• Oxygen Sensor: Diagnostic Probe, Thread pre-greased
• Fabrication Number: ESL-SK-000
• Manufacturer: NTY
• Name: NTY ESL-SK-000

• Length [mm]: 300
• Fitting Position: Front, after catalytic converter
• Oxygen Sensor: Diagnostic Probe, Thread pre-greased
• Fabrication Number: ESL-PL-008
• Manufacturer: NTY

• Fitting Position: Front, before catalytic converter
• Oxygen Sensor: Regulating Sensor, Thread pre-greased
• Fabrication Number: ESL-PL-000
• Manufacturer: NTY

• Length [mm]: 325
• Fabrication Number: ESL-PL-011
• Manufacturer: NTY

Fitting Position: Front, before catalytic converter, after catalytic converter Oxygen Sensor: Regulating Sensor, Diagnostic Probe, Thread pre-greased

• Oxygen Sensor: Regulating Sensor
• Number of circuits: 4
• Manufacturer: KAMOKA

• Vehicle Identification Number (VIN) to: 63000001
• Oxygen Sensor: Regulating Sensor, Heated
• Fitting Position: before catalytic converter
• Cable Length [mm]: 575
• Number of pins: 4
• Number of circuits: 4
• Thread Size: M 18x1,5
• Connector Shape: oval
• for OE number: 9193654
• Manufacturer: DELLO AUTOMEGA

• Engine Number to: 53999999, 54999999, 56999999
• Number of circuits: 4
• Cable Length [mm]: 580
• Oxygen Sensor: Regulating Sensor
• Manufacturer: JP GROUP
• Lisainfo: Lambda sensor
• Additional information: Lambda sensor

• Oxygen Sensor: Switching-type Oxygen Sensor
• Voltage [V]: 12
• Number of circuits: 4
• Weight [kg]: 0.09
• Resistor [Ohm]: 9
• Operating Mode: Electric
• Always compare old and new part (in particular OE No.):
• Manufacturer: ENERGY

• Vehicle Identification Number (VIN) to: 16079019
• Oxygen Sensor: Regulating Sensor, Finger-type Sensor
• Fitting Position: before catalytic converter
• Number of circuits: 4
• Length [mm]: 295
• Name: LAMBDA ANDUR
• Manufacturer: MAX

• Engine Code: Z 12 XEP
• Oxygen Sensor: Regulating Sensor, Heated
• Number of circuits: 4
• Length [mm]: 525
• Name: LAMBDA ANDUR
• Manufacturer: MAX

• Fitting Position: after catalytic converter
• Oxygen Sensor: Diagnostic Probe
• Manufacturer: DELLO AUTOMEGA

• Engine Number from: 63000001, 64000001, 66000001
• Oxygen Sensor: Diagnostic Probe
• Lisainfo: Lambda sensor
• Additional information: Lambda sensor

• Oxygen Sensor: Diagnostic Probe
• Fitting Position: after catalytic converter
• Number of circuits: 4
• Overall Length [mm]: 300
• Name: LAMBDA ANDUR
• Manufacturer: MAX

• Oxygen Sensor: Switching-type Oxygen Sensor
• Voltage [V]: 12
• Guarantee: 3 years guarantee
• Number of circuits: 4
• Weight [kg]: 0.09
• Resistor [Ohm]: 9
• Operating Mode: Electric
• Always compare old and new part (in particular OE No.):
• Manufacturer: ESEN SKV

• Block Separation:
• Number of circuits: 4
• Connector/Clamp: Connector may need adjustment
• Transmission Type: Manual Transmission
• Name: LAMBDA ANDUR
• Manufacturer: MAX

Oxygen Sensor: Regulating Sensor, Diagnostic Probe, Finger-type Sensor Fitting Position: before catalytic converter, after catalytic converter

• Oxygen Sensor: Diagnostic Probe, Switching-type Oxygen Sensor
• Engine Code: Z 12 XEP
• Voltage [V]: 12
• Length [mm]: 290
• Guarantee: 3 years guarantee
• Number of circuits: 4
• Weight [kg]: 0.09
• Operating Mode: Electric
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY
• Name: CE 09SKV073

• Oxygen Sensor: Regulating Sensor
• Engine Code: Z 12 XEP
• Voltage [V]: 12
• Length [mm]: 741
• Guarantee: 3 years guarantee
• Number of circuits: 4
• Weight [kg]: 0.11
• Operating Mode: Electric
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY
• Name: CE 09SKV072

• Oxygen Sensor: Regulating Sensor
• Fitting Position: Front, Upper
• Vehicle Identification Number (VIN) to: 16079019
• Length [mm]: 400
• Number of connectors: 4
• Manufacturer: VERNET

• Fitting Position: after catalytic converter
• Oxygen Sensor: Diagnostic Probe, Heated
• External Thread Size: M18 x 1,5
• Spanner Size: 22
• Number of circuits: 4
• Cable Length [mm]: 300
• Weight [kg]: 0.116
• Manufacturer: FEBI BILSTEIN

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Oxygen Sensor: Diagnostic Probe, Regulating Sensor
• Guarantee: 5 years guarantee
• Overall Length [mm]: 360
• Number of circuits: 4
• General Information: Sold in Hueco brand: printing and packaging
• Name: HU 135331
• Manufacturer: HITACHI

• Fitting Position: after catalytic converter
• Block Separation:
• Engine Code: Z 12 XEP
• Cable Length [mm]: 520
• Name: LAMBDA ANDUR
• Manufacturer: DLP

Oxygen Sensor: Diagnostic Probe, Regulating Sensor, Planar Sensor, Heated Additional information: "Tootja: DELPHI
ASTRA F CLASSIC KOMB
(kvaliteediklass: PJ)" Lisainfo: "Tootja: DELPHI
ASTRA F CLASSIC KOMB
(kvaliteediklass: PJ)"

• Oxygen Sensor: Diagnostic Probe, Unheated
• Number of pins: 4
• Cable Length [mm]: 520
• Quality: OE EQUIVALENT
• for OE number: 025198484
• Manufacturer: MEAT&DORIA

• Resistor [Ohm]: 9
• Length [mm]: 275
• Number of circuits: 4
• Conductor Number: 4
• Cable Length [mm]: 275
• Oxygen Sensor: Heated
• Name: LAMBDA ANDUR
• Manufacturer: MAG

• Length [mm]: 575
• Number of circuits: 4
• Conductor Number: 4
• Resistor [Ohm]: 9
• Cable Length [mm]: 575
• Oxygen Sensor: Heated
• Manufacturer: MAGNETI MARELLI
• Name: MM OSM015

• Oxygen Sensor: Regulating Sensor, Heated
• External Thread Size: M18 x 1,5
• Spanner Size: 22
• Number of circuits: 4
• Cable Length [mm]: 220
• Weight [kg]: 0.067
• Name: SW 33 10 3205
• Manufacturer: SWAG

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Oxygen Sensor: Regulating Sensor
• Voltage [V]: 12
• Length [mm]: 632
• Guarantee: 3 years guarantee
• Number of circuits: 4
• Weight [kg]: 0.14
• Resistor [Ohm]: 9
• Operating Mode: Electric
• Always compare old and new part (in particular OE No.):
• Name: CE 09SKV710
• Manufacturer: ESEN SKV

• Oxygen Sensor: Regulating Sensor
• Fitting Position: Front, Upper
• Vehicle Identification Number (VIN) from: 16079020
• Vehicle Identification Number (VIN) to: 56999999
• Length [mm]: 750
• Number of connectors: 4
• Manufacturer: VERNET

• Fitting Position: Front, Upper, before catalytic converter
• Vehicle Identification Number (VIN) to: 56999999
• Vehicle Identification Number (VIN) from: 16079020
• Block Separation:
• Engine Code: Z 12 XEP
• Cable Length [mm]: 300
• Name: LAMBDA ANDUR
• Manufacturer: DLP

Oxygen Sensor: Regulating Sensor, Diagnostic Probe, Planar Sensor, Heated Additional information: "Tootja: DELPHI
VECTRA C GTS, 08.02-
(kvaliteediklass: PJ)" Lisainfo: "Tootja: DELPHI
VECTRA C GTS, 08.02-
(kvaliteediklass: PJ)"

• Oxygen Sensor: Diagnostic Probe, Thread pre-greased
• Fitting Position: after catalytic converter
• Line insulation design: with silicone-coated woven-fibre insulation
• Overall Length [mm]: 448
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Fitting Position: Front, Upper, before catalytic converter
• Vehicle Identification Number (VIN) from: 16079020
• Vehicle Identification Number (VIN) to: 56999999
• Oxygen Sensor: Regulating Sensor
• Cable Length [mm]: 570
• Exhaust System: before catalytic converter
• Number of pins: 4
• Assy./disassy. by qualified personnel required!:
• Name: Lambda andur
• Manufacturer: HEL

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Vehicle Identification Number (VIN) to: 53999999, 54999999, 56999999
• Fitting Position: before catalytic converter
• Line insulation design: with silicone-coated woven-fibre insulation
• Oxygen Sensor: Planar Sensor, Heated, Thread pre-greased
• Supplementary Article/Info 2: without plug
• Cable Length [mm]: 210
• Number of circuits: 4
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Oxygen Sensor: Regulating Sensor, Diagnostic Probe
• Block Separation:
• Number of circuits: 4
• Recommended change interval [km]: 160,000
• Connector/Clamp: Connector may need adjustment
• Name: LAMBDA ANDUR
• Manufacturer: BOS

Fitting Position: before catalytic converter, after catalytic converter

• Exhaust System: for pre-catalytic converter
• Thread Size: M18x1.5
• Cable Length [mm]: 750
• Number of pins: 4
• Manufacturer Restriction: DENSO
• Quality: OE
• Weight [g]: 93
• Gross Weight [g]: 140
• Manufacturer: DENSO
• Name: Lambda sensor
• Quality class: Q

Oxygen Sensor: Regulating Sensor, Heated, Planar Sensor, Thread pre-greased, Switching-type Oxygen Sensor Additional information: "Tootja: DENSO
(kvaliteediklass: Q)" Lisainfo: "Tootja: DENSO
(kvaliteediklass: Q)"

• Fitting Position: Front, Upper, before catalytic converter
• Oxygen Sensor: Regulating Sensor, Heated
• Vehicle Identification Number (VIN) to: 16079019
• Cable Length [mm]: 350
• Number of pins: 4
• Assy./disassy. by qualified personnel required!:
• Name: Lambda andur
• Manufacturer: HEL

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Fitting Position: Front
• Line insulation design: with silicone-coated woven-fibre insulation
• Thread Size: M18 x 1,5
• Socket colour: black
• Oxygen Sensor: Heated, Thread pre-greased
• Connector Shape: oval
• Number of pins: 4
• for OE number: 08 55 402
• Length [mm]: 580
• Width [mm]: 32
• Height [mm]: 22
• Cable Length [mm]: 300
• Number of circuits: 4
• Version: Zr
• Manufacturer: VEMO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Oxygen Sensor: Regulating Sensor
• Guarantee: 5 years guarantee
• Overall Length [mm]: 560
• Number of circuits: 4
• General Information: Sold in Hueco brand: printing and packaging
• Name: HU 135325
• Manufacturer: HITACHI

• Engine Code: Z 12 XEP
• Vehicle Identification Number (VIN) from: 16079020
• Vehicle Identification Number (VIN) to: 56999999
• Fitting Position: Upper, Front, before catalytic converter
• Production Number: BWIdent
• Cable Length [mm]: 570
• Conductor Number: 4
• Available as universal article as well, see article no.: 1.998.235
• Number of circuits: 4
• Name: LAMBDA ANDUR
• Manufacturer: EPS

Oxygen Sensor: Regulating Sensor, Heated, Planar Sensor, Thread pre-greased

• Vehicle Identification Number (VIN) to: 63000001
• Exhaust System: for pre-catalytic converter
• Thread Size: M18x1.5
• Cable Length [mm]: 575
• Number of pins: 4
• Manufacturer Restriction: DENSO
• for OE number: 855429
• Quality: OE
• Weight [g]: 86
• Gross Weight [g]: 119
• Manufacturer: DENSO
• Name: DN DOX-2003
• Quality class: Q

Oxygen Sensor: Regulating Sensor, Heated, Planar Sensor, Thread pre-greased, Switching-type Oxygen Sensor Additional information: "Tootja: DENSO
CORSA C (F08, F68),
(kvaliteediklass: Q)" Lisainfo: "Tootja: DENSO
CORSA C (F08, F68),
(kvaliteediklass: Q)"

• Oxygen Sensor: Regulating Sensor
• Fitting Position: before catalytic converter
• Number of circuits: 4
• Overall Length [mm]: 549
• Available as universal article as well, see article no.: 0258986602
• Recommended change interval [km]: 250,000
• Name: LAMBDA ANDUR
• Manufacturer: BOS

• Vehicle Identification Number (VIN) to: 63000001
• Oxygen Sensor: Regulating Sensor, Thread pre-greased
• Exhaust System: for pre-catalytic converter
• Line insulation design: with silicone-coated woven-fibre insulation
• for OE number: 08 55 355
• Length [mm]: 570
• Number of circuits: 4
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Oxygen Sensor: Regulating Sensor
• Fitting Position: before catalytic converter
• Length [mm]: 570
• Technical Information Number: Universal 77015
• Manufacturer: FAE

• Oxygen Sensor: Diagnostic Probe
• Fitting Position: after catalytic converter
• Number of circuits: 4
• Overall Length [mm]: 300
• Available as universal article as well, see article no.: 0258986602
• Recommended change interval [km]: 250,000
• Name: LAMBDA ANDUR
• Manufacturer: BOS

• Transmission Type: Manual Transmission
• Oxygen Sensor: Regulating Sensor, Diagnostic Probe
• Block Separation:
• Length [mm]: 575
• Number of circuits: 4
• Manufacturer: VDO

Fitting Position: before catalytic converter, after catalytic converter

• Oxygen Sensor: Diagnostic Probe
• Length [mm]: 350
• Technical Information Number: Universal 77015
• Manufacturer: FAE

• Vehicle Identification Number (VIN) from: 63000001
• Exhaust System: for pre-catalytic converter
• Thread Size: M18x1.5
• Cable Length [mm]: 400
• Number of pins: 4
• Manufacturer Restriction: DENSO
• for OE number: 93186115
• Quality: OE
• Weight [g]: 83
• Gross Weight [g]: 116
• Manufacturer: DENSO
• Name: Lambda sensor
• Quality class: Q

Oxygen Sensor: Regulating Sensor, Heated, Planar Sensor, Thread pre-greased, Switching-type Oxygen Sensor Additional information: "Tootja: DENSO
CORSA D, 07.06-
(kvaliteediklass: Q)" Lisainfo: "Tootja: DENSO
CORSA D, 07.06-
(kvaliteediklass: Q)"

• Vehicle Identification Number (VIN) from: 16079020
• Vehicle Identification Number (VIN) to: 56999999
• Number of pins: 4
• Cable Length [mm]: 570
• Thread Size: M18x1,5
• Switch Pressure [bar]: 4
• Connector Shape: oval
• Manufacturer: VALEO

Oxygen Sensor: Regulating Sensor, Planar Sensor, Thread pre-greased, Heated Fitting Position: before catalytic converter, after catalytic converter

• Vehicle Identification Number (VIN) from: 66000001
• Vehicle Identification Number (VIN) to: 16079019
• Number of pins: 4
• Cable Length [mm]: 300
• Thread Size: M18x1,5
• Switch Pressure [bar]: 4
• Connector Shape: oval
• Manufacturer: VALEO

Oxygen Sensor: Regulating Sensor, Diagnostic Probe, Planar Sensor, Thread pre-greased, Heated Fitting Position: before catalytic converter, after catalytic converter

• Fitting Position: Front, Lower, before catalytic converter
• Oxygen Sensor: Regulating Sensor, Planar Sensor, Heated
• Cable Length [mm]: 325
• Name: DE ES21083-12B1
• Manufacturer: DELPHI

• Engine Code: Z 12 XEP
• Fitting Position: before catalytic converter
• Vehicle Identification Number (VIN) to: 53999999, 54999999, 56999999
• Oxygen Sensor: Heated
• Voltage [V]: 12
• Conductor Number: 4
• Cable Length [mm]: 570
• Number of pins: 4
• Manufacturer: PIERBURG