• Number of pins: 2
• Connector Shape: oval
• Socket colour: green
• Thread Size: M12x1,5
• Sensor Type: NTC Sensor
• Spanner Size: 19 mm
• for OE number: 8942220010
• Manufacturer: MEAT&DORIA

• for OE number: 89424-87703-000
• Colour: black
• Sensor Type: NTC Sensor
• Number of pins: 2
• Connector Shape: oval
• Fabrication Number: ECT-MZ-000
• Manufacturer: NTY
• Name: NTY ECT-MZ-000

• Engine Code: RF7J
• Fitting Position: Upper
• Number of pins: 2
• Manufacturer: KAVO

• Engine Code: RF7J
• Manufacturer Restriction: DENSO
• Thread Size: M12x1,5
• Spanner Size: 19
• Corresponds to the original part in colour: green
• for article number: 1.880.606, 1.880.732, 1.880.733
• Name: EP 1.830.177
• Manufacturer: EPS

• Engine Code: RF7J
• Manufacturer Restriction: DENSO
• Thread Size: M12x1,5
• Spanner Size: 19
• Corresponds to the original part in colour: green
• for article number: 7.8606, 7.8732, 7.8733
• Manufacturer: FACET

• Engine Code: RF7J
• Manufacturer Restriction: DENSO
• Number of connectors: 2
• Number of pins: 2
• Supplementary Article/Info 2: with seal ring
• Housing Colour: green
• Supplementary Article/Supplementary Info: with gasket/seal
• Thread Size: M12x1,5
• Manufacturer: VIEROL

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Length [mm]: 79
• Thread Size: M10 x 1,25
• Cable Length [mm]: 440
• Number of pins: 1
• Supplementary Article/Info 2: with cable
• Fabrication Number: ESS-MZ-001
• Manufacturer: NTY
• Name: NTY ESS-MZ-001

• Housing Colour: green
• Number of pins: 2
• Thread Size: M 12x1,5
• Manufacturer: FAE

Manufacturer: MAGNETI MARELLI

• Number of pins: 2
• Connector Shape: oval
• Colour: black
• Sensor Type: NTC Sensor
• for OE number: BP4W18845
• Manufacturer: MEAT & DORIA

• Manufacturer: FAE
• Additional information: 33235 NRF
• Lisainfo: 33235 NRF

• Engine Code: RF7J
• Fitting Position: Upper
• Supplementary Article/Info 2: without fastening clamp
• Name: EP 1.994.010
• Manufacturer: EPS

• Engine Code: RF7J
• Fitting Position: Upper
• Supplementary Article/Info 2: without fastening clamp
• Manufacturer: FACET

• Engine Code: RF7J
• Number of pins: 2
• Manufacturer: JPN

• Fabrication Number: ECD-MZ-001
• Manufacturer: NTY
• Name: NTY ECD-MZ-001

• Housing Type: without housing
• Fabrication Number: EPP-MZ-001
• Manufacturer: NTY
• Name: NTY EPP-MZ-001

• Fabrication Number: ECM-MZ-003
• Manufacturer: NTY

• Number of pins: 5
• Connector Shape: rectangular
• Assy./disassy. by qualified personnel required!:
• Name: AB 120-08-085
• Manufacturer: ABAKUS

General Information: The following information is for general and informational purposes only and does not constitute warranty terms. Warranty terms and conditions are available from our dealers and in our general terms and conditions of sale. Abakus spare/repair parts are intended only for vehicle repairs in order to restore their original functionality. Abakus spare/repair parts are used or sold to users only for the purpose of repairing vehicles to restore their original look and functionality and are not original/genuine/OE/OEM/OES replacement parts. These items do not originate from the vehicle manufacturer and may be the subject of a design not owned by Abakus and the manufacturer of this spare part. They may only be used for repairs to restore the intended vehicle to its original appearance. Our products are delivered without instruction of installation. Installation of our product may only be carried out by trained specialist technicians in specific car repairs. Products supplied by us are exclusively intended for proper and appropriate use. The warranty may become invalid in the event of: improper installation or repair, unsuitable application or use, installation or repair made outside specialist car workshops. Warranty claims are lost if the vehicle is modified and used for motor sports, tuning or similar events (except our tuning parts which are described in TecDoc and on our price list). Warranty application should include complete documentation among others: chassis no., first registration, vehicle mileage, information about LPG installation, fault memory log, pictures, our QC (quality check) code, installation invoice, contact details of the car repair workshop performing the replacement or repair. Warranty application are available in our Client Panel system. Complaints may require supplementing data such as error memory logs. Incomplete documentation may result in rejection of the claim. Any damage caused during transport is not considered quality damage and will be considered on an individual basis. The product is intended for use within the performance limits specified by the manufacturer and should only be used by qualified personnel who have been trained to operate this product. Before each use, the product should be checked for damage or fixing of its parts and not used if any defects or loose parts are found. Failure to follow the manufacturer's guidelines could result in potential product damage or even injury. Wear appropriate protective clothing if necessary when working with the product.

• Number of pins: 3
• Connector Shape: oval
• Guarantee: 3 years guarantee
• Number of mounting bores: 2
• Weight [kg]: 0.03
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY

• Number of pins: 5
• Quality class: PJ
• Name: Air flow sensor

• Number of pins: 1
• Manufacturer: AIC

General Information: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.

• Number of pins: 5
• Assy./disassy. by qualified personnel required!:
• Manufacturer: ABAKUS LORO

General Information: The following information is for general and informational purposes only and does not constitute warranty terms. Warranty terms and conditions are available from our dealers and in our general terms and conditions of sale. Abakus spare/repair parts are intended only for vehicle repairs in order to restore their original functionality. Abakus spare/repair parts are used or sold to users only for the purpose of repairing vehicles to restore their original look and functionality and are not original/genuine/OE/OEM/OES replacement parts. These items do not originate from the vehicle manufacturer and may be the subject of a design not owned by Abakus and the manufacturer of this spare part. They may only be used for repairs to restore the intended vehicle to its original appearance. Our products are delivered without instruction of installation. Installation of our product may only be carried out by trained specialist technicians in specific car repairs. Products supplied by us are exclusively intended for proper and appropriate use. The warranty may become invalid in the event of: improper installation or repair, unsuitable application or use, installation or repair made outside specialist car workshops. Warranty claims are lost if the vehicle is modified and used for motor sports, tuning or similar events (except our tuning parts which are described in TecDoc and on our price list). Warranty application should include complete documentation among others: chassis no., first registration, vehicle mileage, information about LPG installation, fault memory log, pictures, our QC (quality check) code, installation invoice, contact details of the car repair workshop performing the replacement or repair. Warranty application are available in our Client Panel system. Complaints may require supplementing data such as error memory logs. Incomplete documentation may result in rejection of the claim. Any damage caused during transport is not considered quality damage and will be considered on an individual basis. The product is intended for use within the performance limits specified by the manufacturer and should only be used by qualified personnel who have been trained to operate this product. Before each use, the product should be checked for damage or fixing of its parts and not used if any defects or loose parts are found. Failure to follow the manufacturer's guidelines could result in potential product damage or even injury. Wear appropriate protective clothing if necessary when working with the product.

• Fitting Position: Lower
• Thread Size: M 10x1.25
• Number of pins: 2
• Housing Colour: blue
• Manufacturer: FAE

• Number of connectors: 2
• Weight [kg]: 0.018
• Manufacturer: FEBI BILSTEIN

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Number of pins: 5
• Housing Type: without housing
• Lisainfo: Air Mass Sensor
• Additional information: Air Mass Sensor

• Engine Code: RF7J
• Pressure from [kPA]: 27
• Pressure to [kPA]: 400
• Output Voltage, from [V]: 0.25
• Output Voltage, up to [V]: 4.51
• Name: EP 1.993.198
• Manufacturer: EPS
• Additional information: 1-993-198
• Lisainfo: 1-993-198

• Engine Code: RF7J
• Pressure from [kPA]: 27
• Pressure to [kPA]: 400
• Output Voltage, from [V]: 0.25
• Output Voltage, up to [V]: 4.51
• Manufacturer: FACET

• Number of pins: 5
• Recommended additional repairs: Air Filter
• Used part return not required:
• Fitting Position: Air Filter Housing
• New Part:
• Manufacturer: TOPRAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Voltage [V]: 12
• Number of pins: 5
• Guarantee: 3 years guarantee
• New Part:
• Used part return not required:
• Weight [kg]: 0.07
• Operating Mode: Electric
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY
• Name: CE 07SKV102

• Voltage [V]: 12
• Number of pins: 5
• Guarantee: 3 years guarantee
• New Part:
• Used part return not required:
• Weight [kg]: 0.11
• Operating Mode: Electric
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY
• Name: CE 07SKV107

• Voltage [V]: 12
• Number of pins: 5
• Guarantee: 3 years guarantee
• New Part:
• Used part return not required:
• Weight [kg]: 0.11
• Operating Mode: Electric
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY
• Name: CE 07SKV151

• Number of pins: 5
• Manufacturer: JPN

• Housing Type: without housing
• Number of pins: 5
• Manufacturer: VDO

• Required quantity: 1
• Voltage [V]: 12
• Number of pins: 5
• Housing Type: without housing
• Manufacturer: BREMI

Manufacturer: JAPKO

• Engine Code: RF7J
• Housing Type: without housing
• Name: EP 1.991.163
• Manufacturer: EPS

• for OE number: 1380084E00000
• Manufacturer: MEAT&DORIA

• Engine Code: RF7J
• Housing Type: without housing
• Manufacturer: FACET

• Colour: black
• Number of pins: 3
• Pressure to [kPA]: 401
• Manufacturer: FAE

• Oxygen Sensor: Regulating Sensor
• Fitting Position: Front
• Quantity: 1
• Number of connectors: 5
• Manufacturer: VERNET

• Number of pins: 5
• Supplementary Article/Info 2: with seal ring
• Number of Holes: 2
• Manufacturer: ERA

• alternatively:
• Required quantity: 1
• Voltage [V]: 12
• Number of pins: 5
• Housing Type: without housing
• Manufacturer: BREMI

• Engine Code: RF7J
• Operating Mode: Electric
• Voltage [V]: 12
• Manufacturer: PIERBURG

• Mounting Type: Bolted
• Number of pins: 5
• Housing Colour: black
• Plug Type: Male
• Assy./disassy. by qualified personnel required!:
• Manufacturer: HELLA
• Name: HE 8ET009142891

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Engine Code: RF7J
• Cable Length [mm]: 440
• Number of pins: 1
• Fitting Depth [mm]: 12
• Manufacturer: ERA

• Housing Type: without housing
• Number of pins: 5
• Plug Type: Male
• Housing Colour: black
• Voltage [V]: 12
• Recommended additional repairs: Air Filter
• Manufacturer: DELPHI
• Name: DE AF10135-12B1

• Number of pins: 3
• Manufacturer: METZGER

• Engine Code: MZR-CD20/F
• for OE number: 1 701 766
• Connector Shape: D Shape
• Number of pins: 6
• Socket colour: black
• Thread Size: M18 x 1,5
• Number of circuits: 5
• Conductor Number: 5
• Length [mm]: 270
• Overall Length [mm]: 410
• Fitting Position: before catalytic converter
• Cable Length [mm]: 270
• Oxygen Sensor: Regulating Sensor, Thread pre-greased
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Number of pins: 5
• for OE number: 22204-21010
• Quality: OE
• Operating Mode: Electric
• Gross Weight [g]: 79
• alternative item: -
• Manufacturer: DENSO
• Name: DN DMA-0113

Additional information: "Tootja: DENSO
HILUX SAMOCHÓD TEREN
(kvaliteediklass: Q)" Lisainfo: "Tootja: DENSO
HILUX SAMOCHÓD TEREN
(kvaliteediklass: Q)"

• Oxygen Sensor: Diagnostic Probe
• Fitting Position: after catalytic converter
• Construction Year to: 12.2009
• for OE number: RF8G188G1B
• Pikkus (mm): 1 000
• Pistikkontaktide arv: 4
• Manufacturer: FAE

• Operating Mode: Electric
• Manufacturer: MAGNETI MARELLI

• Height [mm]: 12
• Number of connectors: 1
• Manufacturer: VEMO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Number of pins: 3
• Colour: black
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Oxygen Sensor: Broadband Oxygen Sensor
• Number of pins: 5
• Cable Length [mm]: 410
• Quality: OE EQUIVALENT
• for OE number: 5146168AA
• Manufacturer: MEAT & DORIA

• Engine Code: RF7J
• Operating Mode: Electric
• Voltage [V]: 12
• Manufacturer: PIERBURG

• Construction Year to: 12.2009
• Thread Size: M18x1.5
• Cable Length [mm]: 960
• Number of pins: 4
• Manufacturer Restriction: DENSO
• for OE number: RF8G188G1B
• Quality: OE
• Weight [g]: 143
• Gross Weight [g]: 176
• Manufacturer: DENSO
• Name: DN DOX-0539

Oxygen Sensor: Diagnostic Probe, Heated, Finger-type Sensor, Broadband Oxygen Sensor, Thread pre-greased Additional information: "Tootja: DENSO
(kvaliteediklass: Q)" Lisainfo: "Tootja: DENSO
(kvaliteediklass: Q)"

• Oxygen Sensor: Broadband Oxygen Sensor
• Number of pins: 5
• Cable Length [mm]: 410
• for OE number: 55204005
• Manufacturer: MEAT&DORIA