• Housing Colour: green
• Spanner Size: 19
• for OE number: 13 62 2 242 184
• Manufacturer: KAMOKA

• Housing Colour: brown
• Spanner Size: 19
• Manufacturer: KAMOKA

• for RPO number up to: 07727
• Connector Shape: rectangular
• Sensor Type: NTC Sensor
• Number of pins: 2
• Thread Size: M 12
• Thread Pitch [mm]: 1.5
• for OE number: 1920 K9, 9613147080
• Manufacturer: TOPRAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Engine Code: HDZ (TU1M)
• Housing Colour: yellow
• Thread Size: M12x1,5
• Spanner Size: 19
• Number of pins: 2
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: MAX

• Colour: brown
• Number of pins: 2
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: MAX

• Number of pins: 2
• Housing Colour: green
• Colour Coding: yellow
• Supplementary Article/Info 2: with seal ring
• Weight [kg]: 0.02
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• for RPO number up to: 07727
• Spanner Size: 19
• Colour Coding: green
• Number of pins: 2
• Thread Size: M12x1,5
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: MAX

• Vehicle Equipment: for vehicles with air conditioning
• Connector Shape: rectangular
• Colour Coding: brown
• Sensor Type: PTC
• Number of pins: 2
• Thread Size: M 14, 1,25
• Manufacturer: TOPRAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• OE-numbri jaoks: 1920.AW
• Pikkus (mm): 17
• Seerianumber: ECP-CT-002
• Manufacturer: NTY

• for RPO number from: 07728
• Connector Shape: rectangular
• Sensor Type: NTC Sensor
• Thread Size: M 12
• Thread Pitch [mm]: 1.5
• Number of pins: 2
• for OE number: 13 38 454, 1362 2 242 184, 1920 3F, 90487859
• Manufacturer: TOPRAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Thread Size: M12x1.5
• Manufacturer: VERNET

• Number of pins: 3
• Name: ANDUR,KIIRUS
• Manufacturer: MAX
• Lisainfo: 6160.70/MG
• Additional information: 6160.70/MG

Seerianumber: ECP-CT-018

• OE-numbri jaoks: 9639381480
• Pistikkontaktide arv: 4
• Piirangutega toode/piirangu info 2: koos integreeritud õhutemp.anduriga
• Surve alates [kPA]: 10
• Surve kuni [kPA]: 117
• Seerianumber: ECM-PE-000
• Manufacturer: NTY
• Name: NTY ECM-PE-000

• Engine Code: HDZ (TU1M)
• Connector Shape: rectangular
• Material: Plastic
• Number of pins: 2
• Plug Type: Female
• Sensor Type: NTC Sensor
• Spanner Size: S19
• Thread Size: M12*1,5
• Manufacturer: NISSENS

Technical Information: FIRST FIT - a time-saving installation! Find all additional parts such as O-rings, clip, washer in the box.

• Engine Code: TU1M+
• Sensor Type: NTC Sensor
• Mounting Type: Bolted
• Connector Shape: rectangular
• Number of pins: 2
• Spanner Size: 19
• Thread Size: M12x1.5
• for OE number: 6081220
• Supplementary Article/Info 2: with seal ring
• Name: Andur,Jahutusvedeliku temp.
• Manufacturer: NRF

• Sensor Type: Passive sensor
• for OE number: 1920 AW
• Manufacturer: KAMOKA

• Thread Size: M14 x 1,5
• Number of pins: 2
• Colour Coding: brown
• Weight [kg]: 0.038
• Manufacturer: VEMO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Engine Code: TU1M+
• Housing Colour: blue
• Number of pins: 2
• Thread Size: M12X1.5-6g
• Spanner Size: 19
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: DLP

• for RPO number up to: 07727
• External Thread Size: M12 x 1,5
• Spanner Size: 19
• Number of connectors: 2
• Colour Coding: green
• Weight [kg]: 0.022
• Supplementary Article/Info 2: with seal ring
• Manufacturer: BLUEPRINT

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Connector Shape: rectangular
• Number of pins: 3
• Supplementary Article/Info 2: with seal ring
• for OE number: 6160 70
• Manufacturer: TOPRAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• for RPO number up to: 07727
• External Thread Size: M12 x 1,5
• Spanner Size: 19
• Number of connectors: 2
• Colour Coding: green
• Weight [kg]: 0.025
• Supplementary Article/Info 2: with seal ring
• Manufacturer: FEBI BILSTEIN

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• for RPO number up to: 07727
• External Thread Size: M12 x 1,5
• Spanner Size: 19
• Number of connectors: 2
• Colour Coding: green
• Weight [kg]: 0.025
• Supplementary Article/Info 2: with seal ring
• Manufacturer: SWAG
• Name: SW 62 91 8991

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Number of connectors: 2
• Colour: brown
• Weight [kg]: 0.033
• Name: SW 62 10 6458
• Manufacturer: SWAG

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Number of connectors: 2
• Colour: brown
• Weight [kg]: 0.033
• Manufacturer: FEBI BILSTEIN

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Piduriliik: Trummelpidur
• Installatsiooni pool: Tagasild vasakul, Tagasild paremal
• Seerianumber: HCA-CT-010
• Manufacturer: NTY

• Height [mm]: 17.2
• Resistor [Ohm]: 550
• Number of connectors: 2
• Manufacturer: VERNET

• Fitting Position: Rear Axle
• pikkus üle kõige (mm): 810
• Pikkus (mm): 40
• Anduritüüp: passiivne andur
• Pistiku värv: sinine
• Kaablipikkus (mm): 687
• paaris tootenumbrid: 30395
• Kaal (kg): 0,14
• Manufacturer: A.B.S.

• Installatsiooni pool: esisild vasakul, esisild paremal
• Seerianumber: HCA-CT-009
• Manufacturer: NTY

• Engine Code: TU1M+
• Mounting Type: Bolted
• Voltage [V]: 12
• Resistor [Ohm]: 2,080, 291
• Supplementary Article/Supplementary Info: with seal
• Temperature range from [°C]: 25
• Temperature range to [°C]: 80
• Thread Size: M12x1,5
• Colour: green
• Sensor Type: NTC Sensor
• Number of pins: 2
• Colour Coding: yellow
• Corresponds to the original part in colour: green
• Assy./disassy. by qualified personnel required!:
• Name: HE 6PT009107431
• Manufacturer: HELLA

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• for RPO number from: 07756, 07728
• Emission Standard: IFL4
• Connector Shape: rectangular
• Number of pins: 2
• Supplementary Article/Info 2: without cable
• Manufacturer: TOPRAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Number of pins: 2
• Weight [kg]: 0.3
• Packaging length [cm]: 12
• Packaging width [cm]: 8
• Packaging height [cm]: 6

• Required quantity: 1
• Pistikkontaktide arv: 2
• Anduritüüp: Induktiivandur
• Piirangutega toode/piirangu info 2: ilma kaablita
• Korpusevärv: must
• Manufacturer: BRM

Name: CZUJNIK POO½ENIA WAU KORB. CITROEN BERLINGO 1,1 96-

• Värv: must
• valikuliselt:
• Pistikkontaktide arv: 2
• Piirangutega toode/piirangu info 2: ilma kaablita
• Pistikukatte kuju: ristkülik
• Kaal (kg): 0,064
• Takistus [oom]: 450
• alternatiivne remondikomplekt: 550015
• Installatsiooni sügavus (mm): 17
• Manufacturer: ERA

• Number of pins: 2
• Manufacturer: DELPHI

• Engine Code: HDZ (TU1M), TU1M+
• Housing Colour: yellow
• Keermemõõt: M12x1,5
• Võtmekaugus: 19
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: EPS

tootekoodile: 1.880.117, 1.880.119, 1.880.120, 1.880.121, 1.880.122, 1.880.142, 1.880.149, 1.880.150, 1.880.158, 1.880.193

• Height [mm]: 39
• Supplementary Article/Info 2: for crankshaft, without cable
• Fitting Position: Flywheel side
• Required quantity: 1
• Resistor [Ohm]: 500
• Colour: black
• Sensor Type: Inductive Sensor, Passive sensor
• Number of pins: 2
• Number of connectors: 2
• Rated Voltage [V]: 12
• Connector Shape: rectangular
• Weight [kg]: 0.125
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Fitting Position: Rear Axle
• Quantity: 2
• Net weight [kg]: 0.1
• Name: ANDUR, RATTAP™™RETE ARV
• Manufacturer: NK

• Engine Code: HDZ (TU1M)
• Manufacturer Restriction: SIEMENS
• Name: ANDUR, VŽNTVOLL
• Manufacturer: EPS

• Sensor Type: Passive sensor
• Number of pins: 2
• Cable Length [mm]: 687
• Fitting Position: Rear Axle Right, Rear Axle Left
• Manufacturer: AUTOFREN SEINSA
• Name: SE DS0167

• Spanner Size: 19
• Thread Size: 12x1.5
• Number of pins: 2
• Supplementary Article/Info 2: with seal ring
• Weight [kg]: 0.03
• Name: VA 700022
• Manufacturer: VALEO

• Voltage [V]: 12
• Resistor [Ohm]: 550
• Colour: black
• Sensor Type: Inductive Sensor
• Number of pins: 2
• Supplementary Article/Info 2: without cable
• Fitting Position: Flywheel side
• Assy./disassy. by qualified personnel required!:
• Manufacturer: HELLA
• Name: HE 6PU009163461

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Required quantity: 1
• Manufacturer: BREMI

• Transmission Type: not for automatic transmission
• for RPO number from: 07728
• Length [mm]: 17
• Number of connectors: 2
• Weight [kg]: 0.06
• Manufacturer: FEBI

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• for RPO number from: 7728
• Manufacturer: BOSCH

• Check OE number:
• Sensor Type: Inductive Sensor
• Number of pins: 2
• Name: ANDUR, VŽNTVOLL
• Manufacturer: MEY

• Fitting Position: Front Axle
• Required quantity: 2
• Cable Length [mm]: 590
• Name: ANDUR, RATTAP™™RETE ARV
• Manufacturer: TRI

• Transmission Type: not for automatic transmission
• for RPO number from: 07728
• Length [mm]: 7
• Number of connectors: 2
• Weight [kg]: 0.06
• Name: SW 62 93 1241
• Manufacturer: SWAG

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Fitting Position: Front Axle
• Quantity: 2
• Sensor Type: Passive sensor
• Number of occupied pins: 2
• Cable Length [mm]: 545
• Manufacturer: DELPHI LOCKHEED HAMULCE
• Name: DE SS20047

• Fitting Position: Rear Axle
• pikkus üle kõige (mm): 800
• Pikkus (mm): 30
• Anduritüüp: passiivne andur
• Pistiku värv: sinine
• Kaablipikkus (mm): 700
• paaris tootenumbrid: 30397
• Kaal (kg): 0,14
• Manufacturer: A.B.S.

• Lambda andur: Sond, Keere eelmääritud
• Ühendus/klemm: vajadusel kohandada pistikühendus
• Ülekandeliinide arv: 4
• Installatsiooni pool: katalüsaatori ees
• Seerianumber: ESL-UV-000
• Manufacturer: NTY

• Fitting Position: Rear Axle
• Required quantity: 2
• Cable Length [mm]: 743
• Fitting Depth [mm]: 29.9
• Number of pins: 2
• Name: ANDUR, RATTAP™™RETE ARV
• Manufacturer: TRI

• Braking/Drive Dynamics: for vehicles with ABS
• Fitting Position: Right, Left, Front Axle
• Cable Length [mm]: 550
• Manufacturer: SNR /NTN-SNR/
• Name: SN ASB159.27

• for RPO number from: 7728
• Manufacturer: BOSCH

• Engine Code: TU1M+
• Weight [kg]: 0.05
• Manufacturer: VALEO

• Number of circuits: 4
• Lambda Sensor: Regulating Probe
• Manufacturer: KAMOKA

• Lambda andur: Diagnoosisond, Keere eelmääritud
• Seerianumber: ESL-SK-000
• Manufacturer: NTY
• Name: NTY ESL-SK-000

• Fitting Position: Rear Axle
• Quantity: 2
• Sensor Type: Passive sensor
• Number of occupied pins: 2
• Cable Length [mm]: 710
• Manufacturer: DELPHI

• Fitting Position: Right, Rear Axle
• Cable Length [mm]: 775
• Manufacturer: SNR /NTN-SNR/

• Fitting Position: Rear Axle
• Required quantity: 2
• Cable Length [mm]: 720
• Fitting Depth [mm]: 41.5
• Name: ANDUR, RATTAP™™RETE ARV
• Manufacturer: TRI

• Fitting Position: before catalytic converter
• Lambda Sensor: Regulating Probe, Planar probe
• Emission Standard: 15-04
• Number of pins: 4
• Length [mm]: 445
• Manufacturer: TOPRAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Manufacturer Restriction: Citroen, Peugeot, Renault
• Number of pins: 4
• Cable Length [mm]: 200
• Supplementary Article/Supplementary Info: with socket housing
• Supplementary Article/Info 2: with pipe
• Cable cross-section from [mm²]: 0.75
• Cable cross-section to [mm²]: 1.5
• Cable insulation material: Silicone
• Temperature range from [°C]: -25
• Temperature range to [°C]: +140
• for OE number: 9639381480
• Plug housing design: Plug sleeve housing
• SVHC: No SVHC present!
• Name: Kaabli remondikomplekt,
• Manufacturer: HBE

• Number of pins: 4
• Pressure from [kPA]: 14
• Name: ANDUR,OHUVOTU ROHK
• Manufacturer: DLP
• Additional information: PS10128 DEL
• Lisainfo: PS10128 DEL

• Number of connectors: 3
• Weight [kg]: 0.04
• Supplementary Article/Info 2: with seal ring
• Name: SW 62 93 8684
• Manufacturer: SWAG

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Transmission Code: MA / MA S, BVA MB3
• Number of pins: 3
• Connector Shape: rectangular
• Weight [kg]: 0.04
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Name: ANDUR,OHUVOTU ROHK
• Manufacturer: BOS

• Fitting Position: Rear Axle
• Quantity: 2
• Sensor Type: Passive sensor
• Number of occupied pins: 2
• Cable Length [mm]: 695
• Manufacturer: DELPHI LOCKHEED HAMULCE
• Name: DE SS20297

• Braking/Drive Dynamics: for vehicles with ABS
• Fitting Position: Right, Left, Rear Axle
• Cable Length [mm]: 790
• Manufacturer: SNR /NTN-SNR/
• Name: SN ASB159.26

• Weight [kg]: 0.05
• Name: ANDUR,KIIRUS
• Manufacturer: VAL

• Lambda Sensor: Regulating Probe, Heated
• Fitting Position: before catalytic converter
• Block Separation:
• for manufacturer exhaust norm: EURO93-CEE19.5
• Number of circuits: 4
• Connector/Clamp: Connector may need adjustment
• Name: LAMBDA ANDUR
• Manufacturer: MAX

• Engine Code: HDZ (TU1M)
• Emission Standard: Euro 2
• Lambda Sensor: Regulating Probe
• Ülekandeliinide arv: 4
• Piirangutega toode/piirangu info 2: ilma pistikuta
• Manufacturer: ENERGY

• Engine Code: HDZ (TU1M)
• Surve alates [kPA]: 10
• Surve kuni [kPA]: 117
• Väljundpinge alates [V]: 0,405
• Väljundpinge kuni [V]: 4,75
• Manufacturer: EPS

• Fitting Position: Front Axle
• Sensor Type: Passive sensor
• Supplementary Article/Info 2: with cable
• Overall Length [mm]: 575
• Temperature range from [°C]: -40
• Temperature range to [°C]: 150
• Name: ANDUR, RATTAP™™RETE ARV
• Manufacturer: BOS

• Required quantity: 2
• Fitting Position: Front Axle
• Pikkus (mm): 515
• MAPP-code olemas:
• Manufacturer: ATE

• Number of pins: 4
• Mounting Type: Bolted
• Assy./disassy. by qualified personnel required!:
• SVHC: 7439-92-1; Lead
• Name: HE 6PP009400301
• Manufacturer: HELLA

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Lambda Sensor: Regulating Probe, Planar probe, Heated
• Emission Standard: Euro 1
• Fitting Position: before catalytic converter
• Alternatively:
• Cable Length [mm]: 400
• Name: LAMBDA ANDUR
• Manufacturer: DLP

• Lambda Sensor: Regulating Probe, Planar probe, Heated
• Emission Standard: Euro 2
• Fitting Position: before catalytic converter
• Cable Length [mm]: 525
• Name: LAMBDA ANDUR
• Manufacturer: DLP
• Quality class: PJ

Additional information: "Tootja: DELPHI
406 (8B), 10.95-05.0
(kvaliteediklass: PJ)" Lisainfo: "Tootja: DELPHI
406 (8B), 10.95-05.0
(kvaliteediklass: PJ)"

• Lambda Sensor: Regulating Probe, Planar probe, Heated
• Emission Standard: Euro 1
• Fitting Position: before catalytic converter
• Cable Length [mm]: 400
• Manufacturer: DELPHI
• Name: DE ES20272-12B1

• Lambda Sensor: Regulating Probe, Planar probe, Heated
• Emission Standard: Euro 2
• Fitting Position: before catalytic converter
• Cable Length [mm]: 380
• Name: LAMBDA ANDUR
• Manufacturer: DLP

• Exhaust System: for pre-catalytic converter
• Quality: OE
• Manufacturer Restriction: DENSO
• Thread Size: M18x1.5
• Cable Length [mm]: 750
• Number of pins: 4
• Weight [g]: 100
• Gross Weight [g]: 149
• Manufacturer: DENSO
• Name: DN DOX-0120
• Quality class: Q

Lambda Sensor: Regulating Probe, Heated, Finger probe, Lambda Sensor Additional information: "Tootja: DENSO
164 (164), 01.87-09.
(kvaliteediklass: Q)" Lisainfo: "Tootja: DENSO
164 (164), 01.87-09.
(kvaliteediklass: Q)"

• Lambda Sensor: Regulating Probe, Planar probe, Heated
• Emission Standard: Euro 2
• Fitting Position: before catalytic converter
• Cable Length [mm]: 630
• Manufacturer: DELPHI
• Name: DE ES20234-12B1

• Lambda Sensor: Regulating Probe, Planar probe, Heated
• Emission Standard: Euro 2
• Fitting Position: before catalytic converter
• Cable Length [mm]: 530
• Name: LAMBDA ANDUR
• Manufacturer: DLP

• Lambda Sensor: Regulating Probe
• Fitting Position: before catalytic converter
• Emission Standard: 15-04, CEE 19-5, CEE 95 L3
• Block Separation:
• Number of circuits: 4
• Recommended change interval [km]: 160,000
• Connector/Clamp: Connector may need adjustment
• Name: LAMBDA ANDUR
• Manufacturer: BOS

• for OE number: 16289W, 16287S
• Exhaust System: for pre-catalytic converter
• Quality: OE
• Manufacturer Restriction: DENSO
• Thread Size: M18x1.5
• Cable Length [mm]: 540
• Number of pins: 4
• Weight [g]: 103
• Gross Weight [g]: 133
• Manufacturer: DENSO
• Name: DN DOX-1535

Lambda Sensor: Regulating Probe, Heated, Finger probe, Lambda Sensor

• Line insulation design: with silicone-coated woven-fibre insulation
• Connector Shape: round
• Conductor Number: 4
• Cable Length [mm]: 450
• Thread Size: M18 x 1,5
• Length [mm]: 570
• Version: ZR-PLANAR
• Weight [kg]: 0.143
• Lambda Sensor: Thread pre-greased
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.