• Fitting Position: Rear Axle both sides, Front Axle
• Block Separation:
• Inner Diameter [mm]: 79
• Width [mm]: 13.1
• Outer Diameter [mm]: 83
• Number of Teeth: 48
• Lisainfo: 27-0296
• Additional information: 27-0296

• Fitting Position: Front Axle Left
• Sensor Type: Active sensor
• Length [mm]: 498
• Socket colour: blue

• Fitting Position: Rear Axle both sides
• Number of Teeth: 48
• Inner Diameter [mm]: 79
• Width [mm]: 13
• Manufacturer: AIC

General Information: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.

• Fitting Position: Rear Axle both sides
• Inner Diameter [mm]: 79
• Width [mm]: 13.1
• Outer Diameter [mm]: 83
• Number of Teeth, ABS ring: 48
• Manufacturer: TRISCAN
• Lisainfo: 854010403
• Additional information: 854010403

• Fitting Position: Front Axle Right
• Fabrication Number: HCA-BM-003
• paired article number: HCA-BM-002
• Manufacturer: NTY

• Fitting Position: Front Axle Left
• Fabrication Number: HCA-BM-002
• paired article number: HCA-BM-003
• Manufacturer: NTY

• Fitting Position: Front Axle both sides
• Inner Diameter [mm]: 94
• Width [mm]: 13
• Outer Diameter [mm]: 97.75
• Number of Teeth, ABS ring: 48
• Manufacturer: TRISCAN
• Lisainfo: 854011402
• Additional information: 854011402

• Fitting Position: Rear Axle Left, Rear Axle Right
• Number of Teeth, ABS ring: 48
• Inner Diameter [mm]: 79
• Width [mm]: 13
• Always compare old and new part (in particular OE No.):
• Manufacturer: METZGER

• Fitting Position: Front Axle Left
• General Information: Wheel speed sensor; front left
• Manufacturer: VIKA

Lisainfo: ABS sensor, front, left

• Construction Year to: 12.2008
• Length [mm]: 498
• Sensor Type: Active sensor
• Fitting Position: Front Axle Right
• Manufacturer: KAMOKA UK£ADY HAMULCOWE

• Fitting Position: Front Axle Left
• Construction Year from: 01.2006
• Construction Year to: 12.2008
• Length [mm]: 565
• Manufacturer: DENCKERMANN FILTRY

• Construction Year to: 12.2008
• Length [mm]: 498
• Sensor Type: Active sensor
• Fitting Position: Front Axle Left
• Manufacturer: KAMOKA

• Fitting Position: Front Axle Left
• Cable Length [mm]: 515
• Number of pins: 2
• Sensor Type: Hall Sensor
• Assy./disassy. by qualified personnel required!:
• Manufacturer: ABAKUS

General Information: The following information is for general and informational purposes only and does not constitute warranty terms. Warranty terms and conditions are available from our dealers and in our general terms and conditions of sale. Abakus spare/repair parts are intended only for vehicle repairs in order to restore their original functionality. Abakus spare/repair parts are used or sold to users only for the purpose of repairing vehicles to restore their original look and functionality and are not original/genuine/OE/OEM/OES replacement parts. These items do not originate from the vehicle manufacturer and may be the subject of a design not owned by Abakus and the manufacturer of this spare part. They may only be used for repairs to restore the intended vehicle to its original appearance. Our products are delivered without instruction of installation. Installation of our product may only be carried out by trained specialist technicians in specific car repairs. Products supplied by us are exclusively intended for proper and appropriate use. The warranty may become invalid in the event of: improper installation or repair, unsuitable application or use, installation or repair made outside specialist car workshops. Warranty claims are lost if the vehicle is modified and used for motor sports, tuning or similar events (except our tuning parts which are described in TecDoc and on our price list). Warranty application should include complete documentation among others: chassis no., first registration, vehicle mileage, information about LPG installation, fault memory log, pictures, our QC (quality check) code, installation invoice, contact details of the car repair workshop performing the replacement or repair. Warranty application are available in our Client Panel system. Complaints may require supplementing data such as error memory logs. Incomplete documentation may result in rejection of the claim. Any damage caused during transport is not considered quality damage and will be considered on an individual basis. The product is intended for use within the performance limits specified by the manufacturer and should only be used by qualified personnel who have been trained to operate this product. Before each use, the product should be checked for damage or fixing of its parts and not used if any defects or loose parts are found. Failure to follow the manufacturer's guidelines could result in potential product damage or even injury. Wear appropriate protective clothing if necessary when working with the product.

• Fitting Position: Front Axle Right
• Cable Length [mm]: 550
• Number of pins: 2
• Sensor Type: Hall Sensor
• Assy./disassy. by qualified personnel required!:
• Manufacturer: ABAKUS LORO

General Information: The following information is for general and informational purposes only and does not constitute warranty terms. Warranty terms and conditions are available from our dealers and in our general terms and conditions of sale. Abakus spare/repair parts are intended only for vehicle repairs in order to restore their original functionality. Abakus spare/repair parts are used or sold to users only for the purpose of repairing vehicles to restore their original look and functionality and are not original/genuine/OE/OEM/OES replacement parts. These items do not originate from the vehicle manufacturer and may be the subject of a design not owned by Abakus and the manufacturer of this spare part. They may only be used for repairs to restore the intended vehicle to its original appearance. Our products are delivered without instruction of installation. Installation of our product may only be carried out by trained specialist technicians in specific car repairs. Products supplied by us are exclusively intended for proper and appropriate use. The warranty may become invalid in the event of: improper installation or repair, unsuitable application or use, installation or repair made outside specialist car workshops. Warranty claims are lost if the vehicle is modified and used for motor sports, tuning or similar events (except our tuning parts which are described in TecDoc and on our price list). Warranty application should include complete documentation among others: chassis no., first registration, vehicle mileage, information about LPG installation, fault memory log, pictures, our QC (quality check) code, installation invoice, contact details of the car repair workshop performing the replacement or repair. Warranty application are available in our Client Panel system. Complaints may require supplementing data such as error memory logs. Incomplete documentation may result in rejection of the claim. Any damage caused during transport is not considered quality damage and will be considered on an individual basis. The product is intended for use within the performance limits specified by the manufacturer and should only be used by qualified personnel who have been trained to operate this product. Before each use, the product should be checked for damage or fixing of its parts and not used if any defects or loose parts are found. Failure to follow the manufacturer's guidelines could result in potential product damage or even injury. Wear appropriate protective clothing if necessary when working with the product.

• Fitting Position: Front Axle Right
• Sensor Type: Active sensor
• Length [mm]: 498
• Socket colour: blue

• Fitting Position: Front Axle
• Length [mm]: 530
• Number of pins: 2
• Connector Shape: round
• Voltage [V]: 12
• Weight [kg]: 0.1
• Colour: blue
• Operating Mode: Electric
• Always compare old and new part (in particular OE No.):
• Manufacturer: ENERGY

• for OE number: 34 52 6 752 681
• Fitting Position: Front Axle Left
• Manufacturer: TRUCKTEC

• Fitting Position: Front Axle, Front Axle Left
• paired article number: GH-701502H
• Manufacturer: AUTO-GH

• Fitting Position: Front Axle Left
• Supplementary Article/Info 2: with cable
• Length [mm]: 600
• Manufacturer: TOPRAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Fitting Position: Front Axle Right
• Length [mm]: 640
• Number of connectors: 2
• Manufacturer: JPN

• Installatsiooni pool: Esisild
• Pikkus (mm): 550
• Pistikkontaktide arv: 2
• Pistikukatte kuju: ümar
• Garantii: 3 aastat garantii
• Pinge [V]: 12
• Kaal (kg): 0,1
• Värv: sinine
• Rakendustüüp: elektriline
• Oluline on võrrelda vana uue osaga (eriti OE-numbrit):
• Name: CE 06SKV041
• Manufacturer: ESEN SKV

• Fitting Position: Front Axle Right
• Sensor Type: Active sensor
• Number of occupied pins: 2
• Cable Length [mm]: 530
• Manufacturer: DELPHI LOCKHEED HAMULCE
• Name: DE SS20042

• Installatsiooni pool: Esisild
• Pikkus (mm): 530
• Pistikkontaktide arv: 2
• Pistikukatte kuju: ümar
• Garantii: 3 aastat garantii
• Pinge [V]: 12
• Kaal (kg): 0,1
• Värv: sinine
• Rakendustüüp: elektriline
• Oluline on võrrelda vana uue osaga (eriti OE-numbrit):
• Manufacturer: SKV GERMANY
• Name: CE 06SKV040

• Fitting Position: Front Axle
• Length [mm]: 550
• Number of pins: 2
• Connector Shape: round
• Voltage [V]: 12
• Weight [kg]: 0.1
• Colour: blue
• Operating Mode: Electric
• Always compare old and new part (in particular OE No.):
• Manufacturer: ENERGY

• Construction Year from: 01.2006
• Construction Year to: 12.2008
• Installatsiooni pool: Tagasild
• Pikkus (mm): 830
• Pistikkontaktide arv: 2
• Pistikute teostus: Female
• Garantii: 3 aastat garantii
• Pinge [V]: 12
• Kaal (kg): 0,11
• Rakendustüüp: elektriline
• Pistiku värv: sinine
• Oluline on võrrelda vana uue osaga (eriti OE-numbrit):
• Manufacturer: SKV GERMANY
• Name: CE 06SKV314

• Fitting Position: Front Axle Left
• Sensor Type: Active sensor
• Number of occupied pins: 2
• Cable Length [mm]: 515
• Name: DE SS20041
• Manufacturer: DELPHI

• Construction Year to: 12.2008
• Fitting Position: Front Axle Left
• Number of pins: 2
• Connector Shape: round
• Cable Length [mm]: 498
• Overall Length [mm]: 640
• Sensor Type: Hall Sensor
• Fitting Depth [mm]: 45
• for OE number: 34526792897
• Manufacturer: MEAT&DORIA

• Construction Year to: 12.2008
• Fitting Position: Front Axle Right
• Number of pins: 2
• Connector Shape: round
• Cable Length [mm]: 498
• Overall Length [mm]: 640
• Sensor Type: Hall Sensor
• Fitting Depth [mm]: 45
• for OE number: 34526792896
• Manufacturer: MEAT&DORIA

• Fitting Position: Front Axle Right
• Overall Length [mm]: 630
• Length [mm]: 45
• Sensor Type: Active sensor
• Socket colour: blue
• Cable Length [mm]: 470
• paired article number: 30047
• Weight [kg]: 0.07
• Manufacturer: ABS

• Fitting Position: Front Axle Right
• Length [mm]: 640
• Braking/Driving Dynamics: for vehicles with ABS
• Number of pins: 2
• Rated Voltage [V]: 12
• Required quantity: 1
• Colour: blue
• Cable Length [mm]: 568
• Sensor Type: Hall Sensor, Active sensor
• Number of connectors: 2
• Supplementary Article/Info 2: with cable
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Required quantity: 1
• Fitting Position: Front Axle Left
• Supplementary Article/Info 2: with cable
• Manufacturer: BREMI

• Required quantity: 1
• Fitting Position: Front Axle Right
• Supplementary Article/Info 2: with cable
• Manufacturer: BREMI

• Fitting Position: Front Axle Left
• Overall Length [mm]: 630
• Length [mm]: 45
• Sensor Type: Active sensor
• Socket colour: blue
• Cable Length [mm]: 465
• paired article number: 30048
• Weight [kg]: 0.07
• Manufacturer: ABS

• Required quantity: 2
• Fitting Position: Rear Axle
• Supplementary Article/Info 2: with cable
• Manufacturer: BREMI

• Fitting Position: Rear Axle
• Overall Length [mm]: 920
• Length [mm]: 23
• Sensor Type: Active sensor
• Socket colour: blue
• Cable Length [mm]: 780
• paired article number: 30266
• Weight [kg]: 0.08
• Manufacturer: ABS

• paired article number: 24609
• Length [mm]: 640
• Number of connectors: 2
• Fitting Position: Front Axle Right
• Weight [kg]: 0.064
• Manufacturer: FEBI HAMULCE

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Fitting Position: Rear Axle
• Sensor Type: Active sensor
• Number of occupied pins: 2
• Cable Length [mm]: 820
• Manufacturer: DELPHI

• Fitting Position: Front Axle Left, Front Axle
• Required quantity: 1
• Voltage [V]: 12
• Number of pins: 2
• Cable Length [mm]: 468
• Sensor Type: Hall Sensor
• Assy./disassy. by qualified personnel required!:
• Manufacturer: HELLA

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Construction Year to: 07.2008
• Fitting Position: Front Axle Right
• Sensor Type: Active sensor
• Supplementary Article/Info 2: with cable
• Overall Length [mm]: 575
• Temperature range from [°C]: -40
• Temperature range to [°C]: 150
• Manufacturer: BOSCH

• Construction Year to: 07.2008
• Fitting Position: Front Axle Left
• Sensor Type: Active sensor
• Supplementary Article/Info 2: with cable
• Overall Length [mm]: 575
• Temperature range from [°C]: -40
• Temperature range to [°C]: 150
• Manufacturer: BOSCH

• Braking/Driving Dynamics: for vehicles with ABS
• Cable Length [mm]: 515
• Fitting Position: Front Axle Right
• Manufacturer: SNR

• Construction Year from: 01.2006
• Construction Year to: 12.2008
• Fitting Position: Front Axle Right
• Length [mm]: 565
• MAPP code available:
• Manufacturer: ATE

• Construction Year from: 01.2006
• Construction Year to: 12.2008
• Fitting Position: Front Axle Left
• Length [mm]: 565
• MAPP code available:
• Manufacturer: ATE