Assembly categories
Filter Brakes Suspension Steering Cooling/Air Conditioning Electrics Accessories Drive Train Exhaust System Body Spark/Glow Ignition Engine Windows/Window Cleaning Lights Fuel Mixture Formation Interior Equipment ServiceProduct
Description
In stock
Price
(incl. VAT)
-
Engine Code: CCZA,
BPY, BWA, AXX -
Axle Gear ID: KMC,
MMK - Fitting Position: Rear Axle
-
Drive Type: All-
wheel Drive - Clutch Type: for wet clutch
- Supplementary Article/Supplementary Info: with gaskets
- Number of sealing rings: 2
- Gasket inner diameter: 34
- Seal Ring Outer Diameter: 39
- Sealing ring colour: black
-
Supplementary Article/Info 2: with bolts/
screws - Number of bolts/screws: 2
- Thread Size: M 5 x 25
-
Clutch ID: HALDEX GEN IV
(4) -
Name: ZESTAW USZCZELEK POMPY HALDEX VW TIGUAN 08-
18 - Manufacturer: HAN
General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.
- Fitting Position: Rear Axle
- Shape: Cylindrical
-
Filter type: Filter Insert,
with housing cover - Supplementary Article/Info 2: with seal ring
- Observe system fill quantity:
-
Fabrication Number: FHO-
VW- 001 -
Name: NTY FHO-
VW- 001 - Manufacturer: NTY
Tavatellimus saadetakse E, K ja R kell 14:00. Kaup saabub kuni 3 tööpäevaga. Tavatellimusse lähevad ainult positiivse laojäägiga tooted. Lisaks tavatellimusele on võimalik tellida ka Express kulleriga (24h). Kulleri hinda täpsusta 6 599 702, malva@lakiauto.ee.
Tavatellimus saadetakse E, K ja R kell 14:00. Kaup saabub kuni 3'e tööpäevaga. Tavatellimusse lähevad ainult positiivse laojäägiga tooted. Lisaks tavatellimusele on võimalik tellida ka Express kulleriga (24h). Kulleri hinda täpsusta 6 599 702, malva@lakiauto.ee.
-
Engine Code: CCZA,
BPY, BWA, AXX - Fitting Position: Rear Axle
-
Filter type: Filter Insert,
with housing cover - Supplementary Article/Info 2: with seal ring
- Observe system fill quantity:
- Shape: Cylindrical
- Manufacturer Restriction: HALDEX Gen. II
-
Name: Olifilter,
diferentsiaal - Manufacturer: MAX
- Fitting Position: Rear Axle
- Transmission Type: for transfer case
-
Transmission Code: HALDEX GEN IV/
GEN 4 - Filter type: Filter Insert
- Supplementary Article/Supplementary Info: with seal
- Supplementary Article/Info 2: with lid
- Manufacturer: MAX
-
Lisainfo: 26-
2086 -
Additional information: 26-
2086
Name: Hdraulikafilter, tisveoga soiduki mitme kettaga sidur
Fabrication Number: FHO-VW-003
Tavatellimus saadetakse E, K ja R kell 14:00. Kaup saabub kuni 3 tööpäevaga. Tavatellimusse lähevad ainult positiivse laojäägiga tooted. Lisaks tavatellimusele on võimalik tellida ka Express kulleriga (24h). Kulleri hinda täpsusta 6 599 702, malva@lakiauto.ee.
Tavatellimus saadetakse E, K ja R kell 14:00. Kaup saabub kuni 3'e tööpäevaga. Tavatellimusse lähevad ainult positiivse laojäägiga tooted. Lisaks tavatellimusele on võimalik tellida ka Express kulleriga (24h). Kulleri hinda täpsusta 6 599 702, malva@lakiauto.ee.
- Fitting Position: Rear Axle
- Supplementary Article/Supplementary Info: with accessories
- Clutch Type: for wet clutch
-
Filter type: with housing cover,
Filter Insert -
Supplementary Article/Info 2: with bolts/
screws, with seal ring -
Clutch ID: HALDEX GEN IV /
4 - Model Year from: 2009
-
Fabrication Number: FHO-
VW- 002 - Manufacturer: NTY
-
Name: NTY FHO-
VW- 002
Tavatellimus saadetakse E, K ja R kell 14:00. Kaup saabub kuni 3 tööpäevaga. Tavatellimusse lähevad ainult positiivse laojäägiga tooted. Lisaks tavatellimusele on võimalik tellida ka Express kulleriga (24h). Kulleri hinda täpsusta 6 599 702, malva@lakiauto.ee.
Tavatellimus saadetakse E, K ja R kell 14:00. Kaup saabub kuni 3'e tööpäevaga. Tavatellimusse lähevad ainult positiivse laojäägiga tooted. Lisaks tavatellimusele on võimalik tellida ka Express kulleriga (24h). Kulleri hinda täpsusta 6 599 702, malva@lakiauto.ee.
- Vehicle type: AXX
-
Vehicle Identification Number (VIN) to: 8P-
8A250000, 8P- 8B050000 - Fitting Position: Rear Axle
-
Filter type: Filter Insert,
with housing cover - Supplementary Article/Info 2: with seal ring
- Shape: Cylindrical
- Manufacturer Restriction: HALDEX Gen. II
- Observe system fill quantity:
- Manufacturer: ENERGY
-
Recommended change interval [km]: 30,
000 - Recommended change interval [years]: 3
- Clutch Type: for wet clutch
- Supplementary Article/Supplementary Info: with accessories
-
Clutch ID: HALDEX GEN II /
2 -
Filter type: with housing cover,
Filter Insert - Height [mm]: 55
- Supplementary Article/Info 2: with seal ring
- See accessories list for additionally required parts:
- Fitting Position: Rear Axle
- Outer Diameter [mm]: 53
- Weight [kg]: 0.151
- Manufacturer: VAICO
-
Lisainfo: V10-
2686 VAI -
Additional information: V10-
2686 VAI
General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.
- Construction Year to: 06.2008
- Fitting Position: Rear Axle
- Transmission Type: for transfer case
-
Transmission Code: HALDEX GEN II/
GEN 2 - Filter type: Filter Insert
-
Supplementary Article/Supplementary Info: with seal,
with spring - Supplementary Article/Info 2: with lid
- Manufacturer: METZGER
- Transmission Type: Differential Gear
-
Axle Gear ID: MMK,
KMC - Block Separation:
- Height [mm]: 61
- Inner Diameter [mm]: 5
- Outer Diameter [mm]: 38
- Weight [kg]: 0.1
-
Supplementary Article/Info 2: with bolts/
screws, with cap -
Supplementary Article/Supplementary Info: for multi-
plate clutch - Manufacturer: BLUE PRINT
General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.
-
Clutch ID: HALDEX GEN IV /
4 - Supplementary Article/Supplementary Info: with accessories
- Clutch Type: for wet clutch
-
Filter type: with housing cover,
Filter Insert - Recommended change interval [years]: 3
-
Recommended change interval [km]: 30,
000 - Fitting Position: Rear Axle
-
Supplementary Article/Info 2: with bolts/
screws, with seal ring - Model Year from: 2009
- Weight [kg]: 0.113
- Manufacturer: VAICO
General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.
-
Oil - manufacturer recommendation: G 060,
G 060 175 A2 - Fitting Position: Rear Axle
- Supplementary Article/Supplementary Info: with oil drain plug
- Clutch Type: for wet clutch
-
Recommended change interval [km]: 30,
000 - Recommended change interval [years]: 3
-
Clutch ID: HALDEX GEN IV /
4, HALDEX GEN V / 5 - Capacity [litre]: 0.85
- Manufacturer: VAICO
Supplementary Article/Info 2: without filter, with oil quantity for standard oil change General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.
- Clutch Type: for wet clutch
-
Filter type: with housing cover,
Filter Insert -
Clutch ID: HALDEX GEN IV /
4 -
Recommended change interval [km]: 30,
000 - Supplementary Article/Supplementary Info: with oil drain plug
- Quantity Unit: Set
- Recommended change interval [years]: 3
- Fitting Position: Rear Axle
- Capacity [litre]: 0.85
- Manufacturer: VAICO
Supplementary Article/Info 2: with bolts/screws, with seal ring, with filter, with oil quantity for standard oil change General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.
- Fitting Position: Rear Axle
- Supplementary Article/Supplementary Info: with oil drain plug
- Quantity Unit: Set
- Clutch Type: for wet clutch
-
Filter type: with housing cover,
Filter Insert -
Recommended change interval [km]: 30,
000 - Recommended change interval [years]: 3
-
Clutch ID: HALDEX GEN II /
2 - Capacity [litre]: 0.85
- Manufacturer: VAICO
Supplementary Article/Info 2: with bolts/screws, with seal ring, with oil quantity for standard oil change General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.
-
Supplementary Article/Info 2: with seal ring,
with bolts/ screws - Supplementary Article/Supplementary Info: with attachment material
- Fitting Position: Rear Axle
-
Operating Mode: Electric-
hydraulic -
Clutch ID: HALDEX GEN II /
2 - Manufacturer: VAICO
General Information: Products supplied by us are without exception intended for the designated use. Please note that our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist personnel. There is no guarantee for inappropriate, improper or unintended use.
-
Supplementary Article/Info 2: with bolts/
screws, with seal ring - Supplementary Article/Supplementary Info: with attachment material
- Fitting Position: Rear Axle
-
Operating Mode: Electric-
hydraulic -
Clutch ID: HALDEX GEN IV /
4 - Manufacturer: VAICO
General Information: Products supplied by us are without exception intended for the designated use. Please note that our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist personnel. There is no guarantee for inappropriate, improper or unintended use.
-
Vehicle Identification Number (VIN) to: 8P-
8- 999 999 - Fitting Position: Rear Axle
-
Operating Mode: Electric-
hydraulic - Number of pins: 2
- Manufacturer: METZGER
- Supplementary Article/Supplementary Info: with attachment material
-
Clutch ID: HALDEX GEN II /
2 -
Operating Mode: Electric-
hydraulic - Fitting Position: Rear Axle
- Capacity [litre]: 0.85
- Manufacturer: VAICO
Supplementary Article/Info 2: with filter, with seal ring, with bolts/screws, with oil quantity for standard oil change General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.
-
Vehicle Identification Number (VIN) from: 8P-
9- 000 001 - Fitting Position: Rear Axle
-
Operating Mode: Electric-
hydraulic - Number of pins: 2
- Manufacturer: METZGER
for OE number: 09N 525 554 A, 0BS 525 554 B, 0BS 525 554 C, 0BY 525 554 A, 2K0 525 554 A
-
Clutch ID: HALDEX GEN IV /
4 - Fitting Position: Rear Axle
-
Operating Mode: Electric-
hydraulic - Supplementary Article/Supplementary Info: with attachment material
- Capacity [litre]: 0.85
- Manufacturer: VAICO
Supplementary Article/Info 2: with filter, with bolts/screws, with seal ring, with oil quantity for standard oil change General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.
Laki Auto universal products
TecDoc catalogue for cars
TecDoc catalogue for trucks