Assembly categories
Filters Brake System Axle Steering Cooling / AC Electrics Towbar/Accessories Transmission Exhaust System Body Ignition Engine Windscreen Cleaning Lights Fuel Supply Interior ServiceProduct
Description
In stock
Price
(incl. VAT)
- Engine Code: CSLC
- Quantity per packing unit: 25
- Material: Silicone
- Colour: anthracite
- Capacity [ml]: 70
- Temperature range from [°C]: 50
- Temperature range to [°C]: 320
- Packing Type: Tube
-
only in connection with: 70-
31415- 00 - Manufacturer: REINZ
-
Name: RN 70-
31414- 10 -
Additional information: RNZ70-
31414- 10 -
Lisainfo: RNZ70-
31414- 10
Chemical Properties: not solvent-bearing, Permanently elastic, hardening
- Fitting Position: engine sided
-
Multi-piece: two-
piece - Observe system fill quantity:
-
Material: ACM
(Polyacrylate) - Manufacturer: TOPRAN
General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.
- Weight [kg]: 0.008
- Manufacturer: METALCAUCHO
- Fitting Position: engine sided
-
Material: ACM
(Polyacrylate) -
Multi-piece: two-
piece - Manufacturer: METALCAUCHO
- Quantity per packing unit: 12
- Packing Type: Tube
- Capacity [ml]: 70
- Material: Silicone
- Colour: beige
- Observe mounting information:
-
Temperature range from [°C]: -
60 - Temperature range to [°C]: 315
- Available as universal article as well, see article no.: 030.793 Dirko
- Manufacturer: ELRING
Chemical Properties: Permanently elastic, not solvent-bearing, UV resistant
Supplementary Article/Info 2: with bolts/screws
- Number of Gaskets/Seals/Seal Rings: 3
- Manufacturer: FAST
- Quantity per packing unit: 4
- Manufacturer: DR MOTOR
- Engine Code: CSLC
-
Chemical Properties: not solvent-
bearing - Packing Type: Tube
- Capacity [ml]: 75
- Material: Silicone
-
Temperature range from [°C]: -
60 - Temperature range to [°C]: +320
- Supplementary Article/Info 2: not contained in set
- Manufacturer: AJUSA
- Lisainfo: AJU75000200
- Additional information: AJU75000200
- Height [mm]: 18.5
- Length [mm]: 65.2
- Width [mm]: 68.2
- Material: Plastic
- Manufacturer: VAICO
Supplementary Article/Info 2: with bolts/screws, with seal ring, with bore for oil-level sensor General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.
Manufacturer: ELRING
- Material: Rubber
-
for article number: V15-
60- 6061 - Manufacturer: VEMO GERMANY
General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.
- Weight [kg]: 0.008
- Manufacturer: FEBI BILSTEIN
General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.
Laki Auto universal products
TecDoc catalogue for cars
TecDoc catalogue for trucks