• Vehicle Equipment: for vehicles without air conditioning
• Country Specific Design: Japan
• not for country specific design: Japan
• Number of pins: 1
• Lisainfo: Temperature sensor for cooling system, 1 pin
• Additional information: Temperature sensor for cooling system, 1 pin

• Construction Year to: 12.1995
• Vehicle Equipment: for vehicles with air conditioning
• Number of pins: 2
• Colour: blue
• Manufacturer: JP GROUP A/S
• Lisainfo: Temperature sensor for cooling system, 2 pins
• Additional information: Temperature sensor for cooling system, 2 pins

• Connector Shape: oval
• Supplementary Article/Info 2: without cable
• Colour: black
• Lisainfo: Sender for outer temperature
• Additional information: Sender for outer temperature

• Length [mm]: 36
• Spanner Size: 13
• Housing Colour: black
• Manufacturer: KAMOKA

• Length [mm]: 50
• Spanner Size: 19
• Housing Colour: blue
• Manufacturer: KAMOKA

• Thread Size: 1/8x27 NPTF
• Manufacturer: FAE

• Spanner Size: 13
• Material: Brass
• Number of pins: 1
• Thread Size: M10x1
• Diameter [mm]: 8
• Length [mm]: 37
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: MAX

• Thread Size: 1/8x27 NPTF
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: VER

• Engine Code: C 20 XE
• Thread Size: 1/8-27NPT
• Spanner Size: 13
• for article number: 7.8288, 7.8343, 7.8344, 7.8346, 7.8348
• Manufacturer: FACET

Manufacturer: FAST

• Engine Code: C 20 XE
• Vehicle Equipment: for vehicles with air conditioning
• Number of pins: 2
• Manufacturer: KAVO PARTS

• Construction Year to: 12.1995
• Manufacturer: AIC

General Information: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.

• Engine Code: C 20 XE
• Thread Size: 1/8-27NPT
• Spanner Size: 13
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: EPS

for article number: 1.880.288, 1.880.343, 1.880.344, 1.880.346, 1.880.348

• Length [mm]: 37
• Outer Diameter [mm]: 8
• External Thread Size: M10 x 1
• Thread Length [mm]: 9.7
• Spanner Size: 13
• Number of connectors: 1
• Material: Brass
• Switch Point [°C]: 120
• Weight [kg]: 0.014
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: FEB

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Vehicle Equipment: for vehicles with air conditioning
• Connector Shape: rectangular
• Colour Coding: blue
• Thread Size: M 12
• Thread Pitch [mm]: 1.5
• Number of pins: 2
• Switch Point [°C]: 140
• Sensor Type: NTC Sensor
• Supplementary Article/Info 2: with seal ring
• Manufacturer: TOPRAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Engine Code: C 20 XE
• Number of pins: 1
• Thread Size: 1/8x27NPT
• Weight [kg]: 0.021
• Manufacturer: VEMO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Thread Size: M12x1.5
• Spanner Size: 19
• Manufacturer: FAST

• Length [mm]: 36.7
• Outer Diameter [mm]: 8
• External Thread Size: M10 x 1
• Thread Length [mm]: 9.7
• Spanner Size: 13
• Number of connectors: 1
• Material: Brass
• Switch Point [°C]: 120
• Weight [kg]: 0.014
• Name: SW 40 23 0003
• Manufacturer: SWAG

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Vehicle Identification Number (VIN) from: W8033698, W2087379, W7012363, W4035874, W5027386
• Manufacturer: DELLO AUTOMEGA

• not for country specific design: Japan
• Block Separation:
• Country Specific Design: Japan
• Spanner Size: 19
• Colour: blue
• Number of pins: 2
• Thread Size: M12x1,5
• Length [mm]: 51
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: MAX
• Lisainfo: 21-0124
• Additional information: 21-0124

Vehicle Equipment: for vehicles with air conditioning, for vehicles without air conditioning

• Vehicle Equipment: for vehicles with check control system
• Number of pins: 2
• Connector Shape: oval
• for OE number: 90346055
• Manufacturer: DELLO AUTOMEGA

• Number of pins: 2
• Connector Shape: oval
• Fabrication Number: ECT-PL-000
• Manufacturer: NTY

• Vehicle Identification Number (VIN) from: P2500001, P3000001, P5000001, P6000001, P8100001
• Number of pins: 2
• Name: ANDUR,VŽLISTEMPERATUUR
• Manufacturer: MAX
• Lisainfo: 21-0340
• Additional information: 21-0340

• Sensor Type: NTC Sensor
• Mounting Type: Bolted
• Connector Shape: rectangular
• Number of pins: 2
• Spanner Size: 19
• Thread Size: M12x1.5
• for OE number: 195321101000
• Supplementary Article/Info 2: with seal ring
• Name: Andur,Jahutusvedeliku temp.
• Manufacturer: NRF

• Vehicle Identification Number (VIN) from: P2500001, P3000001, P5000001, P6000001, P8100001
• Guarantee: 3 years guarantee
• Weight [kg]: 0.01
• Number of pins: 2
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY
• Name: CE 17SKV701

• Engine Code: C 20 XE
• Vehicle Equipment: for vehicles with air conditioning
• Number of pins: 2
• Height [mm]: 51.8
• Weight [kg]: 0.029
• Supplementary Article/Info 2: with seal ring
• Thread Size: M12x1,5
• Housing Colour: blue
• Spanner Size: 19
• Supplementary Article/Supplementary Info: with gasket/seal
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Number of pins: 2
• Colour: blue
• Manufacturer: AIC

General Information: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.

• Construction Year to: 12.1995
• Mounting Type: Bolted
• Voltage [V]: 12
• Resistor [Ohm]: 1,014, 146
• Temperature range from [°C]: 25
• Temperature range to [°C]: 80
• Thread Size: 1/8-27 NPT
• Sensor Type: NTC Sensor
• Number of pins: 1
• Housing Colour: black
• Number of mounting bores at thermostat housing: 1
• Assy./disassy. by qualified personnel required!:
• Name: HE 6PT009107161
• Manufacturer: HELLA

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Construction Year to: 12.1995
• Vehicle Equipment: for vehicles with air conditioning
• Colour: blue
• Manufacturer Restriction: für BOSCH
• Supplementary Article/Supplementary Info: with gasket/seal
• Temperature range [°C]: 25, 80
• Power [W]: 0.06
• Manufacturer: METZGER

• Vehicle Equipment: for vehicles with air conditioning
• not for country specific design: Japan
• Block Separation:
• Country Specific Design: Japan
• Thread Size: M12 x 1,5
• Spanner Size: 19
• Number of pins: 2
• Connector Shape: rectangular
• Manufacturer: ERA

• for OE number: 93232413
• Cable Length [mm]: 970
• Sensor Type: Passive sensor
• Manufacturer: KAMOKA

• Engine Code: C 20 XE
• Vehicle Equipment: for vehicles with air conditioning
• Sensor Type: NTC Sensor
• Thread Size: M12x1,5
• Spanner Size: 19
• Colour: blue
• Number of pins: 2
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: MEY

• Fabrication Number: ECP-PL-003
• Manufacturer: NTY

• Engine Code: C 20 XE
• Vehicle Equipment: for vehicles with air conditioning
• Thread Size: M12x1,5
• Spanner Size: 19
• for article number: 7.8113, 7.8114, 7.8149, 7.8151
• Manufacturer: FACET

• not for country specific design: Japan
• Block Separation:
• Country Specific Design: Japan
• Length [mm]: 51
• External Thread Size: M12 x 1,5
• Thread Length [mm]: 11
• Spanner Size: 19
• Number of connectors: 2
• Colour Coding: blue
• Switch Point [°C]: 20
• Weight [kg]: 0.022
• Supplementary Article/Info 2: with seal ring
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: FEB

Vehicle Equipment: for vehicles with air conditioning, for vehicles without air conditioning General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Sensor Type: NTC Sensor
• Mounting Type: Bolted
• Connector Shape: rectangular
• Number of pins: 2
• Socket colour: black
• Spanner Size: 19
• Thread Size: M12x1.5
• for OE number: 195051110100
• Supplementary Article/Info 2: with seal ring
• Name: Andur,Jahutusvedeliku temp.
• Manufacturer: NRF

• Engine Code: C 20 XE
• Vehicle Equipment: for vehicles with air conditioning
• Thread Size: M12x1,5
• Spanner Size: 19
• for article number: 1.880.113, 1.880.114, 1.880.149, 1.880.151
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: EPS

• Vehicle Equipment: for vehicles with check control system
• Number of pins: 2
• Lisainfo: Water level sensor for washertank
• Additional information: Water level sensor for washertank

• Number of pins: 2
• Connector Shape: oval
• Colour: black
• Mounting Type: Pressed
• for OE number: 9152245
• Manufacturer: MEAT&DORIA

• Number of connectors: 2
• Weight [kg]: 0.01
• Name: ANDUR,VŽLISTEMPERATUUR
• Manufacturer: FEB

Vehicle Identification Number (VIN) from: *********P2500001, *********P3000001, *********P5000001, *********P6000001, *********P8100001 General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• not for country specific design: Japan
• Block Separation:
• Country Specific Design: Japan
• Length [mm]: 50.7
• External Thread Size: M12 x 1,5
• Thread Length [mm]: 11
• Spanner Size: 19
• Number of connectors: 2
• Colour: blue
• Colour Coding: blue
• Switch Point [°C]: 20
• Weight [kg]: 0.022
• Supplementary Article/Info 2: with seal ring
• Name: SW 40 91 7695
• Manufacturer: SWAG
• Lisainfo: 40 91 7695 SWA
• Additional information: 40 91 7695 SWA

Vehicle Equipment: for vehicles with air conditioning, for vehicles without air conditioning General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Engine Code: C 20 XE
• Vehicle Equipment: for vehicles with air conditioning
• Mounting Type: Bolted
• Voltage [V]: 12
• Resistor [Ohm]: 2,080, 302
• Supplementary Article/Supplementary Info: with gasket/seal
• Temperature range from [°C]: 25
• Temperature range to [°C]: 80
• Thread Size: M12x1,5
• Colour: blue
• Spanner Size: 19
• Sensor Type: NTC Sensor
• Number of pins: 2
• Corresponds to the original part in colour: blue
• Manufacturer Restriction: Bosch
• Assy./disassy. by qualified personnel required!:
• Manufacturer: HELLA

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Number of connectors: 2
• Weight [kg]: 0.01
• Name: SW 99 90 1840
• Manufacturer: SWAG

Vehicle Identification Number (VIN) from: *********P2500001, *********P3000001, *********P5000001, *********P6000001, *********P8100001 General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Number of pins: 2
• Housing Colour: black
• Manufacturer: FAE

• Engine Code: C 20 XE
• Vehicle Equipment: for vehicles without air conditioning
• Thread Size: M12x1,5
• Spanner Size: 19
• for article number: 7.8149, 7.8151
• Manufacturer: FACET

• Number of pins: 3
• Sensor Type: Inductive Sensor
• Voltage [V]: 12
• Manufacturer: ABAKUS

General Information: The following information is for general and informational purposes only and does not constitute warranty terms. Warranty terms and conditions are available from our dealers and in our general terms and conditions of sale. Abakus spare/repair parts are intended only for vehicle repairs in order to restore their original functionality. Abakus spare/repair parts are used or sold to users only for the purpose of repairing vehicles to restore their original look and functionality and are not original/genuine/OE/OEM/OES replacement parts. These items do not originate from the vehicle manufacturer and may be the subject of a design not owned by Abakus and the manufacturer of this spare part. They may only be used for repairs to restore the intended vehicle to its original appearance. Our products are delivered without instruction of installation. Installation of our product may only be carried out by trained specialist technicians in specific car repairs. Products supplied by us are exclusively intended for proper and appropriate use. The warranty may become invalid in the event of: improper installation or repair, unsuitable application or use, installation or repair made outside specialist car workshops. Warranty claims are lost if the vehicle is modified and used for motor sports, tuning or similar events (except our tuning parts which are described in TecDoc and on our price list). Warranty application should include complete documentation among others: chassis no., first registration, vehicle mileage, information about LPG installation, fault memory log, pictures, our QC (quality check) code, installation invoice, contact details of the car repair workshop performing the replacement or repair. Warranty application are available in our Client Panel system. Complaints may require supplementing data such as error memory logs. Incomplete documentation may result in rejection of the claim. Any damage caused during transport is not considered quality damage and will be considered on an individual basis. The product is intended for use within the performance limits specified by the manufacturer and should only be used by qualified personnel who have been trained to operate this product. Before each use, the product should be checked for damage or fixing of its parts and not used if any defects or loose parts are found. Failure to follow the manufacturer's guidelines could result in potential product damage or even injury. Wear appropriate protective clothing if necessary when working with the product.

• Engine Code: C 20 XE
• Vehicle Equipment: for vehicles without air conditioning
• Thread Size: M12x1,5
• Spanner Size: 19
• for article number: 1.880.149, 1.880.151
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: EPS

• Engine Code: C 20 XE
• Colour: black
• Number of pins: 2
• Manufacturer: VDO

Manufacturer: NRF

• Voltage [V]: 12
• Length [mm]: 950
• Number of pins: 3
• Guarantee: 3 years guarantee
• Weight [kg]: 0.12
• Operating Mode: Electric
• Always compare old and new part (in particular OE No.):
• Name: CE 17SKV225
• Manufacturer: ESEN SKV

• Voltage [V]: 12
• Temperature range to [°C]: 250
• Resistor [Ohm]: 5,000
• Number of pins: 2
• Corresponds to the original part in colour: black
• Plug Type: Blade Terminal
• Connector Shape: oval
• Assy./disassy. by qualified personnel required!:
• Manufacturer: HELLA
• Name: HE 6PT009104011

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Connector Shape: rectangular
• Number of pins: 3
• Supplementary Article/Info 2: with cable
• Manufacturer: TOPRAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Vehicle Equipment: for vehicles with check control system
• Weight [kg]: 0.016
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Vehicle Equipment: for vehicles without air conditioning
• not for country specific design: Japan
• Thread Size: M12 x 1,5
• Spanner Size: 19
• Number of pins: 2
• Manufacturer: ERA

• for OE number: 93232413
• Cable Length [mm]: 920
• Sensor Type: Inductive Sensor
• Number of pins: 3
• Supplementary Article/Info 2: with seal ring
• Assy./disassy. by qualified personnel required!:
• Name: HE 6PU013122921
• Manufacturer: HELLA

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Vehicle Equipment: for vehicles with air conditioning
• Number of pins: 2
• Thread Size: M12x1.5
• Supplementary Article/Supplementary Info: with gasket/seal
• Net Weight [g]: 25
• Packaging width [cm]: 6.7
• Packaging length [cm]: 8.7
• Packaging height [cm]: 9.2
• Name: MH TSE12
• Manufacturer: MAHLE

• Number of pins: 2
• Thread Size: M12x1,5
• Colour: black
• Weight [kg]: 0.032
• Manufacturer: VEMO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Model Year to: 1993
• Sensor Type: Inductive Sensor
• Supplementary Article/Info 2: with seal ring, with protection hose
• Cable Length [mm]: 970
• Number of pins: 3
• Name: ANDUR, VŽNTVOLL
• Manufacturer: MEY

• Engine Code: C 20 XE
• Cable Length [mm]: 925
• Number of pins: 3
• Name: ANDUR, VŽNTVOLL
• Manufacturer: DLP

Vehicle Identification Number (VIN) from: S2000001/S3000001, S4000001/S5000001, S6000001/S8000001, SA/SB000001/SE/SP, SS

• Number of pins: 2
• Thread Size: M12x1,5
• Housing Colour: black
• Colour: black
• Manufacturer: METZGER

• Sensor Type: Inductive Sensor
• Supplementary Article/Info 2: with seal ring
• Cable Length [mm]: 975
• Number of pins: 3
• Name: ANDUR, VŽNTVOLL
• Manufacturer: MEY

• Length [mm]: 1,015
• Weight [kg]: 0.106
• Required quantity: 1
• Resistor [Ohm]: 550
• Colour: black
• Operating Mode: Electric
• Cable Length [mm]: 940
• Sensor Type: Passive sensor, Inductive Sensor
• Number of pins: 3
• Number of connectors: 3
• Rated Voltage [V]: 12
• Fitting Depth [mm]: 24
• Supplementary Article/Info 2: with seal ring, with cable
• Connector Shape: rectangular
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Number of pins: 3
• Manufacturer: AIC

General Information: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.

• Resistor [Ohm]: 550
• Cable Length [mm]: 970
• Number of pins: 3
• Fitting Depth [mm]: 24
• Weight [kg]: 0.1
• Operating Mode: Electric
• Manufacturer: ERA

• Construction Year from: 07.1994
• Sensor Type: Inductive Sensor
• Number of pins: 3
• Voltage [V]: 12
• Connector Shape: angled
• Supplementary Article/Info 2: with cable
• Resistor [Ohm]: 550
• Manufacturer: VALEO
• Name: VA 254028

• Transmission ID: AF20
• Number of pins: 2
• Connector Shape: oval
• Supplementary Article/Info 2: without cable
• Sensor Type: Inductive Sensor
• Fitting Depth [mm]: 28
• Vehicle Equipment: for vehicles with automatic transmission
• Fitting Position: Inlet
• for OE number: 1238113
• Manufacturer: MEAT&DORIA

• Length [mm]: 1,000
• Number of connectors: 3
• Cable Length [mm]: 920
• Weight [kg]: 0.12
• Supplementary Article/Info 2: with seal ring
• Manufacturer: FEBI

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Engine Code: C 20 XE
• Length [mm]: 990
• Manufacturer: FACET

• Engine Code: C 20 XE
• Number of pins: 3
• Supplementary Article/Info 2: with cable
• Connector Shape: rectangular
• Manufacturer: FAE

• Engine Code: C 20 XE
• Length [mm]: 990
• Name: EP 1.953.073
• Manufacturer: EPS

Manufacturer: MAGNETI MARELLI

• Voltage [V]: 12
• Resistor [Ohm]: 500
• Tolerance [%]: 10
• Cable Length [mm]: 990
• Sensor Type: Inductive Sensor
• Number of pins: 3
• Assy./disassy. by qualified personnel required!:
• Manufacturer: HELLA

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Sensor Type: NTC Sensor
• Mounting Type: Bolted
• Connector Shape: round
• Number of pins: 1
• Spanner Size: 12
• Thread Size: 1/8 NPT
• for OE number: 3439088