• Number of pins: 2
• Colour: blue
• Manufacturer: JP GROUP A/S
• Lisainfo: Temperature sensor for cooling system, 2 pins
• Additional information: Temperature sensor for cooling system, 2 pins

• Colour Coding: grey
• Number of pins: 2
• Manufacturer: JP GROUP
• Lisainfo: Sender for water temperature gauge, 2 pins
• Additional information: Sender for water temperature gauge, 2 pins

• Outer Diameter [mm]: 18.8
• Manufacturer: FAST

General Information: 5-year warranty FAST offers up to 5 years warranty on this product, throughout the entire EU. The guarantee covers manufacturing and material defects. In the event of problems, we will refund you for the part or replace it with a new one. Details and warranty restrictions can be found at fastoriginal.eu

• for OE number: 049919563B
• Thread Size: M10x1 mm
• Spanner Size: 13 mm
• Number of pins: 1
• Manufacturer: KAMOKA
• Additional information: 4080049 KAMOKA
• Lisainfo: 4080049 KAMOKA

• Vehicle Equipment: for vehicles with automatic climate control
• Connector Shape: rectangular
• Sensor Type: NTC Sensor
• Number of pins: 2
• Colour Coding: blue
• Manufacturer: HANS PRIES
• Lisainfo: 100 191 HP
• Additional information: 100 191 HP

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Number of pins: 2
• Supplementary Article/Info 2: without cable
• Connector Shape: rectangular
• Fabrication Number: ECP-AU-027
• Manufacturer: NTY

• for OE number: 025906041A
• Housing Colour: blue
• Manufacturer: KAMOKA

• Construction Year to: 07.1996
• Engine Code: 1Z
• Manufacturer: AIC
• Lisainfo: 51913 AIC
• Additional information: 51913 AIC

General Information: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.

• Colour Coding: blue
• Number of pins: 1
• Measuring Range to [°C]: 180
• Thread Size: M 10
• Thread Pitch [mm]: 1
• Supplementary Article/Info 2: with seal ring
• Name: ANDUR,OLITEMPERATUUR
• Manufacturer: HAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Operating voltage [V]: 12
• Sensor Type: Passive sensor
• Combi Switch Function: Reed Contact
• Supplementary Article/Info 2: without cable
• Number of pins: 2
• Manufacturer: JP GROUP
• Lisainfo: Distance sensor
• Additional information: Distance sensor

• Number of pins: 2
• Assy./disassy. by qualified personnel required!:
• Manufacturer: ABAKUS LORO

General Information: The following information is for general and informational purposes only and does not constitute warranty terms. Warranty terms and conditions are available from our dealers and in our general terms and conditions of sale. Abakus spare/repair parts are intended only for vehicle repairs in order to restore their original functionality. Abakus spare/repair parts are used or sold to users only for the purpose of repairing vehicles to restore their original look and functionality and are not original/genuine/OE/OEM/OES replacement parts. These items do not originate from the vehicle manufacturer and may be the subject of a design not owned by Abakus and the manufacturer of this spare part. They may only be used for repairs to restore the intended vehicle to its original appearance. Our products are delivered without instruction of installation. Installation of our product may only be carried out by trained specialist technicians in specific car repairs. Products supplied by us are exclusively intended for proper and appropriate use. The warranty may become invalid in the event of: improper installation or repair, unsuitable application or use, installation or repair made outside specialist car workshops. Warranty claims are lost if the vehicle is modified and used for motor sports, tuning or similar events (except our tuning parts which are described in TecDoc and on our price list). Warranty application should include complete documentation among others: chassis no., first registration, vehicle mileage, information about LPG installation, fault memory log, pictures, our QC (quality check) code, installation invoice, contact details of the car repair workshop performing the replacement or repair. Warranty application are available in our Client Panel system. Complaints may require supplementing data such as error memory logs. Incomplete documentation may result in rejection of the claim. Any damage caused during transport is not considered quality damage and will be considered on an individual basis. The product is intended for use within the performance limits specified by the manufacturer and should only be used by qualified personnel who have been trained to operate this product. Before each use, the product should be checked for damage or fixing of its parts and not used if any defects or loose parts are found. Failure to follow the manufacturer's guidelines could result in potential product damage or even injury. Wear appropriate protective clothing if necessary when working with the product.

• General Information: Coolant temperature sensor
• Manufacturer: VIKA

• Fitting Position: Front Axle
• Quantity: 1
• General Information: Speedometer
• Manufacturer: VIKA

• Weight [kg]: 0.2
• Number of connectors: 4
• Outer Diameter [mm]: 20
• Plug Type ID: 4
• Colour: blue
• Supplementary Article/Info 2: with seal ring
• Required quantity: 1
• General Information: Coolant temperature sensor; blue; 4 pins
• Manufacturer: VIKA

Manufacturer: MAGNETI MARELLI

• Engine Code: 1Z
• Number of pins: 2
• Connector Shape: rectangular
• Socket colour: blue
• Diameter [mm]: 25.5
• Fitted Diameter [mm]: 20
• for OE number: 025906041A
• Manufacturer: MEAT&DORIA

• Model Year from: 1995
• Number of pins: 2
• Guarantee: 3 years guarantee
• Weight [kg]: 0.05
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY
• Name: CE 17SKV555

Transmission Type: 5-Speed Manual Transmission, 6-Speed Manual Transmission, 4-Speed Automatic Transmission

• Engine Code: 1Z
• Number of pins: 3
• Switch Point [°C]: 120
• Colour: grey
• Manufacturer: JP GROUP
• Lisainfo: Sender for water temperature gauge 3 pins
• Additional information: Sender for water temperature gauge 3 pins

• Colour: blue
• Number of pins: 2
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: MAX

• Engine Code: AHU
• Number of pins: 4
• Vehicle Identification Number (VIN) from: 8D-Y-000001
• Number of connectors: 4
• Manufacturer: 3RG

• Sensor Type: NTC Sensor
• Mounting Type: Bolted
• Connector Shape: rectangular
• Number of pins: 2
• Socket colour: white
• Spanner Size: 19
• Thread Size: M14x1.5
• for OE number: 035919369M
• Supplementary Article/Info 2: with seal ring
• Name: Andur,Jahutusvedeliku temp.
• Manufacturer: NRF

• Sensor Type: NTC Sensor
• Mounting Type: Clamped
• Connector Shape: rectangular
• Number of pins: 2
• for OE number: 025906041A
• Supplementary Article/Info 2: with mounting parts
• Name: Andur,Jahutusvedeliku temp.
• Manufacturer: NRF

• Sensor Type: NTC Sensor
• Mounting Type: Clamped
• Connector Shape: D Shape
• Number of pins: 2
• for OE number: 06A919501
• Supplementary Article/Info 2: with mounting parts
• Name: Andur,Jahutusvedeliku temp.
• Manufacturer: NRF

• Engine Code: 1Z
• Thread Size: M10 x 1
• Spanner Size: 14
• Supplementary Article/Supplementary Info: with gasket/seal
• Number of pins: 1
• Colour Coding: blue
• Manufacturer: VIEROL

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Connecting thread: M10 x 1
• Manufacturer: ERA

• Supplementary Article/Info 2: with seal ring
• Number of pins: 2
• Manufacturer: AIC

General Information: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.

• Weight [g]: 15
• Name: IM 5309
• Manufacturer: ORIGINAL IMPERIUM

• Sensor Type: NTC Sensor
• Mounting Type: Clamped
• Connector Shape: D Shape
• Number of pins: 4
• for OE number: 059919501A
• Supplementary Article/Info 2: with mounting parts
• Name: Andur,Jahutusvedeliku temp.
• Manufacturer: NRF

• Vehicle Equipment: for vehicles with automatic climate control
• Sensor Type: NTC Sensor
• Colour: blue
• Number of pins: 2
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: MEY

• Transmission Type: Manual Transmission
• Number of pins: 2
• Connector Shape: rectangular
• Supplementary Article/Info 2: without cable
• Name: ANDUR,VAHEMAA
• Manufacturer: MAX
• Lisainfo: 012409191D/MG
• Additional information: 012409191D/MG

• Engine Code: 1Z
• Number of pins: 1
• Thread Size: M10x1
• Spanner Size: 13
• Corresponds to the original part in colour: blue
• Name: ANDUR,OLITEMPERATUUR
• Manufacturer: EPS

• Housing Colour: blue
• Number of pins: 2
• Spanner Size: 0
• Manufacturer: DELPHI
• Name: DE TS10281

• Number of connectors: 2
• Colour: blue
• Weight [kg]: 0.015
• Supplementary Article/Supplementary Info: with gasket/seal, with retaining spring
• Manufacturer: FEBI BILSTEIN

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Engine Code: 1Z
• Manufacturer: FACET

• Number of pins: 2
• Colour: black
• Material: Plastic
• Manufacturer: AIC

General Information: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.

• Number of connectors: 2
• Colour: blue
• Weight [kg]: 0.015
• Supplementary Article/Supplementary Info: with retaining spring, with gasket/seal
• Name: SW 30 93 4762
• Manufacturer: SWAG

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Cable Length [mm]: 521
• Number of pins: 3
• Sensor Type: Inductive Sensor
• Assy./disassy. by qualified personnel required!:
• Manufacturer: ABAKUS LORO

General Information: The following information is for general and informational purposes only and does not constitute warranty terms. Warranty terms and conditions are available from our dealers and in our general terms and conditions of sale. Abakus spare/repair parts are intended only for vehicle repairs in order to restore their original functionality. Abakus spare/repair parts are used or sold to users only for the purpose of repairing vehicles to restore their original look and functionality and are not original/genuine/OE/OEM/OES replacement parts. These items do not originate from the vehicle manufacturer and may be the subject of a design not owned by Abakus and the manufacturer of this spare part. They may only be used for repairs to restore the intended vehicle to its original appearance. Our products are delivered without instruction of installation. Installation of our product may only be carried out by trained specialist technicians in specific car repairs. Products supplied by us are exclusively intended for proper and appropriate use. The warranty may become invalid in the event of: improper installation or repair, unsuitable application or use, installation or repair made outside specialist car workshops. Warranty claims are lost if the vehicle is modified and used for motor sports, tuning or similar events (except our tuning parts which are described in TecDoc and on our price list). Warranty application should include complete documentation among others: chassis no., first registration, vehicle mileage, information about LPG installation, fault memory log, pictures, our QC (quality check) code, installation invoice, contact details of the car repair workshop performing the replacement or repair. Warranty application are available in our Client Panel system. Complaints may require supplementing data such as error memory logs. Incomplete documentation may result in rejection of the claim. Any damage caused during transport is not considered quality damage and will be considered on an individual basis. The product is intended for use within the performance limits specified by the manufacturer and should only be used by qualified personnel who have been trained to operate this product. Before each use, the product should be checked for damage or fixing of its parts and not used if any defects or loose parts are found. Failure to follow the manufacturer's guidelines could result in potential product damage or even injury. Wear appropriate protective clothing if necessary when working with the product.

• Engine Code: AHU
• Number of pins: 4
• Vehicle Identification Number (VIN) from: 8D-Y-000001
• Corresponds to the original part in colour: black
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: EPS

• Engine Code: AHU
• Vehicle Identification Number (VIN) from: 8D-V-000001
• Number of pins: 4
• Vehicle Identification Number (VIN) to: 8D-X-500000
• for article number: 1.660.015K, 1.830.278K, 1.879.946
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: EPS
• Additional information: 1-830-278
• Lisainfo: 1-830-278

• Thread Size: M14x1,5
• Colour: white
• Spanner Size: 19
• Supplementary Article/Supplementary Info: with gasket/seal
• Number of pins: 2
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Engine Code: AHU
• Vehicle Identification Number (VIN) from: 8D-V-000001
• Number of pins: 4
• Vehicle Identification Number (VIN) to: 8D-X-500000
• for article number: 26.0015K, 7.3278K, 7.7946
• Manufacturer: FACET

• Engine Code: AHU
• Number of pins: 4
• Vehicle Identification Number (VIN) from: 8D-Y-000001
• Corresponds to the original part in colour: black
• Manufacturer: FACET

• Thread Size: M20
• Number of pins: 2
• Housing Colour: grey
• Connector Shape: oval
• Manufacturer: ERA

• Thread Size: 20 mm
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: VER

• Length [mm]: 37
• Supplementary Article/Info 2: with seal ring
• for OE number: 025 906 041 A
• Supplementary Article/Supplementary Info: with gasket/seal
• Colour Coding: blue
• Number of pins: 2
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Sensor Type: NTC Sensor
• Voltage [V]: 12
• Colour Coding: blue
• Name: MM SPA106
• Manufacturer: MAGNETI MARELLI

• Engine Code: 1Z
• External Thread Size: M10 x 1
• Number of connectors: 1
• Weight [kg]: 0.01
• Supplementary Article/Info 2: with seal ring
• Manufacturer: FEBI BILSTEIN

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Switch Point [°C]: 125
• Thread Size: 20 mm
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: VER

• Engine Code: 1Z
• Colour: grey
• Number of pins: 3
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: MAX

• Engine Code: AHU
• Vehicle Identification Number (VIN) from: 8D-V-000001
• Number of pins: 4, 2
• Vehicle Identification Number (VIN) to: 8D-X-500000
• Sensor Type: NTC Sensor
• Supplementary Article/Info 2: with seal ring
• Colour: black
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: MEY

• Connector Shape: rectangular
• Number of pins: 2
• Housing material: GRP (Glass fibre Reinforced Plastic), PA 6 GF 30
• Sensor Type: NTC Sensor
• for OE number: 028 906 081
• Manufacturer: TOPRAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• General Information: Intake air temperature sensor
• Manufacturer: VIKA

• Engine Code: 1Z
• External Thread Size: M10 x 1
• Number of connectors: 1
• Weight [kg]: 0.01
• Supplementary Article/Info 2: with seal ring
• Name: SW 30 93 3825
• Manufacturer: SWAG

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Thread Size: M14x1,5
• Number of pins: 2
• Housing Colour: white
• Manufacturer: FAE

• Engine Code: 1Z
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: EPS

• Engine Code: 1Z
• Mounting Type: Plugged
• Voltage [V]: 12
• Resistor [Ohm]: 2,080, 322
• Supplementary Article/Supplementary Info: with gasket/seal
• Temperature range from [°C]: 25
• Temperature range to [°C]: +80
• Colour: blue
• Sensor Type: NTC Sensor
• Number of pins: 2
• Supplementary Article/Info 2: with retaining ring
• Corresponds to the original part in colour: blue
• Assy./disassy. by qualified personnel required!:
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: HEL

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Number of pins: 3
• Temperature range to [°C]: 125
• Manufacturer: ERA

• Fitting Position: Rear
• Fabrication Number: EPDC-AU-020
• Colour: black
• Manufacturer: NTY

• General Information: Transmission speed sensor
• Manufacturer: VIKA

• Vehicle Equipment: for vehicles with automatic climate control
• Guarantee: 3 years guarantee
• Weight [kg]: 0.01
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY

• Number of pins: 2
• Weight [kg]: 0.3
• Packaging length [cm]: 12
• Packaging width [cm]: 8
• Packaging height [cm]: 6

• Fitting Position: Front Axle Left, Front Axle Right
• Fabrication Number: HCA-AU-000
• Manufacturer: NTY

• Number of connectors: 2
• Colour Coding: grey
• Screw length below head [mm]: 20
• Weight [kg]: 0.015
• Supplementary Article/Supplementary Info: with gasket/seal, with retaining spring
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: FEB

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Sensor Type: NTC Sensor
• Mounting Type: Clamped
• Connector Shape: round
• Number of pins: 3
• Temperature range [°C]: 120
• for OE number: 053919501A
• Supplementary Article/Info 2: with seal ring
• Manufacturer: NRF

• Sensor Type: NTC Sensor
• Supplementary Article/Info 2: with Temperature Switch
• Colour: grey
• Number of pins: 3
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: MEY
• Lisainfo: 1009190010
• Additional information: 1009190010

• Fitting Position: Rear Axle Left, Rear Axle Right
• Fabrication Number: HCA-AU-001
• Manufacturer: NTY

• Quantity: 1
• General Information: Coolant temperature sensor
• Manufacturer: VIKA

• Engine Code: 1Z
• Name: EP 1.994.013
• Manufacturer: EPS

• Number of connectors: 2
• Colour Coding: grey
• Screw length below head [mm]: 20
• Weight [kg]: 0.03
• Supplementary Article/Supplementary Info: with gasket/seal, with retaining spring
• Name: SW 30 92 9318
• Manufacturer: SWAG

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Engine Code: 1Z
• Manufacturer: FACET

• Fitting Position: Rear
• Colour: black
• Sensor Type: Ultrasonic Sensor
• Assy./disassy. by qualified personnel required!:
• Manufacturer: ABAKUS LORO

General Information: The following information is for general and informational purposes only and does not constitute warranty terms. Warranty terms and conditions are available from our dealers and in our general terms and conditions of sale. Abakus spare/repair parts are intended only for vehicle repairs in order to restore their original functionality. Abakus spare/repair parts are used or sold to users only for the purpose of repairing vehicles to restore their original look and functionality and are not original/genuine/OE/OEM/OES replacement parts. These items do not originate from the vehicle manufacturer and may be the subject of a design not owned by Abakus and the manufacturer of this spare part. They may only be used for repairs to restore the intended vehicle to its original appearance. Our products are delivered without instruction of installation. Installation of our product may only be carried out by trained specialist technicians in specific car repairs. Products supplied by us are exclusively intended for proper and appropriate use. The warranty may become invalid in the event of: improper installation or repair, unsuitable application or use, installation or repair made outside specialist car workshops. Warranty claims are lost if the vehicle is modified and used for motor sports, tuning or similar events (except our tuning parts which are described in TecDoc and on our price list). Warranty application should include complete documentation among others: chassis no., first registration, vehicle mileage, information about LPG installation, fault memory log, pictures, our QC (quality check) code, installation invoice, contact details of the car repair workshop performing the replacement or repair. Warranty application are available in our Client Panel system. Complaints may require supplementing data such as error memory logs. Incomplete documentation may result in rejection of the claim. Any damage caused during transport is not considered quality damage and will be considered on an individual basis. The product is intended for use within the performance limits specified by the manufacturer and should only be used by qualified personnel who have been trained to operate this product. Before each use, the product should be checked for damage or fixing of its parts and not used if any defects or loose parts are found. Failure to follow the manufacturer's guidelines could result in potential product damage or even injury. Wear appropriate protective clothing if necessary when working with the product.

• Fitting Position: Front Axle
• Cable Length [mm]: 911
• Number of pins: 2
• Sensor Type: Passive sensor
• Assy./disassy. by qualified personnel required!:
• Manufacturer: ABAKUS LORO

General Information: The following information is for general and informational purposes only and does not constitute warranty terms. Warranty terms and conditions are available from our dealers and in our general terms and conditions of sale. Abakus spare/repair parts are intended only for vehicle repairs in order to restore their original functionality. Abakus spare/repair parts are used or sold to users only for the purpose of repairing vehicles to restore their original look and functionality and are not original/genuine/OE/OEM/OES replacement parts. These items do not originate from the vehicle manufacturer and may be the subject of a design not owned by Abakus and the manufacturer of this spare part. They may only be used for repairs to restore the intended vehicle to its original appearance. Our products are delivered without instruction of installation. Installation of our product may only be carried out by trained specialist technicians in specific car repairs. Products supplied by us are exclusively intended for proper and appropriate use. The warranty may become invalid in the event of: improper installation or repair, unsuitable application or use, installation or repair made outside specialist car workshops. Warranty claims are lost if the vehicle is modified and used for motor sports, tuning or similar events (except our tuning parts which are described in TecDoc and on our price list). Warranty application should include complete documentation among others: chassis no., first registration, vehicle mileage, information about LPG installation, fault memory log, pictures, our QC (quality check) code, installation invoice, contact details of the car repair workshop performing the replacement or repair. Warranty application are available in our Client Panel system. Complaints may require supplementing data such as error memory logs. Incomplete documentation may result in rejection of the claim. Any damage caused during transport is not considered quality damage and will be considered on an individual basis. The product is intended for use within the performance limits specified by the manufacturer and should only be used by qualified personnel who have been trained to operate this product. Before each use, the product should be checked for damage or fixing of its parts and not used if any defects or loose parts are found. Failure to follow the manufacturer's guidelines could result in potential product damage or even injury. Wear appropriate protective clothing if necessary when working with the product.

• Fitting Position: Front Axle
• Required quantity: 2
• Manufacturer: DELLO AUTOMEGA

• Transmission Type: 4-Speed Automatic Transmission
• Number of pins: 2
• Name: ANDUR,KIIRUS
• Manufacturer: MAX
• Lisainfo: 095927321C/MG
• Additional information: 095927321C/MG

• Fitting Position: Rear Axle
• Cable Length [mm]: 1,256
• Number of pins: 2
• Sensor Type: Passive sensor
• Assy./disassy. by qualified personnel required!:
• Manufacturer: ABAKUS

General Information: The following information is for general and informational purposes only and does not constitute warranty terms. Warranty terms and conditions are available from our dealers and in our general terms and conditions of sale. Abakus spare/repair parts are intended only for vehicle repairs in order to restore their original functionality. Abakus spare/repair parts are used or sold to users only for the purpose of repairing vehicles to restore their original look and functionality and are not original/genuine/OE/OEM/OES replacement parts. These items do not originate from the vehicle manufacturer and may be the subject of a design not owned by Abakus and the manufacturer of this spare part. They may only be used for repairs to restore the intended vehicle to its original appearance. Our products are delivered without instruction of installation. Installation of our product may only be carried out by trained specialist technicians in specific car repairs. Products supplied by us are exclusively intended for proper and appropriate use. The warranty may become invalid in the event of: improper installation or repair, unsuitable application or use, installation or repair made outside specialist car workshops. Warranty claims are lost if the vehicle is modified and used for motor sports, tuning or similar events (except our tuning parts which are described in TecDoc and on our price list). Warranty application should include complete documentation among others: chassis no., first registration, vehicle mileage, information about LPG installation, fault memory log, pictures, our QC (quality check) code, installation invoice, contact details of the car repair workshop performing the replacement or repair. Warranty application are available in our Client Panel system. Complaints may require supplementing data such as error memory logs. Incomplete documentation may result in rejection of the claim. Any damage caused during transport is not considered quality damage and will be considered on an individual basis. The product is intended for use within the performance limits specified by the manufacturer and should only be used by qualified personnel who have been trained to operate this product. Before each use, the product should be checked for damage or fixing of its parts and not used if any defects or loose parts are found. Failure to follow the manufacturer's guidelines could result in potential product damage or even injury. Wear appropriate protective clothing if necessary when working with the product.

• Fitting Position: Rear Axle
• Required quantity: 2
• Manufacturer: DELLO AUTOMEGA

• Fitting Position: Front Axle
• Sensor Type: Passive sensor
• Cable Length [mm]: 910
• Name: ANDUR, RATTAP™™RETE ARV
• Manufacturer: MAX

• Fitting Position: Front Axle
• Length [mm]: 840
• Number of pins: 2
• Plug Type: Female
• Connector Shape: round
• Voltage [V]: 12
• Weight [kg]: 0.13
• Colour: black
• Operating Mode: Electric
• Always compare old and new part (in particular OE No.):
• Manufacturer: ENERGY

• Fitting Position: Front Axle Left, Front Axle Right
• Sensor Type: Passive sensor
• Manufacturer: JP GROUP
• Lisainfo: Sensor, wheel speed
• Additional information: Sensor, wheel speed

• Fitting Position: Rear
• Voltage [V]: 12
• Shape: straight
• Sensor Type: Ultrasonic Sensor
• Number of pins: 3
• Guarantee: 3 years guarantee
• Weight [kg]: 0.04
• Operating Mode: Electric
• Always compare old and new part (in particular OE No.):
• Name: CE 28SKV033
• Manufacturer: ESEN SKV