operate this product. Before each use, the product should be checked for damage or fixing of its parts and not used if any defects or loose parts are found. Failure to follow the manufacturer's guidelines could result in potential product damage or even injury. Wear appropriate protective clothing if necessary when working with the product.

• Fabrication Number: ECP-CT-024
• Sensor Type: Hall Sensor
• Number of pins: 3
• Supplementary Article/Info 2: without cable
• Connector Shape: rectangular
• Manufacturer: NTY

• Fabrication Number: ESS-CT-001
• Manufacturer: NTY

• Number of pins: 2
• for manufacturer number: 6PT 009 109-221
• Assy./disassy. by qualified personnel required!:
• Name: HE 6PT009109221
• Manufacturer: HELLA

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Engine Code: 6FZ (EW7J4)
• Manufacturer: FACET

• Engine Code: 6FZ (EW7J4)
• Name: DETONATSIOONIANDUR
• Manufacturer: EPS

• Vehicle Equipment: for vehicles without gas operation
• Number of pins: 3
• Name: ANDUR,OHUVOTU ROHK
• Manufacturer: MAX

• Number of pins: 2
• Manufacturer: FAE

• Number of pins: 3
• Voltage [V]: 12
• Name: ANDUR,OHUVOTU ROHK
• Manufacturer: MAX

• Height [mm]: 20.3
• Sensor Type: Hall Sensor
• Number of connectors: 3
• Manufacturer: VERNET

• Oxygen Sensor: Diagnostic Probe, Thread pre-greased
• Fabrication Number: ESL-SK-000
• Manufacturer: NTY
• Name: NTY ESL-SK-000

• Number of connectors: 2
• Weight [kg]: 0.037
• for OE number: 5946.31
• Manufacturer: FEBI BILSTEIN

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Alternatively:
• Number of pins: 3
• Fitting Depth [mm]: 20
• Housing Colour: grey
• Weight [kg]: 0.018
• Alternative Repair Kit: 550010
• Manufacturer: ERA

• Number of pins: 3
• Pressure from [kPA]: 20
• Pressure to [kPA]: 105
• for OE number: 9639418880
• Manufacturer: MEAT&DORIA

Manufacturer: BOSCH

• Voltage [V]: 12
• Number of pins: 2
• Tightening Torque [Nm]: 20
• Supplementary Article/Info 2: without cable
• Corresponds to the original part in colour: black
• Plug Type: Blade Terminal
• Connector Shape: Square
• Assy./disassy. by qualified personnel required!:
• Manufacturer: HELLA
• Name: HE 6PG013114411

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Engine Code: 6FZ (EW7J4)
• Colour: black
• Number of pins: 2
• Manufacturer: VDO

• Measuring Range from [kPa]: 15
• Measuring Range to [kPa]: 100
• Measuring Range from [V]: 0.21
• Measuring Range to [V]: 4.75
• Number of connectors: 3
• Manufacturer: VERNET

• Engine Code: 6FZ (EW7J4)
• Manufacturer: FACET

• Engine Code: 6FZ (EW7J4)
• Name: ANDUR,NUKKVOLLIPOSITSIOON
• Manufacturer: EPS

• Voltage [V]: 12
• Number of pins: 3
• Rotation Direction: Clockwise rotation
• Number of mounting bores: 2
• Assy./disassy. by qualified personnel required!:
• Manufacturer: HELLA
• Name: HE 6PX008476771

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Length [mm]: 54.5
• Number of connectors: 3
• Weight [kg]: 0.02
• Manufacturer: FEBI BILSTEIN
• Additional information: 31239 NRF
• Lisainfo: 31239 NRF

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Oxygen Sensor: Regulating Probe, Oxygen Sensor
• Fitting Position: before catalytic converter
• Number of circuits: 4
• Connector/Clamp: Connector may need adjustment
• Name: LAMBDA ANDUR
• Manufacturer: MAX

• Number of pins: 2
• Name: DE AS10174
• Manufacturer: DELPHI

• Line insulation design: with silicone-coated woven-fibre insulation
• Length [mm]: 570
• Oxygen Sensor: Regulating Probe, Thread pre-greased
• Weight [kg]: 0.144
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Length [mm]: 54.5
• Number of connectors: 3
• Weight [kg]: 0.02
• Name: SW 62 93 1239
• Manufacturer: SWAG

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Number of pins: 3
• Pressure from [kPA]: 20
• Name: ANDUR,OHUVOTU ROHK
• Manufacturer: DLP

• Voltage [V]: 12
• Corresponds to the original part in colour: grey
• Sensor Type: Hall Sensor
• Number of pins: 3
• Supplementary Article/Info 2: without cable
• Colour Coding: black
• Assy./disassy. by qualified personnel required!:
• Manufacturer: HELLA

Brief Information: *** HELLA Electronics OE competence for over 60 years.

Manufacturer: BOSCH

• Fitting Position: after catalytic converter
• Line insulation design: with silicone-coated woven-fibre insulation
• Weight [kg]: 0.117
• Oxygen Sensor: Thread pre-greased
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Oxygen Sensor: Diagnostic Probe, Heated
• Fitting Position: after catalytic converter
• Number of circuits: 4
• Connector/Clamp: Connector may need adjustment
• Name: LAMBDA ANDUR
• Manufacturer: MAX

• Oxygen Sensor: Regulating Probe, Oxygen Sensor
• Fitting Position: before catalytic converter
• Guarantee: 3 years guarantee
• Weight [kg]: 0.15
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY

• Oxygen Sensor: Regulating Probe
• Fitting Position: before catalytic converter
• Number of circuits: 4
• Recommended change interval [km]: 160,000
• Connector/Clamp: Connector may need adjustment
• Manufacturer: ENERGY

• Number of pins: 3
• Fitting Depth [mm]: 20
• Housing Colour: grey
• Weight [kg]: 0.018
• Manufacturer: ERA

• Oxygen Sensor: Regulating Probe, Planar probe, Heated
• Fitting Position: before catalytic converter
• Cable Length [mm]: 525
• Name: LAMBDA ANDUR
• Manufacturer: DLP
• Quality class: PJ

Additional information: "Tootja: DELPHI
406 (8B), 10.95-05.0
(kvaliteediklass: PJ)" Lisainfo: "Tootja: DELPHI
406 (8B), 10.95-05.0
(kvaliteediklass: PJ)"

• Number of pins: 3
• Name: ANDUR,NUKKVOLLIPOSITSIOON
• Manufacturer: DLP

• Number of pins: 3
• Pressure from [kPA]: 15
• Pressure to [kPA]: 100
• Manufacturer: FAE

• Pressure [Pa] from: 20,000
• Pressure [Pa] to: 100,000
• Voltage [V]: 5
• Number of pins: 3
• Assy./disassy. by qualified personnel required!:
• Name: HE 6PP009400221
• Manufacturer: HELLA

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Oxygen Sensor: Regulating Probe, Planar probe, Heated
• Fitting Position: before catalytic converter
• Cable Length [mm]: 380
• Name: LAMBDA ANDUR
• Manufacturer: DLP

• Oxygen Sensor: Regulating Probe
• Fitting Position: before catalytic converter
• Length [mm]: 540
• Number of connectors: 4
• Manufacturer: VERNET

• Oxygen Sensor: Regulating Probe, Planar probe, Heated
• Fitting Position: before catalytic converter
• Cable Length [mm]: 530
• Name: LAMBDA ANDUR
• Manufacturer: DLP

• Operating Mode: pneumatic
• Name: ANDUR,OHUVOTU ROHK
• Manufacturer: PIE

• Oxygen Sensor: Regulating Probe
• Fitting Position: before catalytic converter
• Number of circuits: 4
• Recommended change interval [km]: 160,000
• Connector/Clamp: Connector may need adjustment
• Name: LAMBDA ANDUR
• Manufacturer: BOS

• Fitting Position: after catalytic converter
• Emission Standard: Euro 3, Euro 4
• Oxygen Sensor: Diagnostic Probe, Heated
• External Thread Size: M18 x 1,5
• Spanner Size: 22
• Number of circuits: 4
• Cable Length [mm]: 1,300
• Weight [kg]: 0.154
• Name: SW 33 10 3128
• Manufacturer: SWAG

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Oxygen Sensor: Diagnostic Probe
• Fitting Position: after catalytic converter
• Number of circuits: 4
• Recommended change interval [km]: 160,000
• Connector/Clamp: Connector may need adjustment
• Name: LAMBDA ANDUR
• Manufacturer: BOS

• Engine Code: 6FZ (EW7J4)
• Manufacturer Restriction: HELLA
• Pressure from [kPA]: 15
• Pressure to [kPA]: 102
• Output Voltage, from [V]: 0.261
• Output Voltage, up to [V]: 4.958
• Manufacturer: FACET

• Engine Code: 6FZ (EW7J4)
• Manufacturer Restriction: HELLA
• Pressure from [kPA]: 15
• Pressure to [kPA]: 102
• Output Voltage, from [V]: 0.261
• Output Voltage, up to [V]: 4.958
• Name: EP 1.993.001
• Manufacturer: EPS

• Line insulation design: with silicone-coated woven-fibre insulation
• Connector Shape: round
• Conductor Number: 4
• Cable Length [mm]: 450
• Thread Size: M18 x 1,5
• Length [mm]: 570
• Version: ZR-PLANAR
• Weight [kg]: 0.143
• Oxygen Sensor: Thread pre-greased
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Fitting Position: Front, before catalytic converter
• Oxygen Sensor: Regulating Probe, Heated, Thread pre-greased
• Line insulation design: with silicone-coated woven-fibre insulation
• Number of pins: 4
• Number of circuits: 4
• Socket colour: green
• Connector Shape: rectangular
• Thread Size: M18 x 1,5
• Weight [kg]: 0.138
• for OE number: 96 369 687 80
• Cable Length [mm]: 500
• Length [mm]: 600
• Number of connectors: 4
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Oxygen Sensor: Regulating Probe, Heated
• Fitting Position: before catalytic converter
• Cable Length [mm]: 600
• Number of pins: 4
• Assy./disassy. by qualified personnel required!:
• Name: Lambda andur
• Manufacturer: HEL

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Oxygen Sensor: Regulating Probe, Planar probe, Heated
• Fitting Position: before catalytic converter
• Cable Length [mm]: 540
• Manufacturer: DELPHI
• Name: DE ES20258-12B1

• Engine Code: 6FZ (EW7J4)
• Fitting Position: before catalytic converter
• Switching Capacity [W]: 10
• Length [mm]: 565
• Cable Length [mm]: 570
• Conductor Number: 4
• Available as universal article as well, see article no.: 10.7007
• Number of circuits: 4
• Manufacturer: FACET

Oxygen Sensor: Regulating Probe, Heated, Planar probe, Thread pre-greased

• Engine Code: 6FZ (EW7J4)
• Fitting Position: before catalytic converter
• Switching Capacity [W]: 10
• Length [mm]: 565
• Cable Length [mm]: 570
• Conductor Number: 4
• Available as universal article as well, see article no.: 1.997.007
• Number of circuits: 4
• Name: LAMBDA ANDUR
• Manufacturer: EPS

Oxygen Sensor: Regulating Probe, Heated, Planar probe, Thread pre-greased

• Oxygen Sensor: Diagnostic Probe, Planar probe, Heated
• Fitting Position: after catalytic converter
• Cable Length [mm]: 1,410
• Name: DE ES20309-12B1
• Manufacturer: DELPHI

• Oxygen Sensor: Regulating Probe
• Fitting Position: before catalytic converter
• Number of circuits: 4
• Manufacturer: BOSCH

• Oxygen Sensor: Diagnostic Probe
• Length [mm]: 1,240
• Number of connectors: 4

• Oxygen Sensor: Regulating Probe, Heated
• Fitting Position: before catalytic converter
• Cable Length [mm]: 530
• Number of pins: 4
• Assy./disassy. by qualified personnel required!:
• Name: HE 6PA358103391
• Manufacturer: HELLA

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Vehicle Equipment: for vehicles without gas operation
• Name: ANDUR,OHUVOTU ROHK
• Manufacturer: BOS

• Sensor Type: Hall Sensor
• Mounting Type: Screw Connection
• Shape: rectangular
• Number of pins: 3
• Supplementary Article/Info 2: with seal ring