• Axle alignment required after fitting:
• Control/Trailing Arm Type: Control Arm
• Fitting Position: Rear Axle Right
• Article number of the recommended special tool: V99-1020
• paired article number: V48-0212
• Weight [kg]: 1.697
• Manufacturer: VAICO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Fitting Position: Rear Axle Right, outer, Lower
• Material: Sheet Steel
• paired article number: TC3729
• Control/Trailing Arm Type: Control Arm
• Supplementary Article/Info 2: without ball joint
• Length [mm]: 380
• Width [mm]: 80
• Height [mm]: 90
• Manufacturer: DELPHI
• Name: DE TC3730

• Axle alignment required after fitting:
• Control/Trailing Arm Type: Control Arm
• Fitting Position: Rear Axle Right
• Article number of the recommended special tool: V99-1020
• paired article number: V48-0213
• Weight [kg]: 1.699
• Manufacturer: VAICO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Material: Aluminium
• Control/Trailing Arm Type: Control Arm
• Fitting Position: Rear Axle Left, Rear Axle Right, Upper
• Weight [kg]: 0.561
• Supplementary Article/Supplementary Info: with rubber mounts
• Name: Ootshoob, k„„ndmik
• Manufacturer: FEB

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Fitting Position: Rear Axle, outer, Rear, Left, Upper, Right
• Thread Size 2: Bush 14.2
• Material: Steel
• Control/Trailing Arm Type: Trailing Arm
• Supplementary Article/Info 2: without ball joint
• Length [mm]: 445
• Width [mm]: 123
• Height [mm]: 62.5
• Name: DE TC3036
• Manufacturer: DELPHI

• Fitting Position: Rear, Front Axle Right, Lower Front Axle
• Control/Trailing Arm Type: Control Arm
• Length [mm]: 364
• Inner Diameter 1 [mm]: 14.3
• paired article number: TRC4235
• Manufacturer: BGA

• Fitting Position: Upper, Rear Axle Right, Rear Axle Left
• Control/Trailing Arm Type: Control Arm
• Material: Aluminium
• Bore Ø [mm]: 14.2
• Length [mm]: 385
• replacement in pairs recommended:
• Required quantity: 2
• Name: Ootshoob, k„„ndmik
• Manufacturer: MEY

• Control/Trailing Arm Type: Control Arm
• Fitting Position: Front Axle, Left, Lower, Front
• paired article number: 72-6020
• Name: Ootshoob, k„„ndmik
• Manufacturer: MAX

• Control/Trailing Arm Type: Control Arm
• Fitting Position: Front Axle, Right, Lower, Front
• paired article number: 72-6019
• Name: Ootshoob, k„„ndmik
• Manufacturer: MAX

• Fitting Position: Front Axle Left, Upper
• Control/Trailing Arm Type: Control Arm
• Length [mm]: 304
• Material: Sheet Steel
• paired article number: 20-26684
• Weight [kg]: 1.92
• Name: DY 20-26685
• Manufacturer: DYS

• Fitting Position: Front Axle Right, Upper
• Control/Trailing Arm Type: Control Arm
• Length [mm]: 304
• Material: Sheet Steel
• paired article number: 20-26685
• Weight [kg]: 1.92
• Name: DY 20-26684
• Manufacturer: DYS

• Control/Trailing Arm Type: Control Arm
• Fabrication Number: ZWD-LR-016
• paired article number: ZWD-LR-015
• Manufacturer: NTY

Fitting Position: Front Axle Left, Lower, Front Axle, outer, Left, Front

• Control/Trailing Arm Type: Control Arm
• Fabrication Number: ZWD-LR-015
• paired article number: ZWD-LR-016
• Manufacturer: NTY

Fitting Position: Front Axle Right, Lower, Front Axle, outer, Right, Front

• Fitting Position: Front Axle Left, Lower Front Axle
• Required quantity: 1
• Control/Trailing Arm Type: Control Arm
• Length [mm]: 489.5
• Inner Diameter 1 [mm]: 14.2
• paired article number: TRC4213
• Manufacturer: BGA

• Fitting Position: Front Axle Left, outer, Rear, Left, Lower
• Vehicle Identification Number (VIN) to: HA999999
• Thread Size 1: M16x1.5
• Thread Size 2: Bush 14.2
• Material: Steel
• paired article number: TC3150
• Control/Trailing Arm Type: Trailing Arm
• Supplementary Article/Info 2: with ball joint
• Length [mm]: 422
• Width [mm]: 75
• Height [mm]: 104
• Manufacturer: DELPHI

• Fitting Position: Front Axle Right, outer, Upper, Right
• Vehicle Identification Number (VIN) to: HA999999
• Thread Size 1: Pinch Bolt 19.3mm
• Material: Aluminium
• paired article number: TC3048
• Control/Trailing Arm Type: Trailing Arm
• Camber correction [min.]: +5
• Supplementary Article/Info 2: with ball joint
• Length [mm]: 315
• Width [mm]: 305
• Height [mm]: 86
• Name: DE TC3049
• Manufacturer: DELPHI

• Fitting Position: Front Axle Left, outer, Left, Upper
• Vehicle Identification Number (VIN) to: HA999999
• Thread Size 1: Pinch Bolt 19.3mm
• Material: Aluminium
• paired article number: TC3049
• Control/Trailing Arm Type: Trailing Arm
• Camber correction [min.]: +5
• Supplementary Article/Info 2: with ball joint
• Length [mm]: 315
• Width [mm]: 305
• Height [mm]: 86
• Name: DE TC3048
• Manufacturer: DELPHI

• Fitting Position: Front Axle Left, outer, Left, Upper
• Vehicle Identification Number (VIN) to: HA999999
• Thread Size 1: Pinch Bolt 19.3mm
• Material: Aluminium
• paired article number: TC3047
• Control/Trailing Arm Type: Trailing Arm
• Camber correction [min.]: -5
• Supplementary Article/Info 2: with ball joint
• Length [mm]: 315
• Width [mm]: 305
• Height [mm]: 86
• Manufacturer: DELPHI
• Name: DE TC3046

• Fitting Position: Front Axle Right, outer, Upper, Right
• Vehicle Identification Number (VIN) to: HA999999
• Thread Size 1: Pinch Bolt 19.3mm
• Material: Aluminium
• paired article number: TC3046
• Control/Trailing Arm Type: Trailing Arm
• Camber correction [min.]: -5
• Supplementary Article/Info 2: with ball joint
• Length [mm]: 315
• Width [mm]: 305
• Height [mm]: 86
• Name: DE TC3047
• Manufacturer: DELPHI

• Control/Trailing Arm Type: Control Arm
• Fitting Position: Front Axle Right, Lower
• Manufacturer: ASHIKA

• Control/Trailing Arm Type: Trailing Arm
• Quantity Unit: Set
• Fitting Position: Lower, Front, Front Axle Right
• Cone Size [mm]: 21.5
• Material: Steel
• Rod/Strut: Push Rod
• Quality class: PJ
• Name: Control arm right

• Control/Trailing Arm Type: Trailing Arm
• Quantity Unit: Set
• Fitting Position: Lower, Front, Front Axle Left
• Cone Size [mm]: 21.5
• Material: Steel
• Rod/Strut: Push Rod
• Quality class: PJ
• Name: Control arm left

• Trim Level: with HYDRO SB
• Fitting Position: Lower, Front, Front Axle Left
• Cone Size [mm]: 21.5
• Material: Steel
• Control/Trailing Arm Type: Trailing Arm
• Observe service information:
• paired article number: D120625
• Rod/Strut: Push Rod
• Manufacturer: DENCKERMANN FILTRY

• Control/Trailing Arm Type: Control Arm
• Fitting Position: Front Axle Right, Lower
• Name: Ootshoob, k„„ndmik
• Manufacturer: JPA

• Fitting Position: Front Axle Right, outer, Upper, Right
• Vehicle Identification Number (VIN) to: HA999999
• Thread Size 1: Pinch Bolt 19.3mm
• Material: Aluminium
• paired article number: TC3037
• Control/Trailing Arm Type: Trailing Arm
• Supplementary Article/Info 2: with ball joint
• Length [mm]: 315
• Width [mm]: 305
• Height [mm]: 86
• Manufacturer: DELPHI

• Fitting Position: outer, Front Axle Left, Lower, Rear
• Vehicle Identification Number (VIN) to: HA999999
• paired article number: 8500 17563
• Control/Trailing Arm Type: Control Arm
• Supplementary Article/Info 2: with ball joint, with rubber mount
• Cone Size [mm]: 22.5
• Required quantity: 1
• Length [mm]: 363.5
• Name: Ootshoob, k„„ndmik
• Manufacturer: TRI

• Fitting Position: outer, Front Axle Right, Lower, Rear
• Vehicle Identification Number (VIN) to: HA999999
• paired article number: 8500 17564
• Control/Trailing Arm Type: Control Arm
• Supplementary Article/Info 2: with ball joint, with rubber mount
• Cone Size [mm]: 22.5
• Required quantity: 1
• Length [mm]: 363.5
• Name: Ootshoob, k„„ndmik
• Manufacturer: TRI

• paired article number: 177842
• Cone Size [mm]: 19.2
• Material: Aluminium
• Control/Trailing Arm Type: Control Arm
• Fitting Position: Upper, Front Axle Right
• Weight [kg]: 1.924
• Supplementary Article/Info 2: with bearing
• Name: Ootshoob, k„„ndmik
• Manufacturer: FEB

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• paired article number: 177841
• Cone Size [mm]: 19.3
• Material: Aluminium
• Control/Trailing Arm Type: Control Arm
• Fitting Position: Front Axle Left, Upper
• Weight [kg]: 1.925
• Supplementary Article/Info 2: with bearing
• Name: Ootshoob, k„„ndmik
• Manufacturer: FEB

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Fitting Position: Front Axle Left, outer, Left, Upper
• Vehicle Identification Number (VIN) to: HA999999
• Block Separation:
• Vehicle Identification Number (VIN) from: JA000001
• Thread Size 1: Pinch Bolt 19.3mm
• Material: Aluminium
• paired article number: TC3038
• Control/Trailing Arm Type: Trailing Arm
• Supplementary Article/Info 2: with ball joint
• Length [mm]: 315
• Width [mm]: 305
• Height [mm]: 86
• Manufacturer: DELPHI

• Control/Trailing Arm Type: Control Arm
• Fitting Position: Rear Axle Left, Rear Axle Right, Upper
• Material: Aluminium
• Manufacturer: LEMFORDER

SVHC: No information available, please contact the manufacturer!

• Fitting Position: outer, Front Axle Left, Lower, Front
• paired article number: 8500 17545
• Control/Trailing Arm Type: Control Arm
• Supplementary Article/Info 2: with ball joint, with rubber mount
• Cone Size [mm]: 21.5, 17.75
• Required quantity: 1
• Name: Ootshoob, k„„ndmik
• Manufacturer: TRI

• Fitting Position: outer, Front Axle Right, Lower, Front
• paired article number: 8500 17546
• Control/Trailing Arm Type: Control Arm
• Supplementary Article/Info 2: with ball joint, with rubber mount
• Cone Size [mm]: 21.5, 27.75
• Required quantity: 1
• Name: Ootshoob, k„„ndmik
• Manufacturer: TRI

• Fitting Position: Lower Front Axle, Left, Rear
• Control/Trailing Arm Type: Control Arm
• Supplementary Article/Info 2: with rubber mount
• Warranty: 3 years warranty or until 75,000km
• paired article number: 58154502
• Manufacturer: METZGER

• Fitting Position: Lower Front Axle, Right, Rear
• Control/Trailing Arm Type: Control Arm
• Supplementary Article/Info 2: with rubber mount
• Warranty: 3 years warranty or until 75,000km
• paired article number: 58154401
• Manufacturer: METZGER

• Fitting Position: Lower, Front, Front Axle, Left
• Control/Trailing Arm Type: Control Arm
• Length [mm]: 490
• Required quantity: 1
• Cone Size [mm]: 21.5
• Material: Cast Steel
• Supplementary Article/Info 2: with ball joint, with rubber mount
• Mounting points diameter [mm]: 14.2
• paired article number: G5-973
• External Thread [mm]: M16 x 1,50 RHT M
• Manufacturer: OPTIMAL ZAWIESZENIE

• Fitting Position: Right, Lower, Front, Front Axle
• Control/Trailing Arm Type: Control Arm
• Length [mm]: 490
• Required quantity: 1
• Cone Size [mm]: 21.5
• Material: Cast Steel
• Supplementary Article/Info 2: with ball joint, with rubber mount
• Mounting points diameter [mm]: 14.2
• paired article number: G5-972
• External Thread [mm]: M16 x 1,50 RHT M
• Manufacturer: OPTIMAL ZAWIESZENIE

• Fitting Position: Upper, Front Axle Left
• Control/Trailing Arm Type: Control Arm
• Material: Aluminium
• adjustable: can be adjusted three times
• Replace in pairs only:
• reinforced version:
• with environmental seal: Carbon neutral
• Required quantity: 1
• paired article number: 53-16 050 0028/HD
• Name: Ootshoob, k„„ndmik
• Manufacturer: MEY

General Information: Better than OE: MEYLE-HD bushings with optimized inner sleeve profile withstand greater forces and provide a longer life and performance.

• Fitting Position: Upper, Front Axle Right
• Control/Trailing Arm Type: Control Arm
• Material: Aluminium
• adjustable: can be adjusted three times
• Replace in pairs only:
• reinforced version:
• with environmental seal: Carbon neutral
• Required quantity: 1
• paired article number: 53-16 050 0027/HD
• Name: Ootshoob, k„„ndmik
• Manufacturer: MEY

General Information: Better than OE: MEYLE-HD bushings with optimized inner sleeve profile withstand greater forces and provide a longer life and performance.

• Vehicle Identification Number (VIN) from: JA000001
• Control/Trailing Arm Type: Control Arm
• Fitting Position: Front Axle, Right, Lower, Rear
• Material: Cast Steel
• paired article number: 42163 01
• Manufacturer: LEMFORDER

SVHC: No information available, please contact the manufacturer!

• Fitting Position: Front Axle Left, Left, Lower, Front
• Thread Size 1: M16x1.5
• Thread Size 2: Bush Ø14.2
• Material: Steel
• paired article number: TC3039
• Control/Trailing Arm Type: Trailing Arm
• Supplementary Article/Info 2: with ball joint
• Length [mm]: 580
• Width [mm]: 150
• Height [mm]: 105
• Manufacturer: DELPHI
• Name: DE TC3040

• Fitting Position: Front Axle Right, Right, Lower, Front
• Thread Size 1: M16x1.5
• Thread Size 2: Bush Ø14.2
• Material: Steel
• paired article number: TC3040
• Control/Trailing Arm Type: Trailing Arm
• Supplementary Article/Info 2: with ball joint
• Length [mm]: 580
• Width [mm]: 150
• Height [mm]: 105
• Manufacturer: DELPHI

• Vehicle Identification Number (VIN) to: HA999999
• Control/Trailing Arm Type: Control Arm
• Fitting Position: Front Axle, Right, Lower, Rear
• Material: Aluminium
• paired article number: 39851 01
• Name: Ootshoob, k„„ndmik
• Manufacturer: LMI

SVHC: No information available, please contact the manufacturer!

• Vehicle Identification Number (VIN) to: HA999999
• Control/Trailing Arm Type: Control Arm
• Fitting Position: Front Axle, Left, Lower, Rear
• Material: Aluminium
• paired article number: 39852 01
• Name: Ootshoob, k„„ndmik
• Manufacturer: LMI

SVHC: No information available, please contact the manufacturer!

• Control/Trailing Arm Type: Control Arm
• Fitting Position: Front Axle, Left, Lower, Front
• paired article number: 39848 01
• Name: Ootshoob, k„„ndmik
• Manufacturer: LMI

SVHC: No information available, please contact the manufacturer!

• Control/Trailing Arm Type: Control Arm
• Fitting Position: Front Axle, Right, Lower, Front
• paired article number: 39847 01
• Name: Ootshoob, k„„ndmik
• Manufacturer: LMI

SVHC: No information available, please contact the manufacturer!