• Operating voltage [V]: 12
• Rated Power [W]: 480
• Rated current [A]: 40
• Combi Switch Function: Normally Open Contact
• Number of pins: 4
• Lisainfo: Relay, 12 Volt, 40 Amp
• Additional information: Relay, 12 Volt, 40 Amp

Relay function: Terminal 75, Interior Blower, Suction pipe pre-heating, Sunroof, Pump, fuel pre-supply, Start-stop system, Magnetic clutch, Surge protection, Battery main switch, Engine control unit, Normally open contact, X contact relief, Fan, engine cooling, Electric booster heater, Secondary Air System, Water pump after-run, Rear Window Wiper, heater/air conditioning, Clamp 15, Fuel Pump, Window Regulator, Heated windscreen, Heated rear window, Parking Heater

• Operating voltage [V]: 12
• Number of connectors: 3

Lisainfo: Relay for turn signal and emergency light, 12 Volt, 4x21 W Additional information: Relay for turn signal and emergency light, 12 Volt, 4x21 W

• Rated Voltage [V]: 12
• Rated current [A]: 30
• Supplementary Article/Supplementary Info: without holder
• Number of pins: 5
• Temperature range from [°C]: -40
• Temperature range to [°C]: 100
• Housing Type: Synthetic Material Housing
• General Information: Multifunctional relay
• Manufacturer: VIKA

Combi Switch Function: without light dimmer function, Normally Open Contact

• Number of connectors: 4
• Rated Voltage [V]: 12
• Rated current [A]: 40
• Temperature range from [°C]: -40
• Temperature range to [°C]: 85
• General Information: Multifunctional relay; 4 claws
• Manufacturer: VIKA

• Length [mm]: 30
• Width [mm]: 30
• Height [mm]: 30
• Vehicle Equipment: for vehicles without trailer hitch
• Number of pins: 3
• Name: OHUTULEDE RELEE
• Manufacturer: MAX
• Lisainfo: 103131DE5
• Additional information: 103131DE5

• Relay function: Starter
• Combi Switch Function: Normally Open Contact
• Height [mm]: 25
• Length [mm]: 28
• Width [mm]: 28
• Voltage [V]: 12
• Name: MITME FUNKTSIOONIGA RELEE
• Manufacturer: MAX

• Voltage [V]: 12
• Capacity at 12V: 30A/40A
• Combi Switch Function: Changeover Contact
• Number of pins: 5
• Quantity: 1
• Temperature range from [°C]: -40
• Temperature range to [°C]: +125
• Weight [g]: 24
• Inductive Load [A]: 15
• Capacitive Load [A]: 5
• Rated current [A]: 40
• Ohmic Load [A]: 40
• Assy./disassy. by qualified personnel required!:
• Manufacturer: HELLA
• Name: HE 4RD933332551

Relay function: Comfort Equipment Variant (trim package), Park Distance Control, ABS, Low Beam, High Beam, Heated rear window, ESP, Window Regulator, Starter, Klaxon, Air Conditioning, Light switch, Fan, heater/air conditioning, Interior Blower, Clamp 15, Daytime Running Light, Convertible Top Hydraulics, Central Locking, ABS recovery pump, Exterior Mirror Adjustment, Heatable exterior mirror, Electric booster heater, Interior Lighting, Clamp 15R, Clamp 87, Fuel Pump, Oxygen Sensor Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Operating voltage [V]: 12
• Rated current [A]: 40
• Combi Switch Function: Normally Open Contact
• Length [mm]: 28
• Width [mm]: 28
• Height [mm]: 25
• Connector type: 4x 6,3 mm
• Number of pins: 4
• Name: MITME FUNKTSIOONIGA RELEE
• Manufacturer: MEY

Relay function: Heated rear window, Washer Fluid Pump, headlight cleaning, Cigarette Lighter, Rear Fog Light, Seat Heating, Air Conditioning, Engine control unit, Secondary Air System, Fuel Pump, Pump, automatic transmission, ESP, Daytime Running Light, Alternator, Normally open contact, Rotating Beacon, Magnetic clutch, Fuel cooling, Radiator Fan Overrun, Alarm System, Window Regulator, Starter, Front Fog Light, Fan, engine cooling, Klaxon

• Relay function: Sunroof
• Combi Switch Function: Normally Open Contact
• Voltage [V]: 12
• Name: Mitme funktsiooniga relee
• Manufacturer: MAX

• Operating voltage [V]: 12
• Rated Power [W]: 480
• Rated current [A]: 40
• Combi Switch Function: Normally Open Contact
• Length [mm]: 28
• Width [mm]: 28
• Height [mm]: 25
• Connector type: 2x 6,3 mm, 2x 9,5 mm
• Number of pins: 4
• Name: MITME FUNKTSIOONIGA RELEE
• Manufacturer: MEY

Relay function: Fuel Pump, Engine control unit, Surge protection, Suction pipe pre-heating, Interior Blower, Heated rear window, Battery main switch, Heated windscreen, Fan, heater/air conditioning, Rear Window Wiper, Water pump after-run, Secondary Air System, Electric booster heater, engine cooling, Normally open contact, Clamp 15, Parking Heater, X contact relief, Window Regulator, Terminal 75, Sunroof, Pump, fuel pre-supply, Start-stop system, Magnetic clutch

• Number of pins: 4
• Voltage [V]: 12
• Current Strength [A]: 70
• Relay function: Normally open contact
• Manufacturer: AIC

General Information: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.

• Voltage [V]: 12
• Weight [kg]: 0.025
• Number of connectors: 4
• Current Strength [A]: 30
• Supplementary Article/Supplementary Info: with holder
• General Information: Multifunctional relay
• Manufacturer: BORSEHUNG

• Vehicle Equipment: for vehicles without trailer hitch
• Relay Number: 21, 191
• Voltage [V]: 12
• Rated Power [W]: 21
• Number of connectors: 3
• Colour: black
• Material: Plastic
• Operating Mode: Electronic
• Weight [kg]: 0.032
• Name: SUUNATULEDE LšLITI
• Manufacturer: FEB

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Voltage [V]: 12
• Number of pins: 6
• Name: RELEE,KOJAMEHED-PESU-INTERVALL
• Manufacturer: MAX

• Voltage [V]: 12
• Current Strength [A]: 70
• Number of pins: 7
• Lisainfo: Relay, glowing, 12 Volt, 70 Amp, economy version
• Additional information: Relay, glowing, 12 Volt, 70 Amp, economy version

• Operating voltage [V]: 12
• Rated Power [W]: 120
• Rated current [A]: 10
• Combi Switch Function: Normally Open Contact
• Length [mm]: 30
• Width [mm]: 30
• Height [mm]: 42
• Connector type: 1x 2,8 mm, 5x 6,3 mm
• Number of pins: 6
• Name: RELEE,KOJAMEHED-PESU-INTERVALL
• Manufacturer: MEY

• Üldine informatsioon: Hazard light relay
• Manufacturer: BORSEHUNG

• Voltage [V]: 12
• Switching Capacity [W]: 21
• Operating Mode: Electric
• Number of pins: 3
• Plug Type: Blade Terminal
• Mounting Type: Plugged
• Manufacturer: VEMO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Operating voltage [V]: 12
• Switching Capacity [W]: 4x21

• Vehicle Equipment: for vehicles with trailer hitch
• Relay Number: 22
• Voltage [V]: 12
• Number of connectors: 4
• Operating Mode: Electric
• Weight [kg]: 0.03
• Manufacturer: FEBI BILSTEIN

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Mounting Type: Plugged
• Operating Mode: Electronic
• Switching Capacity [W]: 2(4)x21W+0...5
• Number of pins: 3
• Voltage [V]: 12
• Registration Type: ECE approved
• Temperature range from [°C]: -40
• Temperature range to [°C]: +70
• Assy./disassy. by qualified personnel required!:
• Name: Suunatulede lliti
• Manufacturer: HEL

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Voltage [V]: 12
• Operating Mode: Electric
• Vehicle Equipment: for vehicles with trailer hitch
• Number of pins: 4
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Voltage [V]: 12
• Current Strength [A]: 70
• Number of pins: 7
• Manufacturer: JP GROUP
• Lisainfo: Relay, glowing, 12 Volt, 70 Amp, Germany
• Additional information: Relay, glowing, 12 Volt, 70 Amp, Germany

• Voltage [V]: 12
• Number of pins: 6
• Fitting Position: Engine Compartment
• Manufacturer: VEMO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Mounting Type: Plugged
• Operating Mode: Electronic
• Switching Capacity [W]: 2+1(6)x21W+5 EP
• Number of pins: 4
• Voltage [V]: 12
• Supplementary Article/Info 2: for trailer
• Supplementary Article/Supplementary Info: with holder
• Registration Type: ECE approved
• Temperature range from [°C]: -40
• Temperature range to [°C]: +85
• Assy./disassy. by qualified personnel required!:
• Name: Suunatulede lliti
• Manufacturer: HEL

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Engine Code: CY
• Guarantee: 5 years guarantee
• Operating voltage [V]: 12
• Manufacturer: HUCO
• Name: HU 132061

General Information: Recommendation: Use grease for glow plugs 134100 = 10g. or 134101 = 100g., see accessory lists.

• Voltage [V]: 12
• Number of connectors: 7
• Fitting Position: Engine Compartment
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Supplementary Article/Supplementary Info: without holder
• Voltage [V]: 12
• Temperature range from [°C]: -30
• Temperature range to [°C]: +85
• Number of pins: 6
• Assy./disassy. by qualified personnel required!:
• Name: HE 5WG003620097
• Manufacturer: HELLA

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Guarantee: 5 years guarantee
• Name: RELEE, HOOGSšSTEEM
• Manufacturer: HUC
• Additional information: 132062 HUCO
• Lisainfo: 132062 HUCO

General Information: Recommendation: Use grease for glow plugs 134100 = 10g. or 134101 = 100g., see accessory lists.

• Guarantee: 5 years guarantee
• Check OE number:
• Operating voltage [V]: 12
• Manufacturer: HUCO
• Name: HU 132063

General Information: Recommendation: Use grease for glow plugs 134100 = 10g. or 134101 = 100g., see accessory lists.

• Supplementary Article/Supplementary Info: without holder
• Voltage [V]: 12
• Temperature range from [°C]: -30
• Temperature range to [°C]: +85
• Number of pins: 6
• Assy./disassy. by qualified personnel required!:
• Name: HE 5WG003620091
• Manufacturer: HELLA

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Mounting Type: Plugged
• Operating Mode: Electronic
• Switching Capacity [W]: 2+1(6)x21W EP
• Number of pins: 5
• Voltage [V]: 12
• Supplementary Article/Info 2: for trailer
• Observe illustration:
• Registration Type: ECE approved
• Assy./disassy. by qualified personnel required!:
• SVHC: 7439-92-1; Lead
• Name: SUUNATULEDE LšLITI
• Manufacturer: HEL

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Voltage [V]: 12
• Current Strength [A]: 70
• Number of pins: 7
• Manufacturer: VEMO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.