• Fabrication Number: ECT-BM-011
• Manufacturer: NTY

• Thread Size: M 12x1,5
• Number of pins: 1
• Housing Colour: brown
• Manufacturer: FAE ELEKTRYKA

• Tightening torque from [Nm]: 50
• Voltage [V]: 12
• Combi Switch Function: Normally Closed Contact
• Current Strength [A]: 0.25
• Tolerance [%]: 10
• Thread Size: M12x1,5
• Spanner Size: 24
• Pressure from [bar]: 0.2
• Pressure to [bar]: 0.5
• Number of pins: 1
• Corresponds to the original part in colour: brown
• Assy./disassy. by qualified personnel required!:
• Name: Olisurvellitus
• Manufacturer: HEL

• Pressure from [bar]: 0.2
• Pressure to [bar]: 0.5
• Combi Switch Function: Normally Closed Contact
• Colour: brown
• Spanner Size: 24
• Thread Size: M12 x 1,5
• Number of pins: 1
• Name: OLISURVELšLITUS
• Manufacturer: MEY

• Switch Pressure [bar]: 0.3
• Thread Size: M12x1.5
• Sensor Type: Closed-type Sensor
• Manufacturer: VERNET

• Pressure [bar]: 5
• Housing Colour: brown
• Thread Size: M12x1.5
• Diameter [mm]: 24
• Spanner Size: 24
• Number of pins: 1
• Manufacturer: DELPHI
• Name: oil pressure sensor
• Quality class: PJ

Additional information: "Tootja: DELPHI
(kvaliteediklass: PJ)" Lisainfo: "Tootja: DELPHI
(kvaliteediklass: PJ)"

• Anduritüüp: NTC-andur
• Montaaživiis: kruvitud
• Pistikukatte kuju: ristkülik
• Pistikkontaktide arv: 2
• Pistiku värv: must
• Võtmekaugus: 22
• Keermemõõt: M12x1.5
• OE-numbri jaoks: 13621433076
• Piirangutega toode/piirangu info 2: koos rõngastihendiga
• Name: Andur,Jahutusvedeliku temp.
• Manufacturer: NRF

• Thread Size: M12x1,5
• Colour: brown
• Manufacturer: VEMO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Thread Size: M12x1.5
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: VER

• Pressure [bar]: 0.35
• Thread Size: M12 x 1,5
• Number of pins: 1
• Technical Information Number: circuit N.C.
• Manufacturer: ERA

• Colour: black
• Fabrication Number: ECT-BM-001
• Manufacturer: NTY

• Pistikukatte kuju: ristkülik
• Materjal: Plastik
• Pistikkontaktide arv: 2
• Pistikute teostus: Female
• Anduritüüp: NTC-andur
• Võtmekaugus: S22
• Keermemõõt: M12*1,5
• Name: NI 207088
• Manufacturer: NISSENS

Tehniline informatsioon: FIRST FIT - a time-saving installation! Find all additional parts such as O-rings, clip, washer in the box.

• Housing Colour: black
• Number of pins: 2
• Thread Size: M12X1.5-6g
• Spanner Size: 22
• Manufacturer: DELPHI
• Name: DE TS10270

• Fabrication Number: ECP-BM-011
• Manufacturer: NTY

• Guarantee: 3 years guarantee
• Weight [kg]: 0.01
• Number of pins: 2
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY
• Name: CE 17SKV679

• Number of pins: 2
• Name: Andur,sisendohu temperatuur
• Manufacturer: MAX

• Anduritüüp: NTC-andur
• Montaaživiis: kruvitud
• Pistikukatte kuju: ovaalne
• Pistikkontaktide arv: 2
• Pistiku värv: must
• Keermemõõt: M12x1.5
• OE-numbri jaoks: 13627797957
• Piirangutega toode/piirangu info 2: koos rõngastihendiga
• Name: Andur,Jahutusvedeliku temp.
• Manufacturer: NRF

• Thread Size: M12x1,5
• Spanner Size: 24
• Pressure from [bar]: 0.2
• Pressure to [bar]: 0.5
• Number of pins: 1
• Supplementary Article/Info 2: with seal ring
• Housing Colour: brown
• Assy./disassy. by qualified personnel required!:
• Name: HE 6ZL009600271
• Manufacturer: HELLA

• for OE number: 13 62 7 787 192
• Cable Length [mm]: 230
• Number of pins: 3
• Connector Shape: D Shape
• Fabrication Number: ECP-BM-007
• Manufacturer: NTY

• Number of pins: 2
• Housing Colour: black
• Name: Andur,sisendohu temperatuur
• Manufacturer: DLP

• Thread Size: M12 x 1,5
• Spanner Size: 22
• Number of pins: 2
• Manufacturer: ERA

• Thread Size: M12x1,5
• Spanner Size: 22
• Sensor Type: NTC Sensor
• Number of pins: 2
• Mounting Type: Vertical Screw Fitting
• Assy./disassy. by qualified personnel required!:
• Name: HE 6PT009107851
• Manufacturer: HELLA

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Number of pins: 2
• Supplementary Article/Supplementary Info: with gasket/seal
• Weight [kg]: 0.3
• Packaging length [cm]: 12
• Packaging width [cm]: 8
• Packaging height [cm]: 6

• Number of connectors: 2
• Manufacturer: ERA

• Supplementary Article/Info 2: without cable
• Number of pins: 3
• Sensor Type: Hall Sensor
• Assy./disassy. by qualified personnel required!:
• Manufacturer: ABAKUS LORO

General Information: The following information is for general and informational purposes only and does not constitute warranty terms. Warranty terms and conditions are available from our dealers and in our general terms and conditions of sale. Abakus spare/repair parts are intended only for vehicle repairs in order to restore their original functionality. Abakus spare/repair parts are used or sold to users only for the purpose of repairing vehicles to restore their original look and functionality and are not original/genuine/OE/OEM/OES replacement parts. These items do not originate from the vehicle manufacturer and may be the subject of a design not owned by Abakus and the manufacturer of this spare part. They may only be used for repairs to restore the intended vehicle to its original appearance. Our products are delivered without instruction of installation. Installation of our product may only be carried out by trained specialist technicians in specific car repairs. Products supplied by us are exclusively intended for proper and appropriate use. The warranty may become invalid in the event of: improper installation or repair, unsuitable application or use, installation or repair made outside specialist car workshops. Warranty claims are lost if the vehicle is modified and used for motor sports, tuning or similar events (except our tuning parts which are described in TecDoc and on our price list). Warranty application should include complete documentation among others: chassis no., first registration, vehicle mileage, information about LPG installation, fault memory log, pictures, our QC (quality check) code, installation invoice, contact details of the car repair workshop performing the replacement or repair. Warranty application are available in our Client Panel system. Complaints may require supplementing data such as error memory logs. Incomplete documentation may result in rejection of the claim. Any damage caused during transport is not considered quality damage and will be considered on an individual basis. The product is intended for use within the performance limits specified by the manufacturer and should only be used by qualified personnel who have been trained to operate this product. Before each use, the product should be checked for damage or fixing of its parts and not used if any defects or loose parts are found. Failure to follow the manufacturer's guidelines could result in potential product damage or even injury. Wear appropriate protective clothing if necessary when working with the product.

• Number of pins: 2
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Engine Code: M57 D30 (306D3)
• Operating voltage [V]: 12
• Sensor Type: NTC Sensor
• Number of pins: 2
• Name: Andur,sisendohu temperatuur
• Manufacturer: MEY

• for OE number: 13 62 7 787 192
• Sensor Type: Active sensor
• Manufacturer: KAMOKA

• Number of connectors: 2
• Weight [kg]: 0.007
• Name: Andur,sisendohu temperatuur
• Manufacturer: FEB
• Additional information: FE171622
• Lisainfo: FE171622

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Cable Length [mm]: 225
• Number of pins: 3
• Sensor Type: Hall Sensor
• Assy./disassy. by qualified personnel required!:
• Manufacturer: ABAKUS LORO

General Information: The following information is for general and informational purposes only and does not constitute warranty terms. Warranty terms and conditions are available from our dealers and in our general terms and conditions of sale. Abakus spare/repair parts are intended only for vehicle repairs in order to restore their original functionality. Abakus spare/repair parts are used or sold to users only for the purpose of repairing vehicles to restore their original look and functionality and are not original/genuine/OE/OEM/OES replacement parts. These items do not originate from the vehicle manufacturer and may be the subject of a design not owned by Abakus and the manufacturer of this spare part. They may only be used for repairs to restore the intended vehicle to its original appearance. Our products are delivered without instruction of installation. Installation of our product may only be carried out by trained specialist technicians in specific car repairs. Products supplied by us are exclusively intended for proper and appropriate use. The warranty may become invalid in the event of: improper installation or repair, unsuitable application or use, installation or repair made outside specialist car workshops. Warranty claims are lost if the vehicle is modified and used for motor sports, tuning or similar events (except our tuning parts which are described in TecDoc and on our price list). Warranty application should include complete documentation among others: chassis no., first registration, vehicle mileage, information about LPG installation, fault memory log, pictures, our QC (quality check) code, installation invoice, contact details of the car repair workshop performing the replacement or repair. Warranty application are available in our Client Panel system. Complaints may require supplementing data such as error memory logs. Incomplete documentation may result in rejection of the claim. Any damage caused during transport is not considered quality damage and will be considered on an individual basis. The product is intended for use within the performance limits specified by the manufacturer and should only be used by qualified personnel who have been trained to operate this product. Before each use, the product should be checked for damage or fixing of its parts and not used if any defects or loose parts are found. Failure to follow the manufacturer's guidelines could result in potential product damage or even injury. Wear appropriate protective clothing if necessary when working with the product.

• Voltage [V]: 12
• Supplementary Article/Supplementary Info: without cable pull
• Number of pins: 3
• Guarantee: 3 years guarantee
• Weight [kg]: 0.03
• Operating Mode: Electric
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY
• Name: CE 17SKV241

• Voltage [V]: 12
• Number of pins: 3
• Guarantee: 3 years guarantee
• Weight [kg]: 0.07
• Operating Mode: Electric
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY
• Name: CE 17SKV290

• Sensor Type: Hall Sensor
• Mounting Type: Screw Connection
• Shape: D Shape
• Number of pins: 3
• Fitting Depth [mm]: 23.5
• Supplementary Article/Info 2: with seal ring
• Manufacturer: NRF

• Number of pins: 2
• Colour: black
• Assy./disassy. by qualified personnel required!:
• Manufacturer: HELLA
• Name: HE 6PT009109351

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Pikkus (mm): 60
• Laius (mm): 25
• Kõrgus (mm): 45
• Kaal (kg): 0,03
• Pistikkontaktide arv: 3
• Anduritüüp: Hallsensor
• Installatsiooni pool: Sisselaskepool, Väljalaskepool
• Manufacturer: BOGAP

• Engine Code: M57 D30 (306D3)
• Sensor Type: Active sensor
• Number of pins: 3
• Name: ANDUR, VŽNTVOLL
• Manufacturer: MAX

• Resistor [Ohm]: 13
• Height [mm]: 23.8
• Manufacturer: VERNET

• Thread Size: 12 mm
• Manufacturer: VERNET

• Required quantity: 1
• Voltage [V]: 12
• Number of pins: 3
• Sensor Type: Hall Sensor
• Supplementary Article/Info 2: without cable
• Housing Colour: black
• Manufacturer: BREMI

• Voltage [V]: 12
• Number of pins: 2
• Connector Shape: oval
• Colour: black
• Supplementary Article/Supplementary Info: with gasket/seal
• Manufacturer: METZGER

Manufacturer: MAGNETI MARELLI

• Number of pins: 3
• Fitting Depth [mm]: 23.5
• Name: ANDUR,NUKKVOLLIPOSITSIOON
• Manufacturer: TRI

Manufacturer: MAGNETI MARELLI

• Number of pins: 3
• Connector Shape: oval
• Sensor Type: Hall Sensor
• Supplementary Article/Info 2: without cable
• for OE number: 13627803093
• Manufacturer: MEAT&DORIA

• Name: Andur, v„ntvoll
• Manufacturer: MAG

• Number of pins: 2
• Housing Colour: black
• Connector Shape: oval
• Manufacturer: FAE

• Manufacturer Restriction: BMW, Mercedes-Benz
• Number of pins: 2
• Cable Length [mm]: 200
• Cable Cross Section [mm²]: 0.75
• Contact surface: Silver-plated
• Supplementary Article/Supplementary Info: with socket housing, with gaskets/seals
• Supplementary Article/Info 2: with pipe
• Cable insulation material: Silicone
• Temperature range from [°C]: -25
• Temperature range to [°C]: +140
• Plug housing design: Plug sleeve housing
• SVHC: No SVHC present!
• Manufacturer: HBE

Name: Kaabli remondikomplekt, jahutusvedeliku temperatuuri andur

• Number of pins: 3
• Fitting Depth [mm]: 24
• Supplementary Article/Info 2: with seal ring
• Manufacturer: ERA

• Required quantity: 1
• Voltage [V]: 12
• Number of pins: 3
• Sensor Type: Hall Sensor
• Supplementary Article/Info 2: with cable
• Housing Colour: black
• Name: CZUJNIK POO½ENIA WAU KORB. BMW 3 E90 330D 09-
• Manufacturer: BRM

• Housing Type: with housing
• Fabrication Number: EPP-BM-002
• Manufacturer: NTY

• Number of connectors: 3
• Cable Length [mm]: 150
• Weight [kg]: 0.042
• Manufacturer: FEBI BILSTEIN

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Fitting Depth [mm]: 24
• Number of connectors: 3
• Number of mounting bores: 1
• Rated Voltage [V]: 12
• Operating temperature from [°C]: -40
• Operating temperature to [°C]: 125
• Sensor Type: Hall Sensor
• Connector Shape: D Shape
• Colour: black
• Name: SN CMP150.02
• Manufacturer: SNR

• Cable Length [mm]: 195
• Number of pins: 3
• Name: ANDUR, VŽNTVOLL
• Manufacturer: DLP

• Number of connectors: 3
• Cable Length [mm]: 150
• Weight [kg]: 0.042
• Name: SW 33 10 3640
• Manufacturer: SWAG

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Number of pins: 3
• Connector Shape: D Shape
• Supplementary Article/Info 2: without cable
• Number of mounting bores: 1
• Sensor Type: Hall Sensor
• Fitting Depth [mm]: 23
• for OE number: 13627792256
• Manufacturer: MEAT&DORIA

• Sensor Type: Hall Sensor
• Number of pins: 3
• Connector Shape: D Shape
• Supplementary Article/Info 2: without cable
• Name: Andur,Nukkvollipositsioon
• Manufacturer: VAL

• Sensor Type: Hall Sensor
• Supplementary Article/Info 2: with screw
• Cable Length [mm]: 204
• Number of pins: 3
• Name: ANDUR, VŽNTVOLL
• Manufacturer: MEY

• Engine Code: 30 6D 3
• Quality class: PJ
• Name: Air flow sensor

• Number of pins: 3
• Name: ANDUR,NUKKVOLLIPOSITSIOON
• Manufacturer: DLP

• Voltage [V]: 12
• Corresponds to the original part in colour: black
• Supplementary Article/Supplementary Info: with gasket/seal
• Number of pins: 3
• Supplementary Article/Info 2: without cable
• Sensor Type: Impulse Sensor
• Assy./disassy. by qualified personnel required!:
• Manufacturer: HELLA
• Name: HE 6PU009121631

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Cable Length [mm]: 226
• Sensor Type: Hall Sensor
• Number of pins: 3
• Assy./disassy. by qualified personnel required!:
• Manufacturer: HELLA
• Name: HE 6PU013122041

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Sensor Type: Hall Sensor
• Number of pins: 3
• Connector Shape: D Shape
• Supplementary Article/Info 2: with cable
• Manufacturer: VALEO

• Engine Code: M57 D30 (306D3)
• Voltage [V]: 12
• Number of pins: 4
• Name: OHUMASSIMOOTJA
• Manufacturer: MAX

• for OE number: 13 62 7 788 744
• Manufacturer: KAMOKA

• Voltage [V]: 12
• Housing Type: with housing
• Number of pins: 4
• New Part:
• Used part return not required:
• Weight [kg]: 0.27
• Operating Mode: Electric
• Always compare old and new part (in particular OE No.):
• Manufacturer: ENERGY

• Oxygen Sensor: Regulating Sensor
• Voltage [V]: 12
• Fitting Position: before catalytic converter
• Cable Length [mm]: 380
• Number of pins: 5
• Guarantee: 3 years guarantee
• Weight [kg]: 0.13
• Operating Mode: Electric
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY

• Voltage [V]: 12
• Housing Type: with housing
• Number of pins: 4
• Guarantee: 3 years guarantee
• New Part:
• Used part return not required:
• Weight [kg]: 0.27
• Operating Mode: Electric
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY
• Name: CE 07SKV100

• Name: OHUMASSIMOOTJA
• Manufacturer: MAG

• Housing Type: with housing
• Number of pins: 4
• Plug Type: Male
• Housing Colour: black
• Voltage [V]: 12
• Recommended additional repairs: Air Filter
• Name: OHUMASSIMOOTJA
• Manufacturer: DLP

• Construction Year from: 12.2008
• Engine Code: M57D30TU2
• Length [mm]: 24.8
• Number of pins: 3
• Supplementary Article/Info 2: with seal ring, without cable
• Shape: L Shape
• Supplementary Article/Supplementary Info: with gasket/seal
• Number of connectors: 3
• Rated Voltage [V]: 12
• Fitting Depth [mm]: 23
• Connector Shape: D Shape
• Corresponds to the original part in colour: black
• Manufacturer: VIEROL

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Required quantity: 1
• Voltage [V]: 12
• Number of pins: 4
• Name: OHUMASSIMOOTJA
• Manufacturer: BRM

• Oxygen Sensor: Regulating Sensor, Broadband Oxygen Sensor, Heated
• Fitting Position: before catalytic converter
• Cable Length [mm]: 385
• Manufacturer: DELPHI
• Name: DE ES21067-12B1

• Fitting Position: before catalytic converter
• Oxygen Sensor: Regulating Sensor, Heated
• External Thread Size: M18 x 1,5
• Spanner Size: 22
• Number of circuits: 5
• Cable Length [mm]: 406
• Weight [kg]: 0.097
• Manufacturer: FEBI BILSTEIN

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Lambda andur: Bistabiilne andur
• Pinge [V]: 12
• Värv: punane
• Garantii: 3 aastat garantii
• Ülekandeliinide arv: 5
• Kaal (kg): 0,15
• Rakendustüüp: elektriline
• Oluline on võrrelda vana uue osaga (eriti OE-numbrit):
• Manufacturer: SKV GERMANY
• Name: CE 09SKV905

• Oxygen Sensor: Broadband Oxygen Sensor
• Number of pins: 5
• Cable Length [mm]: 410
• Quality: OE EQUIVALENT
• for OE number: A0035427018
• Manufacturer: MEAT & DORIA