• Switch point from [bar]: 0.15
• Switch point to [bar]: 0.35
• Colour Coding: blue
• Number of connectors: 1
• External Thread [mm]: M10x1
• Manufacturer: JP GROUP
• Lisainfo: PAKENDIS 10 tk
• Additional information: PAKENDIS 10 tk

• Switch Pressure [bar]: 1.4
• Number of connectors: 1
• External Thread [mm]: M10x1
• Colour Coding: black
• Manufacturer: JP GROUP
• Lisainfo: PAKENDIS 10 tk
• Additional information: PAKENDIS 10 tk

• Sensor Type: Hall Sensor
• Manufacturer Restriction: BOSCH
• Manufacturer: JP GROUP
• Lisainfo: Hall sender
• Additional information: Hall sender

• Number of pins: 7
• Coil Ignition System: Transistor Ignition (TI)
• Lisainfo: Switch unit for TCI
• Additional information: Switch unit for TCI

• Vehicle Identification Number (VIN) from: 44-J-200 100
• Thread Size: M10x1
• Length [mm]: 46
• Spanner Size: 24
• Number of pins: 1
• Colour: black
• Manufacturer: DELLO AUTOMEGA

• Thread Size: M10x1
• Length [mm]: 46
• Spanner Size: 24
• Colour Coding: white
• Number of pins: 1
• Manufacturer: DELLO AUTOMEGA

• Thread Size: M10x1
• Length [mm]: 46
• Spanner Size: 24
• Colour: blue
• Number of pins: 1
• Manufacturer: DELLO AUTOMEGA

• Plug Type: Blade Terminal
• Operating Mode: Hydraulic
• Colour Coding: blue
• Thread Size: M 10
• Thread Pitch [mm]: 1
• Number of pins: 1
• Control Range [bar]: 0,15 - 0,35
• Manufacturer: TOPRAN
• Lisainfo: 100 345 HP
• Additional information: 100 345 HP

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Vehicle Identification Number (VIN) from: 44-J-200 100
• Thread Size: M10x1
• Colour: grey
• Number of pins: 1
• Spanner Size: 24
• Manufacturer: DELLO AUTOMEGA

• Thread Size: M10
• Colour Coding: brown
• Number of pins: 1
• Switch Pressure [bar]: 0.3
• Spanner Size: 24
• Supplementary Article/Supplementary Info: with seal
• for OE number: 056919081C
• Manufacturer: DELLO AUTOMEGA

• Plug Type: Blade Terminal
• Operating Mode: Hydraulic
• Colour Coding: brown
• Thread Size: M 10
• Thread Pitch [mm]: 1
• Number of pins: 1
• Supplementary Article/Info 2: with seal ring
• Shifting Points [bar]: 0.3
• Manufacturer: TOPRAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Thread Size: M10x1
• Colour: black
• Number of pins: 1
• Spanner Size: 14
• Length [mm]: 25
• Manufacturer: DELLO AUTOMEGA

• Plug Type: Blade Terminal
• Operating Mode: Hydraulic
• Colour Coding: white
• Thread Size: M 10
• Thread Pitch [mm]: 1
• Number of pins: 1
• Control Range [bar]: 1,6 - 2,0
• Supplementary Article/Info 2: with seal ring
• Manufacturer: TOPRAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Switch point from [bar]: 1.6
• Switch point to [bar]: 2
• Manufacturer: JP GROUP
• Lisainfo: PAKENDIS 10 tk
• Additional information: PAKENDIS 10 tk

• Construction Year from: 01.1986
• Plug Type: Blade Terminal
• Operating Mode: Hydraulic
• Colour Coding: black
• Thread Size: M 10
• Thread Pitch [mm]: 1
• Number of pins: 1
• Control Range [bar]: 1,2 - 1,6
• Supplementary Article/Info 2: with seal ring
• Manufacturer: TOPRAN HANS PRIES

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Colour: black
• Supplementary Article/Supplementary Info: with seal
• Lisainfo: Sender for oil temperature
• Additional information: Sender for oil temperature

• Length [mm]: 46
• Thread Size: M10x1
• Spanner Size: 24
• Colour Coding: white
• Number of pins: 1
• Pressure [bar]: 1.8
• Name: OLISURVELšLITUS
• Manufacturer: MAX

• Construction Year from: 01.1987
• Length [mm]: 46
• Thread Size: M10x1
• Spanner Size: 24
• Colour Coding: grey
• Number of pins: 1
• Pressure from [bar]: 0.75
• Pressure to [bar]: 1.05
• Diameter [mm]: 2
• Name: OLISURVELšLITUS
• Manufacturer: MAX

• Length [mm]: 46
• Spanner Size: 24
• Colour Coding: blue
• Number of pins: 1
• Thread Size: M10x1
• Pressure from [bar]: 0.15
• Pressure to [bar]: 0.35
• Diameter [mm]: 3
• Name: OLISURVELšLITUS
• Manufacturer: MAX

• Length [mm]: 46
• Thread Size: M10x1
• Spanner Size: 24
• Colour Coding: black
• Pressure from [bar]: 1.2
• Pressure to [bar]: 1.5
• Diameter [mm]: 3
• Name: OLISURVELšLITUS
• Manufacturer: MAX

• Quantity: 1
• Colour Coding: white
• Supplementary Article/Info 2: with seal ring
• Surface: Zinc-coated
• Length [mm]: 46
• Weight [kg]: 0.03
• Required quantity: 1
• External Thread [mm]: M10 x 1
• Spanner Size: 24
• Number of connectors: 1
• Thread Length [mm]: 13
• Switch point from [bar]: 1.6
• Switch point to [bar]: 2
• General Information: oil pressure switch
• Manufacturer: VIKA

• Number of connectors: 2
• Switch Point [°C]: 30
• Colour Coding: red
• Manufacturer: JP GROUP
• Lisainfo: Thermo switch for cooling system, 45/17 C
• Additional information: Thermo switch for cooling system, 45/17 C

• Construction Year from: 01.1987
• Switch point from [bar]: 0.75
• Switch point to [bar]: 1.05
• External Thread [mm]: M10x1
• Number of connectors: 1
• Colour Coding: grey
• Lisainfo: PAKENDIS 10 tk
• Additional information: PAKENDIS 10 tk

• Switch point from [bar]: 0.15
• Length [mm]: 46
• Switch point to [bar]: 0.35
• Inner Diameter [mm]: 2.54
• External Thread Size: M10 x 1
• Thread Length [mm]: 13
• Spanner Size: 24
• Number of connectors: 1
• Colour Coding: blue
• Surface: Zinc-coated
• Weight [kg]: 0.031
• Supplementary Article/Info 2: with seal ring
• Name: OLISURVELšLITUS
• Manufacturer: FEB

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Thread Size: M 10x1
• Housing Colour: black
• Pressure [bar]: 0.4
• Manufacturer: FAE

• Switch point from [bar]: 0.15
• Length [mm]: 46
• Switch point to [bar]: 0.35
• Inner Diameter [mm]: 2.54
• External Thread Size: M10 x 1
• Thread Length [mm]: 13
• Spanner Size: 24
• Number of connectors: 1
• Colour Coding: blue
• Surface: Zinc-coated
• Weight [kg]: 0.031
• Supplementary Article/Info 2: with seal ring
• Manufacturer: SWAG
• Name: SW 30 23 0002

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Thread Size: M10x1,0
• Colour: black
• Number of connectors: 1
• Weight [kg]: 0.019
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Quantity: 1
• Supplementary Article/Info 2: with seal ring
• Surface: Zinc-coated
• Colour Coding: blue
• Length [mm]: 46
• Weight [kg]: 0.031
• Required quantity: 1
• Control Range [bar]: 0,15 - 0,35
• External Thread [mm]: M10 x 1
• Spanner Size: 24
• Inner Diameter [mm]: 2.54
• Number of connectors: 1
• Thread Length [mm]: 13
• General Information: oil pressure switch
• Manufacturer: VIKA

• Pressure [bar]: 3.5
• Housing Colour: blue
• Thread Size: M10×1-6g
• Diameter [mm]: 24
• Spanner Size: 24
• Number of pins: 1
• Manufacturer: DELPHI
• Name: DE SW90009
• Lisainfo: SW90009
• Additional information: SW90009

• Manufacturer: FAE
• Additional information: NRF32110
• Lisainfo: NRF32110

• Pressure [bar]: 1.8
• Thread Size: M10 x 1
• Number of pins: 1
• Technical Information Number: circuit N.O.
• Manufacturer: ERA

• Sensor Type: NTC Sensor
• Mounting Type: Bolted
• Connector Shape: round
• Number of pins: 1
• Spanner Size: 14
• Thread Size: M10x1
• for OE number: 027919501
• Supplementary Article/Info 2: with seal ring
• Name: Andur,Jahutusvedeliku temp.
• Manufacturer: NRF

• Switch point from [bar]: 1.6
• Length [mm]: 46
• Switch point to [bar]: 2
• External Thread Size: M10 x 1
• Thread Length [mm]: 13
• Spanner Size: 24
• Number of connectors: 1
• Colour Coding: white
• Surface: Zinc-coated
• Weight [kg]: 0.03
• Supplementary Article/Info 2: with seal ring
• Manufacturer: SWAG
• Name: SW 30 23 0001

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Length [mm]: 25
• Temperature range to [°C]: 125
• External Thread Size: M10 x 1
• Thread Length [mm]: 10.9
• Spanner Size: 14
• Number of connectors: 1
• Colour Coding: black
• Weight [kg]: 0.012
• Supplementary Article/Info 2: with seal ring
• Manufacturer: FEBI

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Pressure [bar]: 0.3
• Thread Size: M10 x 1
• Technical Information Number: circuit N.C.
• Manufacturer: ERA

• Required quantity: 1
• Construction Year from: 01.1987
• Colour: grey
• Pressure [bar]: 0.9
• Manufacturer: AIC

General Information: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.

• Colour: black
• Pressure [bar]: 1.4
• Manufacturer: AIC

General Information: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.

• Thread Size: M 10x1
• Housing Colour: white
• Pressure [bar]: 1.8
• Manufacturer: FAE

• Engine Code: KP
• Pressure [bar]: 2
• Thread Size: M10x1
• Spanner Size: 24
• Name: OLISURVELšLITUS
• Manufacturer: EPS

• Colour: blue
• Shifting Points [bar]: 0.25
• Manufacturer: AIC

General Information: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.

• Colour: white
• Pressure [bar]: 1.8
• Manufacturer: AIC

General Information: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.

• Pressure [bar]: 0.25
• Thread Size: M10 x 1
• Technical Information Number: circuit N.C.
• Manufacturer: ERA

• Supplementary Article/Supplementary Info: with seal
• Thread Size: M10x1,0
• Control Range [bar]: 0,15 - 0,35
• Colour: blue
• Weight [kg]: 0.038
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Thread Size: M 10x1
• Colour: brown
• Spanner Size: 24
• Number of pins: 1
• Supplementary Article/Info 2: with seal ring
• Pressure [bar]: 0.25
• Manufacturer: AIC

General Information: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.

• Temperature range to [°C]: 125
• Length [mm]: 25
• External Thread Size: M10 x 1
• Thread Length [mm]: 10.9
• Spanner Size: 14
• Number of connectors: 1
• Colour Coding: black
• Weight [kg]: 0.012
• Supplementary Article/Info 2: with seal ring
• Name: SW 99 90 1939
• Manufacturer: SWAG

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Construction Year from: 08.1986
• Pressure [bar]: 10.5
• Housing Colour: grey
• Thread Size: M10×1-6g
• Diameter [mm]: 24
• Spanner Size: 24
• Number of pins: 1
• Name: OLISURVELšLITUS
• Manufacturer: DLP
• Lisainfo: SW90007
• Additional information: SW90007

• Construction Year from: 01.1987
• Thread Size: M10x1,0
• Colour: white
• Weight [kg]: 0.031
• Pressure from [bar]: 0.7
• Pressure to [bar]: 1
• Manufacturer: VEMO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Switch point from [bar]: 1.2
• Length [mm]: 46
• Switch point to [bar]: 1.5
• Inner Diameter [mm]: 2.54
• External Thread Size: M10 x 1
• Thread Length [mm]: 13
• Spanner Size: 24
• Colour Coding: black
• Surface: Zinc-coated
• Weight [kg]: 0.031
• Supplementary Article/Info 2: with seal ring
• Name: SW 30 23 0003
• Manufacturer: SWAG

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Pressure [bar]: 16
• Housing Colour: black
• Thread Size: M10×1-6g
• Diameter [mm]: 24
• Spanner Size: 24
• Number of pins: 1
• Manufacturer: DELPHI
• Name: DE SW90005
• Lisainfo: SW90005
• Additional information: SW90005

• Construction Year from: 01.1986
• Plug Type: Blade Terminal
• Operating Mode: Hydraulic
• Colour Coding: grey
• Thread Size: M 10
• Thread Pitch [mm]: 1
• Number of pins: 1
• Control Range [bar]: 0,75 - 1,05
• Supplementary Article/Info 2: with seal ring
• Manufacturer: TOPRAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Length [mm]: 46
• Switch point from [bar]: 1.6
• Switch point to [bar]: 2
• External Thread Size: M10 x 1
• Thread Length [mm]: 13
• Spanner Size: 24
• Number of connectors: 1
• Colour Coding: white
• Surface: Zinc-coated
• Weight [kg]: 0.03
• Supplementary Article/Info 2: with seal ring
• Name: OLISURVELšLITUS
• Manufacturer: FEB

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Switch point from [bar]: 1.2
• Length [mm]: 46
• Switch point to [bar]: 1.5
• Inner Diameter [mm]: 2.54
• External Thread Size: M10 x 1
• Thread Length [mm]: 13
• Spanner Size: 24
• Colour Coding: black
• Surface: Zinc-coated
• Weight [kg]: 0.031
• Supplementary Article/Info 2: with seal ring
• Name: OLISURVELšLITUS
• Manufacturer: FEB

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Thread Size: M10x1,0
• Control Range [bar]: 1,2 - 1,6
• Colour: black
• Weight [kg]: 0.028
• Manufacturer: VEMO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Pressure from [bar]: 0.15
• Pressure to [bar]: 0.35
• Combi Switch Function: Normally Closed Contact
• Colour: blue
• Spanner Size: 24
• Thread Size: M10 x 1,0
• Number of pins: 1
• Name: OLISURVELšLITUS
• Manufacturer: MEY

• Thread Size: M10x1.0
• Manufacturer: VERNET

• Construction Year from: 01.1987
• Switch point from [bar]: 0.75
• Length [mm]: 46
• Switch point to [bar]: 1.05
• Inner Diameter [mm]: 2.48
• External Thread Size: M10 x 1
• Thread Length [mm]: 13
• Spanner Size: 24
• Number of connectors: 1
• Colour Coding: grey
• Surface: Zinc-coated
• Weight [kg]: 0.031
• Supplementary Article/Info 2: with seal ring
• Manufacturer: SWAG
• Name: SW 30 23 0004

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Pressure from [bar]: 1.6
• Pressure to [bar]: 2
• Combi Switch Function: Normally Open Contact
• Colour: white
• Supplementary Article/Supplementary Info: with seal
• Spanner Size: 24
• Thread Size: M10 x 1,0
• Number of pins: 1
• Name: OLISURVELšLITUS
• Manufacturer: MEY

• Construction Year from: 01.1987
• Length [mm]: 46
• Switch point from [bar]: 0.75
• Switch point to [bar]: 1.05
• Inner Diameter [mm]: 2.48
• External Thread Size: M10 x 1
• Thread Length [mm]: 13
• Spanner Size: 24
• Number of connectors: 1
• Colour Coding: grey
• Surface: Zinc-coated
• Weight [kg]: 0.031
• Supplementary Article/Info 2: with seal ring
• Name: OLISURVELšLITUS
• Manufacturer: FEB

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Voltage [V]: 12
• Combi Switch Function: Normally Closed Contact
• Current Strength [A]: 0.25
• Thread Size: M10x1
• Spanner Size: 24
• Pressure from [bar]: 0.15
• Pressure to [bar]: 0.35
• Number of pins: 1
• Plug Type: Blade Terminal
• Corresponds to the original part in colour: blue
• Assy./disassy. by qualified personnel required!:
• SVHC: 7439-92-1; Lead
• Name: Olisurvellitus
• Manufacturer: HEL

• Construction Year to: 07.1986
• Number of pins: 2
• Manufacturer: JP GROUP
• Lisainfo: Sender for water temperature gauge 2 pins
• Additional information: Sender for water temperature gauge 2 pins

• Pressure [bar]: 20
• Housing Colour: white
• Thread Size: M10×1-6g
• Diameter [mm]: 24
• Spanner Size: 24
• Number of pins: 1
• Manufacturer: DELPHI
• Name: DE SW90060

• Temperature range to [°C]: 125
• External Thread [mm]: M10 x 1
• Supplementary Article/Info 2: with seal ring
• Manufacturer: AIC

General Information: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.

• Colour: black
• Number of pins: 1
• Weight [kg]: 0.3
• Packaging length [cm]: 12
• Packaging width [cm]: 8
• Packaging height [cm]: 6

• Plug Type: Blade Terminal
• Thread Size: M 10 x 1,0 mm
• Number of pins: 2
• Temperature range from [°C]: 25
• Temperature range to [°C]: 17
• Colour Coding: black
• Manufacturer: TOPRAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Construction Year to: 07.1986
• Colour Coding: white
• Thread Size: M 10
• Thread Pitch [mm]: 1
• Connector Shape: angular
• Number of pins: 2
• Temperature range to [°C]: 120
• Manufacturer: TOPRAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Plug Type: Blade Terminal
• Thread Size: M 10
• Number of pins: 2
• Temperature range from [°C]: 30
• Temperature range to [°C]: 40
• Colour Coding: red
• Housing Colour: grey
• Manufacturer: TOPRAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Observe technical data:
• Manufacturer: BOSCH

• Number of connectors: 2
• Colour Coding: grey
• Screw length below head [mm]: 20
• Weight [kg]: 0.015
• Supplementary Article/Supplementary Info: with seal, with retaining spring
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: FEB

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• for OE number: 0269061612
• Name: Andur,Jahutusvedeliku temp.
• Manufacturer: NRF

• Thread Size: M10 x 1
• Number of pins: 2
• Manufacturer: ERA

• Number of connectors: 2
• Colour Coding: grey
• Screw length below head [mm]: 20
• Weight [kg]: 0.03
• Supplementary Article/Supplementary Info: with retaining spring, with seal
• Manufacturer: SWAG

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Engine Code: KP
• Lambda Sensor: Regulating Probe, Unheated
• Number of circuits: 1
• Name: LAMBDA ANDUR
• Manufacturer: MAX

• Lambda Sensor: Unheated, Regulating Probe
• Number of pins: 1
• Fitting Position: Exhaust Manifold
• for article number: 81000
• Manufacturer: MEAT&DORIA

• Engine Code: KP
• Lambda Sensor: Regulating Probe, Thread pre-greased
• Length [mm]: 470
• Number of circuits: 1
• Weight [kg]: 0.108
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Lambda Sensor: Regulating Probe, Unheated
• Voltage [V]: 12
• Length [mm]: 500
• Number of circuits: 1
• Weight [kg]: 0.12
• Operating Mode: Electric
• Warranty: 3 years warranty
• Always compare old and new part (in particular OE No.):
• Name: CE 09SKV522
• Manufacturer: ESEN SKV

• Exhaust System: for pre-catalytic converter
• Quality: OE
• Manufacturer Restriction: DENSO
• Thread Size: M18x1.5
• Cable Length [mm]: 300
• Number of pins: 1
• Weight [g]: 74
• Gross Weight [g]: 118
• Manufacturer: DENSO

Lambda Sensor: Regulating Probe, Unheated, Finger probe, Lambda Sensor

• Lambda Sensor: Lambda Sensor
• Cable Length [mm]: 500
• Number of circuits: 1
• Manufacturer: ERA

• Construction Year from: 01.1985
• Switch Point [°C]: 118
• Colour: brown
• Number of pins: 3
• Supplementary Article/Supplementary Info: with seal
• Manufacturer: METZGER

• Lambda Sensor: Regulating Probe
• Fitting Position: before catalytic converter
• Number of circuits: 1
• Recommended change interval [km]: 80,000
• Connector/Clamp: Connector may need adjustment
• Name: LAMBDA ANDUR
• Manufacturer: BOS

• Lambda Sensor: Regulating Probe
• Fitting Position: before catalytic converter
• Number of circuits: 1
• Overall Length [mm]: 500
• Available as universal article as well, see article no.: 0258986501
• Recommended change interval [km]: 50,000
• Name: LAMBDA ANDUR
• Manufacturer: BOS