Assembly categories
Filters Brake System Axle Steering Cooling / AC Electrics Towbar/Accessories Transmission Exhaust System Body Ignition Engine Windscreen Cleaning Lights Fuel Supply Interior ServiceProduct
Description
In stock
Price
(incl. VAT)
- Relay function: Air Suspension
-
Relay Number: K126,
K6342 - Supplementary Article/Info 2: with resistor
- Supplementary Article/Supplementary Info: without holder
- Voltage [V]: 12
- Temperature range to [°C]: +125
- Colour: black
-
Inductive Load [A]: 10,
20 -
Capacitive Load [A]: 10,
20 - Quantity: 350
-
Ohmic Load [A]: 10,
20 - Number of pins: 5
- Wiring Diagramme: W2
- Combi Switch Function: Changeover Contact
- Plug Type ID: C1
-
Temperature range [°C]: -
40 - Assy./disassy. by qualified personnel required!:
- Manufacturer: HELLA ELEKTRYKA
Brief Information: *** HELLA Electronics OE competence for over 60 years.
- Construction Year from: 04.2010
- Construction Year to: 06.2013
- for OE number: 61 31 6 919 113
- Current Strength [A]: 30
- Voltage [V]: 12
- Number of pins: 5
- Relay function: Normally open contact
- Protection Type (IP Code): IP5K4
-
Temperature range from [°C]: -
40 - Temperature range to [°C]: 100
- Resistor [Ohm]: 16
-
Name: JUHTSEADE,
HOOGEAEG - Manufacturer: BOS
- Pinge [V]: 12
- OE-numbri jaoks: 61 36 8 373 700
- Relee funktsioon: Suruõhukompressor
-
Seerianumber: BPP-
BM- 000 - Manufacturer: NTY
-
Name: NTY BPP-
BM- 000
Tavatellimus saadetakse E, K ja R kell 14:00. Kaup saabub kuni 3'e tööpäevaga. Tavatellimusse lähevad ainult positiivse laojäägiga tooted. Lisaks tavatellimusele on võimalik tellida ka Express kulleriga (24h). Kulleri hinda täpsusta 6 599 702, malva@lakiauto.ee.
- Relay function: Normally open contact
- Housing Colour: black
- Number of pins: 4
-
Fabrication Number: BPP-
BM- 001 - Manufacturer: NTY
-
Name: NTY BPP-
BM- 001
Tavatellimus saadetakse E, K ja R kell 14:00. Kaup saabub kuni 3'e tööpäevaga. Tavatellimusse lähevad ainult positiivse laojäägiga tooted. Lisaks tavatellimusele on võimalik tellida ka Express kulleriga (24h). Kulleri hinda täpsusta 6 599 702, malva@lakiauto.ee.
- for OE number: 61 36 8 373 700
- Relay function: Air compressor
- Voltage [V]: 12
- Manufacturer: TRUCKTEC
- Relay function: Normally open contact
- Number of pins: 5
- Number of connectors: 5
- Rated Voltage [V]: 12
- Housing Colour: black
- Manufacturer: VEMO GERMANY
-
Additional information: V20-
71- 0016 VEMO -
Lisainfo: V20-
71- 0016 VEMO
General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.
-
Relay function: Clamp 87,
Terminal 30 - Colour: light green
- Number of pins: 5
- Number of connectors: 5
- Rated Voltage [V]: 12
- Housing Colour: green
- Manufacturer: VEMO GERMANY
General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.
Laki Auto universal products
TecDoc catalogue for cars
TecDoc catalogue for trucks