• Supplementary Article/Supplementary Info: with seal
• Manufacturer: JP GROUP
• Lisainfo: Water pump
• Additional information: Water pump

• Number of pins (input) [-pin connector]: 3
• Number of pins (output) [-pin connector]: 2
• Plug Type: Female
• Vehicle Equipment: for vehicles with parking heater
• Number of circuits: 2
• Material: CuSn (copper-tin)
• Cable Length [mm]: 360
• Cable cross-section from [mm²]: 0.5
• Cable cross-section to [mm²]: 0.5
• Cable insulation material: Silicone
• Article number of recommended accessories: 2221059
• Manufacturer: METZGER

for OE number: 1K0965561, 1K0965561A, 1T0965561, 3C0965561, 7N0965561, 7N0965561A, 7N0965561B

• Transmission Type: 6-Speed Manual Transmission
• Fabrication Number: CPW-VW-051
• Manufacturer: NTY

• Engine Code: CAYC
• Number of Teeth: 19
• Water Pump Type: for timing belt drive
• for OE number: 03L 121 011
• Manufacturer: KAMOKA

• Manufacturer Restriction: VAG
• Plug Type ID: Code A
• Cable Length [mm]: 175
• Number of pins: 3
• Cable Cross Section [mm²]: 0.75
• Contact surface: Silver-plated
• Cable insulation material: Silicone
• Supplementary Article/Supplementary Info: with socket housing, with gaskets/seals
• Supplementary Article/Info 2: with pipe
• Temperature range from [°C]: -25
• Temperature range to [°C]: +140
• SVHC: No SVHC present!
• Name: Kaabli remondikomplekt, heitgaasi rohuandur
• Manufacturer: HBE

• Number of Teeth: 19
• Name: VEEPUMP
• Manufacturer: MAX

• reinforced version:
• Model Year from: 2009
• Packaging length [cm]: 11.2
• Packaging width [cm]: 11.2
• Packaging height [cm]: 11.2
• Weight [kg]: 0.68

• Service exchange part:
• Supplementary Article/Info 2: with evaporator
• reinforced version:
• Model Year from: 2009
• Manufacturer: DOLZ
• Name: DO A224

• Model Year to: 2012
• Number of Teeth: 19
• Water Pump Pulley Ø [mm]: 56
• Impeller Diameter [mm]: 64
• Number of blades/vanes: 7
• Operating Mode: Mechanical
• Water pump impeller material: Aluminium
• Supplementary Article/Supplementary Info: with seal
• Quality class: PJ
• Name: Water pump

• Number of Teeth: 19
• Operating Mode: Mechanical
• Supplementary Article/Info 2: with seal ring
• Number of blades/vanes: 7
• Water Pump Pulley Ø [mm]: 56.23
• Impeller Diameter [mm]: 64
• Water Pump Type: for timing belt drive
• Water pump impeller material: Metal
• Manufacturer: METELLI

• Water pump impeller material: Plastic
• Seal Material: Rubber
• Material: Cast Aluminium
• Number of Teeth: 19
• Number of blades/vanes: 8
• Weight [kg]: 0.725
• Supplementary Article/Supplementary Info: with seal
• Observe service information:
• Name: VEEPUMP
• Manufacturer: FEB

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Trim Level: TB
• for OE number: 03L121011PX
• Belt Pulley Ø [mm]: 56
• Height 1 [mm]: 28.5
• Weight [kg]: 1.1
• Name: DA DP206
• Manufacturer: DAYCO

• Engine Code: CAYC
• for OE number: 5N0965561A
• Operating Mode: Electric
• Voltage [V]: 12
• Name: Lisaveepump (jahutusvee ringlusssteem)
• Manufacturer: MAX

• Number of Teeth: 19
• Operating Mode: Mechanical
• Supplementary Article/Info 2: with seal ring
• Number of blades/vanes: 7
• Water Pump Pulley Ø [mm]: 56.23
• Impeller Diameter [mm]: 64
• Water Pump Type: for timing belt drive
• Water pump impeller material: Metal
• Name: VEEPUMP
• Manufacturer: GRA

• Supplementary Article/Supplementary Info: with seal
• Water Pump Type: for timing belt drive
• Number of Teeth: 19
• Quality: Sealed with SiC/SiC
• New part without deposit:
• Article number of the recommended special tool: 999 990 0002
• Name: VEEPUMP
• Manufacturer: MEY

General Information: MEYLE provides a 100,000-mile guarantee for all MEYLE water pumps and a 4-year warranty for MEYLE-HD water pumps. The 100,00 mile warranty requires the cooling system to be flushed before installation.

• Weight [kg]: 0.76
• Name: AI 1992
• Manufacturer: AIRTEX

• Voltage [V]: 12
• Operating Mode: Electric
• for OE number: 5N0965561
• Manufacturer: ABAKUS DEPO/LORO

General Information: The following information is for general and informational purposes only and does not constitute warranty terms. Warranty terms and conditions are available from our dealers and in our general terms and conditions of sale. Abakus spare/repair parts are intended only for vehicle repairs in order to restore their original functionality. Abakus spare/repair parts are used or sold to users only for the purpose of repairing vehicles to restore their original look and functionality and are not original/genuine/OE/OEM/OES replacement parts. Our products are delivered without instruction of installation. Installation of our product may only be carried out by trained specialist technicians in specific car repairs. Products supplied by us are exclusively intended for proper and appropriate use. The warranty may become invalid in the event of: improper installation or repair, unsuitable application or use, installation or repair made outside specialist car workshops. Warranty claims are lost if the vehicle is modified and used for motor sports, tuning or similar events (except our tuning parts which are described in TecDoc and on our price list). Warranty application should include complete documentation among others: chassis no., first registration, vehicle mileage, information about LPG installation, fault memory log, pictures, our QC (quality check) code, installation invoice, contact details of the car repair workshop performing the replacement or repair. Warranty application are available in our Client Panel system. Complaints may require supplementing data such as error memory logs. Incomplete documentation may result in rejection of the claim. Any damage caused during transport is not considered quality damage and will be considered on an individual basis.

• Water pump impeller material: Plastic
• Seal Material: Rubber
• Material: Cast Aluminium
• Number of Teeth: 19
• Number of blades/vanes: 8
• Weight [kg]: 0.725
• Supplementary Article/Supplementary Info: with seal
• Observe service information:
• Name: SW 30 93 6048
• Manufacturer: SWAG

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Water Pump Type: for timing belt drive
• Number of Teeth: 19
• SVHC: No SVHC present!
• Name: VEEPUMP
• Manufacturer: INA
• Lisainfo: 538006010
• Additional information: 538006010

• Voltage [V]: 12
• Operating Mode: Electric
• for OE number: 7N0965561
• Manufacturer: ABAKUS DEPO/LORO

General Information: The following information is for general and informational purposes only and does not constitute warranty terms. Warranty terms and conditions are available from our dealers and in our general terms and conditions of sale. Abakus spare/repair parts are intended only for vehicle repairs in order to restore their original functionality. Abakus spare/repair parts are used or sold to users only for the purpose of repairing vehicles to restore their original look and functionality and are not original/genuine/OE/OEM/OES replacement parts. Our products are delivered without instruction of installation. Installation of our product may only be carried out by trained specialist technicians in specific car repairs. Products supplied by us are exclusively intended for proper and appropriate use. The warranty may become invalid in the event of: improper installation or repair, unsuitable application or use, installation or repair made outside specialist car workshops. Warranty claims are lost if the vehicle is modified and used for motor sports, tuning or similar events (except our tuning parts which are described in TecDoc and on our price list). Warranty application should include complete documentation among others: chassis no., first registration, vehicle mileage, information about LPG installation, fault memory log, pictures, our QC (quality check) code, installation invoice, contact details of the car repair workshop performing the replacement or repair. Warranty application are available in our Client Panel system. Complaints may require supplementing data such as error memory logs. Incomplete documentation may result in rejection of the claim. Any damage caused during transport is not considered quality damage and will be considered on an individual basis.

• Water Pump Type: for timing belt drive
• Water pump impeller material: Plastic
• Supplementary Article/Supplementary Info: with gaskets/seals
• Number of Teeth: 19
• Manufacturer: SKF
• Name: SK VKPC81269

• Supplementary Article/Info 2: without lid
• Supplementary Article/Supplementary Info: with gaskets/seals
• Weight [kg]: 0.75
• Name: VEEPUMP
• Manufacturer: VAL

• Engine Code: CAYC
• for OE number: 5N0965561
• Operating Mode: Electric
• Voltage [V]: 12
• Name: Lisaveepump
• Manufacturer: MAX

• Operating Mode: Electric
• Lisainfo: Additional Water Pump
• Additional information: Additional Water Pump

• Operating Mode: Electric
• Name: Lisaveepump
• Manufacturer: NRF

• Version: 1
• Connector Shape: oval
• Material: Plastic
• Operating Mode: Electric
• Voltage [V]: 12
• Manufacturer: NISSENS
• Name: NI 831072

• Engine Code: CAYC
• Name: Lisaveepump
• Manufacturer: MAG

• Construction Year to: 05.2010
• Block Separation:
• Construction Year from: 05.2010
• Manufacturer restriction water pump: PIERBURG
• Number of pins: 3
• Pin Shape: Flat
• Plug Type: Male
• Supplementary Article/Info 2: without bracket
• Operating Mode: Electric
• Manufacturer: GATES

• Heating/Cooling: for vehicles with extra heating
• Voltage [V]: 12
• for OE number: 7N0 965 561
• Operating Mode: Electric
• Supplementary Article/Supplementary Info: with holder
• Weight [kg]: 0.431
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Trim Level: AUX
• for OE number: 5N0965561
• Operating Mode: Electric
• Name: Lisaveepump
• Manufacturer: DAY

• Voltage [V]: 12
• Operating Mode: Electric
• Alternatively:
• Article number of recommended accessories: V99-16-0001, V99-16-0002, V99-16-0003, V99-16-0004
• Weight [kg]: 0.227
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Operating Mode: Electric
• Number of pins: 3
• Manufacturer: AIC

General Information: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.

• General Information: additional coolant pump
• Manufacturer: VIKA

• Engine Code: CAYC
• for OE number: 5N0 965 561
• Operating Mode: Electric
• Voltage [V]: 12
• Name: VEEPUMP,SEISUKšTE
• Manufacturer: PIE

• Number of belts: 1
• Weight [kg]: 2.77
• Name: AI WPK-199201
• Manufacturer: AIRTEX

• Driven Units: Camshaft
• Trim Level: HT -KTBWP
• Number of Teeth: 160
• Width [mm]: 25
• Length [mm]: 1,524
• Number of belts: 1
• Pulleys contained: 4
• Weight [kg]: 3.1
• Name: VEEPUMP HAMMASRIHMAKOMPLEKT
• Manufacturer: DAY
• Additional information: KTBWP7880 DAYCO
• Lisainfo: KTBWP7880 DAYCO

• Construction Year from: 05.2010
• Manufacturer restriction water pump: BUEHLER
• Number of pins: 3
• Pin Shape: Flat
• Plug Type: Male
• Operating Mode: Electric
• Manufacturer: GATES

• Length [mm]: 1,524
• Number of Teeth: 160
• Width [mm]: 25
• Tooth Pitch [mm]: 9.525
• Pulleys contained: 4
• Name: VEEPUMP HAMMASRIHMAKOMPLEKT
• Manufacturer: BOS

• Number of Teeth 1: 160
• Width 1 [mm]: 25
• Supplementary Article/Supplementary Info: with water pump
• Observe service information:
• Follow installation instructions:
• SVHC: No SVHC present!
• Name: VEEPUMP HAMMASRIHMAKOMPLEKT
• Manufacturer: INA
• Lisainfo: 530055032
• Additional information: 530055032

• Width [mm]: 25
• Number of Teeth: 160
• Surface: Coated
• Belts: with rounded tooth profile
• Weight [kg]: 2.63
• for OE number: 03L 198 119 F S1
• Supplementary Article/Supplementary Info: with water pump
• Observe service information:
• Name: VEEPUMP HAMMASRIHMAKOMPLEKT
• Manufacturer: FEB

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Number of belts: 1
• Width 1 [mm]: 25
• Number of track rollers: 4
• Number of Teeth 1: 160
• Manufacturer: SNR
• Name: SN KDP457.730

• Article number of the recommended special tool: VKN 1000
• Number of bolts/screws: 2
• Water pump impeller material: Plastic
• Belt Width [mm]: 25
• Supplementary Article/Supplementary Info: with gaskets/seals
• Supplementary Article/Info 2: with studs
• Number of Teeth: 160
• Name: VEEPUMP HAMMASRIHMAKOMPLEKT
• Manufacturer: SKF
• Lisainfo: VKMC 01148-2 SKF
• Additional information: VKMC 01148-2 SKF

• Driven Units: Camshaft
• Article number of the recommended special tool: GAT4840A, GAT4844
• Supplementary Article/Supplementary Info: with water pump
• Observe technical data:
• Name: Veepump hammasrihmakomplekt
• Manufacturer: GAT
• Lisainfo: KP25649XS-1 GAT
• Additional information: KP25649XS-1 GAT

• Driven Units: Camshaft
• Engine Code: CAYC
• Packaging length [cm]: 19.5
• Packaging width [cm]: 18.2
• Packaging height [cm]: 18.7
• Number of Teeth: 160
• Weight [kg]: 2.622
• Width [mm]: 25
• Supplementary Article/Supplementary Info: with camshaft screws
• Manufacturer: CONTITECH

Technical Information: Appropriate crankshaft bolt(s) available separately. See section belt pulley crankshaft (bolt set)

• for OE number: 5N0965561
• Operating Mode: Electric
• Manufacturer Restriction: PIERBURG
• Alternative Repair Kit: 2221050
• Manufacturer: METZGER

• Engine Code: CAYC
• Driven Units: Camshaft, Water Pump
• Width [mm]: 25
• Operating Mode: Mechanical
• Supplementary Article/Supplementary Info: with water pump
• Pulleys contained: 4
• Supplementary Article/Info 2: with fastening material
• Number of belts: 1
• Number of Teeth: 160
• Weight [kg]: 3.383
• Manufacturer: VAICO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.