• Fitting Position: Front Axle Left, Front Axle Right, outer, Lower
• Mounting Type: Rubber-Metal Mount
• Manufacturer: JP GROUP
• Lisainfo: Rubber mount for wishbone, front, outer
• Additional information: Rubber mount for wishbone, front, outer

• Fitting Position: Front Axle Left, Front Axle Right, Lower, inner
• Manufacturer: JP GROUP
• Lisainfo: Rubber mount for wishbone, front
• Additional information: Rubber mount for wishbone, front

Lisainfo: Tie Bar Bush

• Mounting Type: Rubber-Metal Mount
• Material: Rubber/Metal
• Thickness [mm]: 45
• Inner Diameter [mm]: 12
• Outer Diameter [mm]: 44
• Manufacturer: MERTZ

Fitting Position: Front Axle Left, Front Axle Right, Lower, Front, outer

• Fitting Position: Front Axle, Lower, Centre
• Mounting Type: Rubber-Metal Mount
• Inner Diameter [mm]: 12
• Outer Diameter [mm]: 43
• Height [mm]: 45
• Manufacturer: DELLO AUTOMEGA

• Fitting Position: Front Axle Left, Upper, Front Axle Right
• Manufacturer: GSP

• Diameter [mm]: 46
• Mounting Type: Rubber-Metal Mount
• Height [mm]: 40
• Axle alignment required after fitting:
• Fitting Position: both sides, inner, Upper Front Axle
• Control/Trailing Arm Type: for control arm
• Weight [kg]: 0.103
• Manufacturer: VAICO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Mounting Type: Rubber-Metal Mount
• Fitting Position: mounting
• Name: Control arm bush left=right
• Quality class: PJ

Lisainfo: "Tootja: TEKNOROT
AUDI A4/6/8/ VW PASS
(kvaliteediklass: PJ)" Additional information: "Tootja: TEKNOROT
AUDI A4/6/8/ VW PASS
(kvaliteediklass: PJ)"

• Fitting Position: Front Axle, Front, Lower
• Inner Diameter [mm]: 12
• Outer Diameter [mm]: 44
• for OE number: 4E0407181B
• paired article number: 2256054
• Manufacturer: SASIC

Lisainfo: Tie Bar Bush

• Fitting Position: Front Axle Right, Front Axle Left, inner, Lower
• Height [mm]: 60
• Inner Diameter [mm]: 12
• Outer Diameter [mm]: 55
• Control/Trailing Arm Type: for control arm
• Mounting Type: Rubber-Metal Mount
• Manufacturer: DELLO AUTOMEGA

• Fitting Position: Lower, Front, Front Axle Left, Front Axle Right
• Control/Trailing Arm Type: for control arm
• Name: Control arm bush left=right
• Quality class: PJ

Lisainfo: "Tootja: SRL
A.A6/A8/VW PHEATON
(kvaliteediklass: PJ)" Additional information: "Tootja: SRL
A.A6/A8/VW PHEATON
(kvaliteediklass: PJ)"

• Fitting Position: Lower, Front, Front Axle Left, Front Axle Right
• Control/Trailing Arm Type: for control arm
• Name: Control arm bush left=right
• Quality class: PJ

Lisainfo: "Tootja: SRL
A.A6/A8/VW THEATON
(kvaliteediklass: PJ)" Additional information: "Tootja: SRL
A.A6/A8/VW THEATON
(kvaliteediklass: PJ)"

• Fitting Position: Front Axle both sides, Upper
• Inner Diameter [mm]: 10
• Outer Diameter [mm]: 33
• Name: ALT 80928AL
• Manufacturer: ALTE AUTOMOTIVE

• Fitting Position: Front Axle, Lower, Front, outer
• Inner Diameter [mm]: 12
• Outer Diameter [mm]: 40
• Height [mm]: 50
• Name: ALT 80989AL
• Manufacturer: ALTE AUTOMOTIVE

• Inner Diameter 1 [mm]: 60
• Outer Diameter 1 [mm]: 12
• Thickness 1 [mm]: 46
• Manufacturer: DELPHI
• Name: DE TD1246W

Fitting Position: Rear Axle, in front of axle, both sides, outer, Lower

• Total Length [mm]: 60
• Inner Diameter [mm]: 12.2
• Outer Diameter [mm]: 43.8
• Fitting Position: Rear Axle
• Name: COC 80005087
• Manufacturer: CORTECO

• Fitting Position: Rear Axle
• Mounting Type: Rubber-Metal Mount
• Control/Trailing Arm Type: for control arm
• Weight [kg]: 0.07
• Name: DY 37-22745
• Manufacturer: DYS

• Fitting Position: outer, Lower, Front Axle Left, Front Axle Right
• Outer Diameter 1 [mm]: 44
• Inner Diameter 1 [mm]: 12
• Thickness 1 [mm]: 45
• Manufacturer: BGA

• Fitting Position: Upper, Rear Axle Left, Rear Axle Right
• Control/Trailing Arm Type: Control Arm
• Mounting Type: Rubber-Metal Mount
• Name: Control arm bush left=right
• Quality class: PJ

Lisainfo: "Tootja: SRL
AUDI A6 '04-
(kvaliteediklass: PJ)" Additional information: "Tootja: SRL
AUDI A6 '04-
(kvaliteediklass: PJ)"

• Fitting Position: Front Axle both sides, Upper, inner
• Mounting Type: Rubber-Metal Mount
• Control/Trailing Arm Type: for control arm
• Outer Diameter [mm]: 46.4
• Inner Diameter [mm]: 10
• Length [mm]: 40
• Weight [kg]: 0.088
• Manufacturer: RTS

• Thickness [mm]: 60
• Inner Diameter [mm]: 12
• Outer Diameter [mm]: 46
• Fitting Position: Rear Axle Left, Rear Axle Right
• Weight [kg]: 0.12
• Name: Puks - K„„ndmik VW T. A4 00- LE/PR
• Manufacturer: FEB

Technical Information: Please tighten the mounting bolts with the wheels on the ground. General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Fitting Position: Right, Left, outer, Front Axle
• Total Length [mm]: 45
• Inner Diameter [mm]: 12.1
• Outer Diameter [mm]: 44
• Name: COC 80004748
• Manufacturer: CORTECO

• Fitting Position: Rear Axle Lower, Rear, both sides, outer
• Control/Trailing Arm Type: for control arm
• Mounting Type: Rubber-Metal Mount
• Material: Rubber/Metal
• Required quantity: 2
• Name: Puks
• Manufacturer: TED

• Control/Trailing Arm Type: for control arm
• Mounting Type: Rubber-Metal Mount
• Fitting Position: outer, both sides, Front, Lower Front Axle
• Axle alignment required after fitting:
• Weight [kg]: 0.085
• Manufacturer: VAICO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Fitting Position: Rear Axle Lower, inner, Lower
• Manufacturer: GSP

• Fitting Position: Front Axle, outer
• Mounting Type: Rubber-Metal Mount
• Control/Trailing Arm Type: for control arm
• Weight [kg]: 0.16
• Name: DY 37-06164-5
• Manufacturer: DYS

• Thickness [mm]: 60
• Inner Diameter [mm]: 12
• Outer Diameter [mm]: 46
• Fitting Position: Rear Axle Left, Rear Axle Right
• Weight [kg]: 0.12
• Name: SW 30 93 0687
• Manufacturer: SWAG

Technical Information: Please tighten the mounting bolts with the wheels on the ground. General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Fitting Position: outer, Rear Axle both sides, Lower
• Required quantity: 2
• Name: SK VKDS431017
• Manufacturer: SKF

• Height [mm]: 60
• Inner Diameter [mm]: 12
• Outer Diameter [mm]: 44
• Supplementary Article/Supplementary Info: without holder
• Required quantity: 2
• replacement in pairs recommended:
• Name: Puks - K„„ndmik VW T. A4 00- LE/PR
• Manufacturer: MEY

Fitting Position: outer, Rear Axle Right, Rear Axle Left, Front, Lower

• Fitting Position: Front Axle both sides, Lower, outer, Front
• Outer Diameter [mm]: 44
• Inner Diameter [mm]: 12.3
• Length [mm]: 45
• Weight [kg]: 0.104
• Manufacturer: RTS

• Fitting Position: Front Axle, Lower, Front, inner
• Inner Diameter [mm]: 12
• Outer Diameter [mm]: 24
• Height [mm]: 60
• Name: ALT 80990AL
• Manufacturer: ALTE AUTOMOTIVE

• Fitting Position: in front of axle, outer, Lower Front Axle
• Weight [kg]: 0.112
• Packaging length [cm]: 4.9
• Packaging width [cm]: 4.4
• Packaging height [cm]: 4.4
• Manufacturer: FEBEST

• Fitting Position: Front, Rear Axle Lower, outer
• Weight [kg]: 0.246
• Packaging length [cm]: 6
• Packaging width [cm]: 5.3
• Packaging height [cm]: 5.3
• Manufacturer: FEBEST

• Fitting Position: outer, Lower, Front, Front Axle both sides
• Required quantity: 2
• paired article number: VKDS 331028
• Length [mm]: 45
• Height [mm]: 43.8
• Inner Diameter [mm]: 12.1
• Outer Diameter [mm]: 43.8
• Name: SK VKDS331028
• Manufacturer: SKF

• Fitting Position: Rear Axle both sides
• Inner Diameter [mm]: 12
• Outer Diameter [mm]: 44
• Height [mm]: 60
• Name: ALT 98282AL
• Manufacturer: ALTE AUTOMOTIVE

• Length [mm]: 37.8
• Width [mm]: 40.4
• Thickness [mm]: 37.8
• Inner Diameter [mm]: 12.3
• Outer Diameter [mm]: 40
• Material: Rubber/Metal
• Weight [kg]: 0.13
• Name: Puks
• Manufacturer: FEB

Fitting Position: Rear Axle Left, Lower, Rear, inner, Rear Axle Right General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Fitting Position: Rear Axle, Upper, inner, outer
• Inner Diameter [mm]: 12
• Outer Diameter [mm]: 36
• Height [mm]: 46
• Name: ALT 88956AL
• Manufacturer: ALTE AUTOMOTIVE

• Fitting Position: Rear Axle
• Mounting Type: Rubber-Metal Mount
• Control/Trailing Arm Type: for control arm
• Weight [kg]: 0.09
• Name: DY 37-24926
• Manufacturer: DYS

• Fitting Position: Rear Axle, Lower, Front, outer
• Inner Diameter [mm]: 12.2
• Outer Diameter 1 [mm]: 52
• Outer Diameter 2 [mm]: 44
• Width [mm]: 60
• SVHC: No SVHC present!
• Name: LU 829059810
• Manufacturer: FAG

• Length [mm]: 37.8
• Width [mm]: 40.4
• Thickness [mm]: 37.8
• Inner Diameter [mm]: 12.3
• Outer Diameter [mm]: 40
• Material: Rubber/Metal
• Weight [kg]: 0.13
• Name: SW 30 10 4781
• Manufacturer: SWAG

Fitting Position: Rear Axle Left, Lower, Rear, inner, Rear Axle Right General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Fitting Position: inner, Rear Axle Lower, Centre
• Weight [kg]: 0.135
• Packaging length [cm]: 4.1
• Packaging width [cm]: 4.1
• Packaging height [cm]: 3.8
• Manufacturer: FEBEST

• Fitting Position: Front Axle, both sides, Lower
• Inner Diameter [mm]: 12
• Outer Diameter [mm]: 65
• Manufacturer: DENCKERMANN ZAWIESZENIE

• Fitting Position: Front Axle, both sides, Upper, inner, Front, Rear
• Block Separation:
• Inner Diameter [mm]: 10
• Outer Diameter [mm]: 46.5
• Width 1 [mm]: 26
• Width 2 [mm]: 40
• SVHC: No SVHC present!
• Manufacturer: FAG

• Fitting Position: Front Axle, outer, Lower, Front
• Inner Diameter 1 [mm]: 12
• Outer Diameter 1 [mm]: 44
• Thickness 1 [mm]: 45
• Manufacturer: DELPHI
• Name: DE TD723W

• Fitting Position: Rear Axle, both sides, Lower, outer
• Mounting Type: Rubber-Metal Mount
• Inner Diameter [mm]: 12.2
• Outer Diameter [mm]: 41.3
• Width [mm]: 45
• SVHC: No SVHC present!
• Manufacturer: FAG

• Fitting Position: Front Axle both sides, Lower, Front, outer
• Inner Diameter [mm]: 13
• Outer Diameter [mm]: 44
• Height [mm]: 45
• Name: ALT 84050AL
• Manufacturer: ALTE AUTOMOTIVE

• Fitting Position: Front Axle, Rear, Lower
• Inner Diameter [mm]: 12
• Outer Diameter [mm]: 65
• for OE number: 4F0407183E
• Manufacturer: SASIC

• Spring Type: for vehicles without air suspension
• not for PR number: 1BK
• Fitting Position: inner, Upper, Rear, Rear Axle
• Height [mm]: 46
• Inner Diameter [mm]: 12
• Outer Diameter [mm]: 36
• Supplementary Article/Supplementary Info: without holder
• Required quantity: 4
• replacement in pairs recommended:
• Name: Puks - K„„ndmik VW T. A6 04- GàRNA
• Manufacturer: MEY

• Mounting Type: Rubber-Metal Mount
• Fitting Position: mounting
• Name: Control arm bush left=right
• Quality class: PJ

Lisainfo: "Tootja: TEKNOROT
A.A6/A8/VW THEATON
(kvaliteediklass: PJ)" Additional information: "Tootja: TEKNOROT
A.A6/A8/VW THEATON
(kvaliteediklass: PJ)"

• Length [mm]: 45
• Width [mm]: 41.5
• Thickness [mm]: 45
• Inner Diameter [mm]: 12.3
• Outer Diameter [mm]: 41.5
• Material: Rubber/Metal
• Weight [kg]: 0.25
• Manufacturer: SWAG

Fitting Position: Rear Axle Left, Lower, Rear, outer, Rear Axle Right General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Fitting Position: Front, Front Axle, inner, Lower
• Inner Diameter [mm]: 12.2
• Outer Diameter [mm]: 64.5
• Length [mm]: 80
• paired article number: 270760
• Weight [kg]: 0.29
• Installation Information: Important: Observe Fitting Instructions
• Manufacturer: A.B.S.

• Fitting Position: Rear Axle Upper, Rear, outer
• Weight [kg]: 0.132
• Packaging length [cm]: 4.6
• Packaging width [cm]: 3.7
• Packaging height [cm]: 3.7
• Manufacturer: FEBEST

• Fitting Position: Front Axle, Lower, Rear, inner, both sides
• Required quantity: 2
• Manufacturer: TEDGUM

• Thickness [mm]: 45
• Inner Diameter [mm]: 12
• Outer Diameter [mm]: 44
• Material: Rubber/Metal
• Mounting Type: Rubber-Metal Mount
• Weight [kg]: 0.06
• Observe service information:
• Name: Puks - K„„ndmik VW P. A6 04-/A8 02- DOLNA LE/PR
• Manufacturer: FEB

Fitting Position: Front Axle Left, Lower, Front, outer, Front Axle Right Technical Information: Please tighten the mounting bolts with the wheels on the ground. General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Mounting Type: Rubber-Metal Mount
• Fitting Position: mounting
• Name: Control arm bush left=right
• Quality class: PJ

Lisainfo: "Tootja: TEKNOROT
A.A6/A8/VW THEATON
(kvaliteediklass: PJ)" Additional information: "Tootja: TEKNOROT
A.A6/A8/VW THEATON
(kvaliteediklass: PJ)"

• Fitting Position: both sides, inner, Front, Lower Front Axle
• Control/Trailing Arm Type: for control arm
• Mounting Type: Rubber-Metal Mount
• Axle alignment required after fitting:
• Weight [kg]: 0.373
• Manufacturer: VAICO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Fitting Position: Rear Axle Lower, Upper, outer, Centre
• Weight [kg]: 0.236
• Packaging length [cm]: 4.5
• Packaging width [cm]: 4.2
• Packaging height [cm]: 4.2
• Manufacturer: FEBEST

• Fitting Position: Front Axle Left, Front Axle Right
• Manufacturer: BGA

• Braking/Drive Dynamics: for vehicles without ABS
• Fitting Position: inner, Front, Rear Axle Lower
• Name: Puks
• Manufacturer: MAX

• Thickness [mm]: 45
• Inner Diameter [mm]: 12
• Outer Diameter [mm]: 44
• Material: Rubber/Metal
• Mounting Type: Rubber-Metal Mount
• Weight [kg]: 0.06
• Observe service information:
• Manufacturer: SWAG
• Name: SW 30 92 7484

Fitting Position: Front Axle Left, Lower, Front, outer, Front Axle Right Technical Information: Please tighten the mounting bolts with the wheels on the ground. General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Mounting Type: Rubber-Metal Mount
• Fitting Position: mounting
• Quality class: PJ
• Name: Control arm bush left=right

Lisainfo: "Tootja: TEKNOROT
A.A6/A8/VW PHEATON
(kvaliteediklass: PJ)" Additional information: "Tootja: TEKNOROT
A.A6/A8/VW PHEATON
(kvaliteediklass: PJ)"

• Fitting Position: Rear Axle Lower, Rear, outer, both sides
• Mounting Type: Rubber-Metal Mount
• Control/Trailing Arm Type: for control arm
• for OE number: 8E0501529G, 8E0501529K, 4F0501529C
• Manufacturer: TRW

SVHC: No information available, please contact the manufacturer!

• Fitting Position: Front Axle, outer
• Mounting Type: Rubber-Metal Mount
• Inner Diameter [mm]: 12.4
• Outer Diameter [mm]: 43.8
• Width [mm]: 45
• SVHC: No SVHC present!
• Manufacturer: FAG

• Fitting Position: Rear Axle, Rear Axle Left, Rear Axle Right
• Fabrication Number: ZTT-AU-001A
• Manufacturer: NTY

Lisainfo: AUDI A4 (8E) 00-08, A4 AVANT (8ED) 04-, A6 AVANT (4F5) 05-, SEAT EXEO/ST 09- /TYLNEGO DOLNEGO/ Additional information: AUDI A4 (8E) 00-08, A4 AVANT (8ED) 04-, A6 AVANT (4F5) 05-, SEAT EXEO/ST 09- /TYLNEGO DOLNEGO/

• Fitting Position: Rear Axle, both sides, Upper, Rear, inner
• not for PR number: 1BK
• Mounting Type: Rubber-Metal Mount
• Inner Diameter [mm]: 12
• Outer Diameter [mm]: 36
• Width 1 [mm]: 34
• Width 2 [mm]: 46
• SVHC: No SVHC present!
• Manufacturer: FAG

• Mounting Type: Rubber-Metal Mount
• Fitting Position: mounting
• Name: Control arm bush left=right
• Quality class: PJ

Lisainfo: "Tootja: TEKNOROT
AUDI A4/6/8/ VW PASS
(kvaliteediklass: PJ)" Additional information: "Tootja: TEKNOROT
AUDI A4/6/8/ VW PASS
(kvaliteediklass: PJ)"

• Mounting Type: Rubber-Metal Mount
• Fitting Position: mounting
• Name: Control arm bush left=right
• Quality class: PJ

Lisainfo: "Tootja: TEKNOROT
AUDI A4 08-
(kvaliteediklass: PJ)" Additional information: "Tootja: TEKNOROT
AUDI A4 08-
(kvaliteediklass: PJ)"

• for PR number: D70
• Weight [kg]: 0.091
• Quantity: 10
• Packaging length [cm]: 4
• Packaging width [cm]: 4
• Packaging height [cm]: 1.2
• Manufacturer: FEBEST

• Fitting Position: Front Axle both sides, Lower, Rear
• Inner Diameter [mm]: 12
• Outer Diameter [mm]: 65
• Height [mm]: 80
• Name: ALT 84083AL
• Manufacturer: ALTE AUTOMOTIVE

• Height [mm]: 45
• Inner Diameter [mm]: 12
• Outer Diameter [mm]: 44
• Supplementary Article/Supplementary Info: without holder
• reinforced version:
• Required quantity: 2
• Replace in pairs only:
• with environmental seal: Carbon neutral
• Name: Puks - K„„ndmik VW P. A6 04-/A8 02- DOLNA LE/PR
• Manufacturer: MEY
• Lisainfo: 1006100003/HD
• Additional information: 1006100003/HD

Fitting Position: Front Axle Right, Front Axle Left, Lower, Front, outer General Information: 4-year warranty on all MEYLE-HD parts. Engineered and quality approved in Germany.

• Fitting Position: Front Axle, inner, Lower, Front
• Inner Diameter 1 [mm]: 12
• Outer Diameter 1 [mm]: 55
• Thickness 1 [mm]: 60
• Manufacturer: DELPHI

• Thickness [mm]: 60
• Inner Diameter [mm]: 12
• Outer Diameter [mm]: 55, 28
• Material: Rubber/Metal
• Weight [kg]: 0.199
• Manufacturer: FEBI BILSTEIN

Fitting Position: Front Axle Left, Lower, Front, inner, Front Axle Right Technical Information: Please tighten the mounting bolts with the wheels on the ground. General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Mounting Type: Rubber-Metal Mount
• Control/Trailing Arm Type: for control arm
• Fitting Position: Front Axle, Lower, both sides, Front, inner
• Manufacturer: TRW

for OE number: 4F0407151, 4F0407151A, 4E0407151K, 4E0407151J, 4E0407151E, 4E0407151L, 4E0407151G SVHC: No information available, please contact the manufacturer!

• Fitting Position: Front Axle, both sides, Lower, Front, outer
• Control/Trailing Arm Type: for control arm
• Quantity per axle: 2
• Article number of recommended accessories: 39097 01, 39364 01, 44252 01
• Observe service information:
• Name: Puks - K„„ndmik VW P. A6 04-/A8 02- DOLNA LE/PR
• Manufacturer: LMI

SVHC: No information available, please contact the manufacturer!

• Mounting Type: Rubber-Metal Mount
• Fitting Position: mounting
• Name: Control arm bush left=right
• Quality class: PJ

Lisainfo: "Tootja: TEKNOROT
AUDI A4/6/8/ VW PASS
(kvaliteediklass: PJ)" Additional information: "Tootja: TEKNOROT
AUDI A4/6/8/ VW PASS
(kvaliteediklass: PJ)"

• Height [mm]: 60
• Inner Diameter [mm]: 12
• Outer Diameter [mm]: 55
• Supplementary Article/Supplementary Info: without holder
• reinforced version:
• Required quantity: 2
• Replace in pairs only:
• with environmental seal: Carbon neutral
• Name: Puks - K„„ndmik VW P. A6/A8 DOLNEG
• Manufacturer: MEY

Fitting Position: Front Axle Right, Front Axle Left, Lower, Front, inner General Information: 4-year warranty on all MEYLE-HD parts. Engineered and quality approved in Germany.

• Mounting Type: Rubber-Metal Mount
• Fitting Position: mounting
• Name: Control arm bush left=right
• Quality class: PJ

Lisainfo: "Tootja: TEKNOROT
AUDI A4 05-/A6 04-
(kvaliteediklass: PJ)" Additional information: "Tootja: TEKNOROT
AUDI A4 05-/A6 04-
(kvaliteediklass: PJ)"

• Fitting Position: Front Axle, Lower, both sides, Front, inner
• Control/Trailing Arm Type: for control arm
• Quantity per axle: 2
• Article number of recommended accessories: 39097 01
• Observe service information:
• Name: Puks - K„„ndmik VW P. A6/A8 DOLNEG
• Manufacturer: LMI

SVHC: No information available, please contact the manufacturer!

• Thickness [mm]: 80
• Inner Diameter [mm]: 12
• Outer Diameter [mm]: 65, 28
• Material: Rubber/Metal
• Fitting Position: Front Axle Left, Lower, Rear, Front Axle Right
• Mounting Type: Rubber-Metal Mount
• Shape: oval
• Weight [kg]: 0.313
• Observe service information:
• Manufacturer: FEBI

Technical Information: Please tighten the mounting bolts with the wheels on the ground. General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Thickness [mm]: 80
• Inner Diameter [mm]: 12.1
• Outer Diameter [mm]: 65, 28
• Material: Rubber/Metal
• Fitting Position: Front Axle Left, Lower, Rear, Front Axle Right
• Mounting Type: Rubber-Metal Mount
• Shape: oval
• Weight [kg]: 0.3
• Observe service information:
• Manufacturer: SWAG

Technical Information: Please tighten the mounting bolts with the wheels on the ground. General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Fitting Position: Rear Axle Lower, outer, Lower
• Weight [kg]: 0.198
• Packaging length [cm]: 4.6
• Packaging width [cm]: 4.6
• Packaging height [cm]: 4
• Manufacturer: FEBEST