• Number of pins: 2
• Colour: blue
• Lisainfo: Temperature sensor for cooling system, 2 pins
• Additional information: Temperature sensor for cooling system, 2 pins

• Thread Size: M 14x1,5
• Colour: black
• Number of pins: 1
• Switch Pressure [bar]: 0.35
• Spanner Size: 24
• Supplementary Article/Supplementary Info: with seal
• for OE number: 1535416
• Manufacturer: DELLO AUTOMEGA

• Engine Code: AR 30736
• Pressure [bar]: 0
• Thread Size: M14x1,5
• Spanner Size: 21
• Name: OLISURVELšLITUS
• Manufacturer: EPS

• Pressure [bar]: 0.3
• Thread Size: M 14 x 1,5
• Manufacturer: MEAT&DORIA

• Supplementary Article/Info 2: with plug
• Thread Size: M 14x1,5
• Housing Colour: black
• Manufacturer: FAE
• Additional information: 12430 FAE
• Lisainfo: 12430 FAE

• Pressure from [bar]: 0.2
• Pressure to [bar]: 0.5
• Thread Size: M14x1,50
• Spanner Size: 21
• Name: OLISURVELšLITUS
• Manufacturer: MAG

• Model Year from: 1990
• Number of pins: 2
• Housing Colour: green
• Colour Coding: yellow
• Supplementary Article/Info 2: with seal ring
• Weight [kg]: 0.02
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Thread Size: M12x1.5
• Spanner Size: 19
• Manufacturer: FAST

• Number of pins: 1
• Switch Pressure [bar]: 0.35
• Thread Size: M 14x1,5
• Colour: black
• Supplementary Article/Supplementary Info: with gaskets/seals
• for article number: 2324051
• Version: AM
• Manufacturer: METZGER

• Sensor Type: NTC Sensor
• Mounting Type: Bolted
• Connector Shape: rectangular
• Number of pins: 2
• Spanner Size: 19
• Thread Size: M12x1.5
• for OE number: 195321101000
• Supplementary Article/Info 2: with seal ring
• Name: Andur,Jahutusvedeliku temp.
• Manufacturer: NRF

• Engine Code: AR 30736
• Thread Size: M14x1,5
• Spanner Size: 19
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: EPS

• Thread Size: M14x1.5
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: VER

• Engine Code: AR 30737, AR 30736
• Thread Size: M14 x 1,5
• Spanner Size: 21
• Number of pins: 1
• Pressure [bar]: 0.3
• Manufacturer: AIC

General Information: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.

• Number of pins: 1
• Switch pressure from [bar]: 0.2
• Switch pressure to [bar]: 0.5
• Thread Size: M 14x1,5
• Housing Type: without housing
• Colour: black
• Supplementary Article/Supplementary Info: with gaskets/seals
• Quality: IAM
• Manufacturer: METZGER

• Thread Size: M12 x 1,5
• Spanner Size: 19
• Number of pins: 2
• Connector Shape: rectangular
• Manufacturer: ERA

• Engine Code: AR 30736
• Thread Size: M12x1,5
• Spanner Size: 19
• for article number: 1.880.113, 1.880.114, 1.880.149, 1.880.151
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: EPS

• Number of pins: 3
• Colour: black
• Material: Plastic
• Manufacturer: AIC

General Information: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.

• Housing Colour: blue
• Number of pins: 2
• Thread Size: M12X1.5-6g
• Spanner Size: 19
• Manufacturer: DELPHI
• Name: DE TS10250

• Thread Size: M12x1.5
• Manufacturer: VERNET

• Number of pins: 2
• Connector Shape: rectangular
• Socket colour: black
• External Thread [mm]: M 12x1,5
• Manufacturer: ERA

• Engine Code: AR 30737
• Mounting Type: Bolted
• Voltage [V]: 12
• Resistor [Ohm]: 2,080, 302
• Supplementary Article/Supplementary Info: with seal
• Temperature range from [°C]: 25
• Temperature range to [°C]: 80
• Thread Size: M12x1,5
• Colour: blue
• Spanner Size: 19
• Sensor Type: NTC Sensor
• Number of pins: 2
• Corresponds to the original part in colour: blue
• Manufacturer Restriction: Bosch
• Assy./disassy. by qualified personnel required!:
• Manufacturer: HELLA

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Engine Code: AR 30736, AR 30737
• Block Separation:
• Sensor Type: NTC Sensor
• Thread Size: M12 x 1,5
• Spanner Size: 19
• Colour: blue
• Number of pins: 2
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: MEY

• Alternatively:
• Supplementary Article/Supplementary Info: with seal
• Number of pins: 3
• Supplementary Article/Info 2: without cable
• Connector Shape: rectangular
• Weight [kg]: 0.024
• Alternative Repair Kit: 550144
• Manufacturer: ERA

• Construction Year from: 07.1990
• Manufacturer: BOSCH
• Name: BS 0280130026

• Chemical Properties: Oil resistant
• Number of pins: 1
• Cable Length [mm]: 80
• Cable Cross Section [mm²]: 1
• Contact surface: Tin-plated
• Supplementary Article/Info 2: with copper casing, with protection hose
• Supplementary Article/Supplementary Info: with cable tie
• Temperature range from [°C]: -25
• Temperature range to [°C]: +125
• SVHC: No SVHC present!
• Name: šhenduskaabel, olisurvelliti
• Manufacturer: HBE

Manufacturer Restriction: Opel, Fiat, Peugeot, Alfa Romeo, Lancia, Suzuki, Ford, Citroen

• Number of circuits: 3
• Lambda Sensor: Regulating Probe
• Manufacturer: KAMOKA

• Technical Information Number: Universal
• Overall Length [mm]: 315
• Number of pins: 3
• Lambda Sensor: Regulating Probe
• Manufacturer: JAPKO

• Lambda Sensor: Lambda Sensor
• Voltage [V]: 12
• Number of circuits: 3
• Weight [kg]: 0.08
• Operating Mode: Electric
• Warranty: 3 years warranty
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY
• Name: CE 09SKV903

• Engine Code: AR 30737
• Construction Year from: 07.1990
• Lambda Sensor: Regulating Probe, Heated
• Fitting Position: Exhaust Manifold
• Number of pins: 3
• Cable Length [mm]: 230
• for article number: 81014E
• Quality: OE EQUIVALENT
• Manufacturer: MEAT&DORIA

• Construction Year from: 07.1990
• Lambda Sensor: Regulating Probe
• Voltage [V]: 12
• Length [mm]: 1,670
• Number of circuits: 3
• Weight [kg]: 0.23
• Resistor [Ohm]: 4.5
• Operating Mode: Electric
• Warranty: 3 years warranty
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY
• Name: CE 09SKV546

• Lambda Sensor: Regulating Probe
• Construction Year from: 07.1990
• Engine Code: AR 30736, AR 30737
• Voltage [V]: 12
• Length [mm]: 1,665
• Number of circuits: 3
• Weight [kg]: 0.15
• Operating Mode: Electric
• Warranty: 3 years warranty
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY
• Name: CE 09SKV033

• Construction Year from: 07.1990
• Lambda Sensor: Regulating Probe, Thread pre-greased
• Line insulation design: with silicone-coated woven-fibre insulation
• Length [mm]: 1,700
• Thread Size: M18x1,5
• Cable Length [mm]: 1,530
• Conductor Number: 3
• Weight [kg]: 0.211
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Engine Code: AR 30737
• Construction Year from: 07.1990
• Lambda Sensor: Regulating Probe
• Fitting Position: before catalytic converter
• Number of circuits: 3
• Recommended change interval [km]: 160,000
• Connector/Clamp: Connector may need adjustment
• Name: LAMBDA ANDUR
• Manufacturer: BOS

• Lambda Sensor: Lambda Sensor
• Weight [kg]: 0.23
• Warranty: 3 years warranty
• Always compare old and new part (in particular OE No.):
• Manufacturer: ESEN SKV

• Lambda Sensor: Regulating Probe
• Number of pins: 3
• Cable Length [mm]: 1,550
• for OE number: 60537650
• Manufacturer: MEAT&DORIA

• Weight [kg]: 0.087
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.