• Fitting Position: Rear Axle Left, Rear Axle Right, outer
• for vehicles with gross vehicle weight [kg]: 3,000, 3,500
• Quantity per packing unit: 2
• Rod/Strut: for coupling rod
• Mounting Type: Rubber-Metal Mount
• Outer Diameter [mm]: 26
• Inner Diameter [mm]: 12
• Width [mm]: 26
• Replace in pairs only:
• Name: Puks - K„„ndmik DB P. 207
• Manufacturer: HAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Quantity per packing unit: 10
• Fitting Position: Front Axle Left, Front Axle Right
• Inner Diameter 1 [mm]: 12
• Manufacturer: VAICO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Stabiliser Bar Diameter [mm]: 17
• for PR number: 0BC
• Fitting Position: Rear Axle Left, Rear Axle Right
• Inner Diameter [mm]: 15
• Lisainfo: Grommet for stabilizer, rear, ®15.5 mm
• Additional information: Grommet for stabilizer, rear, ®15.5 mm

• Fitting Position: Rear Axle both sides
• Length [mm]: 26
• Inner Diameter [mm]: 12
• Outer Diameter [mm]: 26
• Material: Rubber/Metal
• Manufacturer: FAST

• vajaminev tükihulk: 2
• Kaal (kg): 0,08
• Pikkus (mm): 45
• Laagritüüp: Kummipuks
• Siseläbimõõt [mm]: 19
• Installatsiooni pool: Tagasild
• Manufacturer: TED

Name: Paigutus - K„„ndmik DB T. SPRINTER 906 ALL 2,1-3,5 06-

• for PR number: 0X9, 1X9
• Fitting Position: Front Axle Left, Front Axle Right
• Inner Diameter [mm]: 21
• Manufacturer: JP GROUP
• Lisainfo: PAKENDIS 10 tk
• Additional information: PAKENDIS 10 tk

• Fitting Position: inner, Rear Axle Left, Rear Axle Right
• for OE number: 051 188 00 AA
• Manufacturer: GSP ZAWIESZENIE

• for PR number: 1X9, 0X9
• Fitting Position: Front Axle
• Inner Diameter [mm]: 21
• Mounting Type: Rubber Mount
• for OE number: 7H0411313
• Manufacturer: DELLO AUTOMEGA

• Fitting Position: Front Axle, both sides, Front
• Quality: OE Performance
• Material: Rubber
• Colour: black
• Weight [g]: 48
• Inner Diameter [mm]: 21
• Manufacturer: GATES-ZAWIESZENIE

• Fitting Position: Rear Axle Left, Rear Axle Right
• Quantity per packing unit: 2
• Mounting Type: Rubber Mount
• Stabiliser Bar Diameter [mm]: 25
• Replace in pairs only:
• Quantity per axle: 2
• Manufacturer: TOPRAN

for combined PR number: K4F+1UA, K4F+1UB, K4F+1UC, K4F+1UM, K4F+1UU, K4G+1UA, K4G+1UB, K4G+1UC, K4G+1UM, K4G+1UU General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Fitting Position: Front Axle
• for PR number: 1X9, 0X9
• Mounting Type: Rubber Mount
• Inner Diameter [mm]: 21
• SVHC: No SVHC present!
• Name: Kinnitus,stabilisaator
• Manufacturer: FAG

• Production date from: 05/11
• Production date to: 12/16
• Quantity per packing unit: 2
• Fitting Position: Front Axle, inner
• Mounting Type: Rubber Mount
• Stabiliser Bar Diameter [mm]: 22
• Inner Diameter [mm]: 20.5
• Length [mm]: 52
• Width [mm]: 50
• Height [mm]: 42
• for OE number: 7H0411313
• Manufacturer: SASIC

• Fitting Position: Rear Axle both sides
• Length [mm]: 36
• Inner Diameter [mm]: 12
• Outer Diameter [mm]: 32
• Material: Rubber/Metal
• Manufacturer: FAST

• Fitting Position: Rear Axle Upper, Rear Axle Lower
• Length [mm]: 26
• Inner Diameter [mm]: 12
• Outer Diameter [mm]: 26
• Material: Rubber/Metal
• Weight [kg]: 0.035
• Name: Puks - K„„ndmik DB P. 207-408
• Manufacturer: FEB
• Additional information: FE07200
• Lisainfo: FE07200

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Fitting Position: Rear Axle
• Inner Diameter [mm]: 27
• General Information: Rubber bush for stabilizer bar; 27mm
• Manufacturer: VIKA

• for PR number: 1X9, 0X9
• Fitting Position: Front Axle Left, Front Axle Right
• Stabiliser Bar Diameter [mm]: 21
• Observe dimensions:
• Name: Paigutus - K„„ndmik VW P. T5 03-
• Manufacturer: MAX

• Fitting Position: Rear Axle
• General Information: Bush for stabilizer coupling rod
• Manufacturer: VIKA

• Length [mm]: 45
• Fitting Position: Front Axle, inner
• Required quantity: 2
• Mounting Type: Rubber Mount
• Weight [kg]: 0.093
• Inner Diameter [mm]: 20
• Name: Kinnitus,stabilisaator
• Manufacturer: TED

• Fitting Position: Rear Axle Upper, Rear Axle Lower
• Length [mm]: 26
• Inner Diameter [mm]: 12
• Outer Diameter [mm]: 26
• Material: Rubber/Metal
• Weight [kg]: 0.035
• Name: SW 10 61 0050
• Manufacturer: SWAG

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• for PR number: 0BC
• Fitting Position: Rear Axle
• Diameter [mm]: 30
• Inner Diameter [mm]: 30
• Manufacturer: FEBEST

• Fitting Position: Front Axle
• for OE number: 7H0 411 313
• Manufacturer: GSP

• for PR number: 0BC
• Fitting Position: Rear Axle
• Mounting Type: Rubber Mount
• Inner Diameter [mm]: 16
• Width [mm]: 54
• Height [mm]: 53
• for OE number: 68013812AA, 2E0511413G
• Manufacturer: DELLO AUTOMEGA

• for OE number: 2E0511413P
• Fitting Position: Rear
• Name: DA DSS1367
• Manufacturer: DAYCO

• Fitting Position: Front Axle both sides, Rear Axle both sides
• Inner Diameter [mm]: 12.2
• Outer Diameter [mm]: 26.5
• Name: ALT 86072AL
• Manufacturer: ALTE AUTOMOTIVE

• Fitting Position: Rear Axle
• Inner Diameter [mm]: 12
• Outer Diameter [mm]: 32.3
• Width [mm]: 36
• Mounting Type: Rubber Mount
• Name: ALT 85030AL
• Manufacturer: ALTE AUTOMOTIVE

• Fitting Position: Front
• Material: Rubber
• Manufacturer: KAMOKA

• Fitting Position: Rear Axle both sides
• Inner Diameter [mm]: 16
• Manufacturer: FAST

• Fitting Position: Rear Axle
• Thickness [mm]: 55
• Length [mm]: 48
• Width [mm]: 52
• Inner Diameter [mm]: 11
• Outer Diameter [mm]: 50
• Manufacturer: MERTZ

• Fitting Position: Front Axle
• Inner Diameter [mm]: 21
• Width [mm]: 42
• Mounting Type: Rubber Mount
• Name: ALT 80876AL
• Manufacturer: ALTE AUTOMOTIVE

• for PR number: 0BC
• Fitting Position: Rear Axle
• Manufacturer: FEBEST

• Stabiliser Bar Diameter [mm]: 17
• for PR number: 0BC
• Observe service information:
• Fitting Position: Rear Axle Left, Rear Axle Right
• Width [mm]: 54
• Thickness [mm]: 53
• Inner Diameter [mm]: 16
• Name: Kinnitus,stabilisaator
• Manufacturer: MAX

• Fitting Position: Front Axle
• Diameter [mm]: 21
• Inner Diameter [mm]: 21
• Manufacturer: FEBEST

• Fitting Position: Front Axle both sides
• Weight [kg]: 0.15
• Thickness [mm]: 57
• Length [mm]: 47
• Width [mm]: 52
• Inner Diameter [mm]: 20
• General Information: Rubber bush for stabilizer bar; 20mm
• Manufacturer: VIKA

• Fitting Position: Rear Axle
• Inner Diameter [mm]: 33
• Manufacturer: FEBEST

• Quantity per packing unit: 2
• for OE number: 906 326 0481
• Inner Diameter [mm]: 33
• Mounting Type: Rubber Mount
• Fitting Position: Rear Axle
• Manufacturer: TRU

Name: Paigutus - K„„ndmik DB T. SPRINTER/CRAFTER 06- 30MM

• Fitting Position: Rear Axle both sides
• Inner Diameter [mm]: 24
• Mounting Type: Rubber Mount
• Quality class: PJ
• Name: Stabilizer mount left=right

• Fitting Position: Rear Axle Left, Rear Axle Right, inner
• Inner Diameter [mm]: 28
• Outer Diameter [mm]: 50
• Length [mm]: 46
• paired article number: 271686
• Weight [kg]: 0.07
• Installation Information: Important: Observe Fitting Instructions
• Manufacturer: ABS

• Fitting Position: Front
• Weight [g]: 96
• Inner Diameter [mm]: 23
• Outer Diameter [mm]: 50
• Length [mm]: 45
• Name: IM 32128
• Manufacturer: ORIGINAL IMPERIUM

General Information: The installation of this product can be performed only in a workshop environment by trained professionals

• Width [mm]: 52
• Thickness [mm]: 35
• Inner Diameter [mm]: 21
• Fitting Position: Front Axle
• Weight [kg]: 0.054
• Name: Paigutus - K„„ndmik VW P. T5 03-
• Manufacturer: FEB

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Stabiliser Bar Diameter [mm]: 17
• for PR number: 0BC
• old version:
• Width [mm]: 54
• Thickness [mm]: 53
• Inner Diameter [mm]: 15.5
• Fitting Position: Rear Axle
• Weight [kg]: 0.09
• Manufacturer: FEBI BILSTEIN

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Width [mm]: 52
• Thickness [mm]: 35
• Inner Diameter [mm]: 21
• Fitting Position: Front Axle
• Weight [kg]: 0.054
• Name: SW 30 92 6540
• Manufacturer: SWAG

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Fitting Position: Front
• Stabiliser Bar Diameter [mm]: 23
• for PR number: 0AC
• Name: Remondikomplekt,stabilisaatorilaager
• Manufacturer: MAX

• Vehicle type: Crafter 35
• for PR number: 0AC
• Fitting Position: Front Axle
• Diameter [mm]: 23
• Inner Diameter [mm]: 20
• Manufacturer: FEBEST

• Fitting Position: Front Axle Left, Front Axle Right
• Inner Diameter [mm]: 12
• Outer Diameter [mm]: 27
• Length [mm]: 26
• paired article number: 270700
• Weight [kg]: 0.04
• Installation Information: Important: Observe Fitting Instructions
• Manufacturer: ABS

• for PR number: 1X9, 0X9
• Fitting Position: Front Axle Left, Front Axle Right
• Inner Diameter [mm]: 21
• Stabiliser Bar Diameter [mm]: 21
• Required quantity: 2
• Name: Paigutus - K„„ndmik VW P. T5 03-
• Manufacturer: MEY

• Stabiliser Bar Diameter [mm]: 17
• for PR number: 0BC
• old version:
• Width [mm]: 54
• Thickness [mm]: 53
• Inner Diameter [mm]: 15.5
• Fitting Position: Rear Axle
• Weight [kg]: 0.09
• Name: SW 10 93 8536
• Manufacturer: SWAG

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Vehicle type: Crafter 35
• Quality: OE Performance
• Material: Rubber, Plastic
• Fitting Position: Front
• Colour: black
• Weight [g]: 82
• Inner Diameter [mm]: 23
• Manufacturer: GATES-ZAWIESZENIE

• Fitting Position: Front Axle
• Inner Diameter [mm]: 20
• Outer Diameter [mm]: 45
• Length [mm]: 52
• Required quantity: 2
• Mounting Type: Rubber Mount
• Height [mm]: 47
• Name: ALT 88159AL
• Manufacturer: ALTE AUTOMOTIVE

• for combined PR number: K4A+0BD+1P2
• Fitting Position: Front Axle Left, Front Axle Right, Front
• Mounting Type: Rubber Mount
• Inner Diameter [mm]: 24
• Guarantee: 3 years guarantee or up to 75,000km
• Manufacturer: METZGER

• Vehicle type: Crafter 35
• for PR number: 0AB
• Fitting Position: Front Axle
• Diameter [mm]: 20
• Inner Diameter [mm]: 16
• Manufacturer: FEBEST

• Fitting Position: Front Axle
• for PR number: 0AB
• Mounting Type: Rubber Mount
• Inner Diameter [mm]: 20
• SVHC: No SVHC present!
• Manufacturer: FAG
• Name: LU 819026910

• Fitting Position: Front Axle
• Diameter [mm]: 20
• Weight [g]: 150
• Name: IM 32025
• Manufacturer: ORIGINAL IMPERIUM

General Information: The installation of this product can be performed only in a workshop environment by trained professionals

• Engine Code: CSLB
• Fitting Position: Front Axle, Rear Axle
• Block Separation:
• new version:
• Length [mm]: 111
• Width [mm]: 47
• Thickness [mm]: 59
• Inner Diameter [mm]: 50
• Inner Diameter 1 [mm]: 10.7
• Weight [kg]: 0.21
• Manufacturer: FEB

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions. Name: Kinnitus - K„„ndmik STAB. DB P. SPRINTER/CRAFTER 06-

• Fitting Position: Front Axle both sides
• Inner Diameter [mm]: 20
• Length [mm]: 52.5
• Required quantity: 2
• Mounting Type: Rubber Mount
• Name: ALT 90939AL
• Manufacturer: ALTE AUTOMOTIVE

• for vehicles with gross vehicle weight [kg]: 3,000, 3,500
• Production date from: 01.07.2012
• Fitting Position: Front Axle Left, Front Axle Right, inner
• Mounting Type: Rubber Mount
• Stabiliser Bar Diameter [mm]: 21
• Replace in pairs only:
• Shape: slotted
• for OE number: 906 326 22 81, 2E0 511 413N
• Quantity per axle: 2
• Manufacturer: TOPRAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Fitting Position: Rear, outer, Left, Right, Upper
• paired article number: 1
• Inner Diameter 1 [mm]: 12
• Outer Diameter 1 [mm]: 32
• Thickness 1 [mm]: 36
• Manufacturer: DELPHI
• Name: DE TD1831W

• Diameter [mm]: 20
• Fitting Position: Front Axle Left, Front Axle Right
• Manufacturer: VAICO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• for PR number: 1X9, 0X9
• Fitting Position: Front Axle Left, Front Axle Right
• Stabiliser Bar Diameter [mm]: 21
• Quantity per axle: 2
• Observe dimensions:
• Name: Paigutus - K„„ndmik VW P. T5 03- 21MM
• Manufacturer: LMI

SVHC: No information available, please contact the manufacturer!

• Fitting Position: inner, Front Axle both sides
• Required quantity: 2
• paired article number: VKDS 358010
• Manufacturer: SKF

• Fitting Position: Front Axle
• for PR number: 0AC
• Laagritüüp: Kummipuks
• Siseläbimõõt [mm]: 24
• SVHC: SVHS aineid ei esine
• Manufacturer: FAG

• Fitting Position: Rear Axle Left, Rear Axle Right
• Material: Rubber
• Length [mm]: 48
• Width [mm]: 52
• Inner Diameter [mm]: 18
• Manufacturer: FAST

• Fitting Position: Rear Axle, Rear
• Quality: OE Performance
• Material: Rubber, Metal
• Colour: black
• Weight [g]: 150
• Inner Diameter [mm]: 10
• Manufacturer: GATES

• Fitting Position: Front Axle, Front
• Quality: OE Performance
• Material: Rubber, Metal
• Colour: black
• Weight [g]: 146
• Inner Diameter [mm]: 20
• Manufacturer: GATES

• Fitting Position: Rear
• Quantity per packing unit: 2
• Inner Diameter 1 [mm]: 16
• Thickness 1 [mm]: 45
• Manufacturer: DELPHI
• Name: DE TD4217W

• Fitting Position: Rear, both sides
• Quantity per packing unit: 2
• Name: DE TD1141W
• Manufacturer: DELPHI

• Installatsiooni pool: Tagasild mõlemapoolselt
• Siseläbimõõt [mm]: 12,2
• Laagritüüp: Kummipuks
• Pikkus (mm): 36
• Kaal (kg): 0,088
• Manufacturer: RTS

• Production date to: 03/18
• Fitting Position: Rear Axle, inner
• Mounting Type: Rubber Mount
• Stabiliser Bar Diameter [mm]: 11
• Inner Diameter [mm]: 9.5
• Length [mm]: 56
• Width [mm]: 48
• Height [mm]: 47
• for OE number: 9063262181
• Manufacturer: SASIC

• Stabiliser Bar Diameter [mm]: 21
• for PR number: 0BD, 0WC
• Block Separation:
• Length [mm]: 71
• Width [mm]: 56
• Thickness [mm]: 69
• Inner Diameter [mm]: 30
• Outer Diameter [mm]: 71
• Fitting Position: Rear Axle
• Weight [kg]: 0.22
• Manufacturer: FEB
• Additional information: FE45867
• Lisainfo: FE45867

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions. Name: Paigutus - K„„ndmik DB T. SPRINTER/CRAFTER 06- 30MM

• Fitting Position: Front, Left, Right, Lower, inner
• Inner Diameter [mm]: 20
• Manufacturer: HUTCHINSON

• Observe dimensions:
• Fitting Position: Rear Axle Right, Rear Axle Left
• Inner Diameter [mm]: 18
• Required quantity: 2
• Manufacturer: MEY

Name: Paigutus - K„„ndmik DB BM 906 SPRINTER 06/06- VW CRAFTER 04/06-07/11 (WZMOCNIONA ALUMINIUM)

• for PR number: 0BC
• Fitting Position: Rear Axle Left, Rear Axle Right
• Inner Diameter [mm]: 10
• Stabiliser Bar Diameter [mm]: 17
• Required quantity: 2
• Manufacturer: MEY

Name: Paigutus - K„„ndmik DB T. SPRINTER/CRAFTER 06- 17MM

• Stabiliser Bar Diameter [mm]: 28
• Length [mm]: 64
• Width [mm]: 72
• Thickness [mm]: 70
• Inner Diameter [mm]: 27
• Material: Rubber
• Fitting Position: Rear Axle
• Weight [kg]: 0.25
• Name: Kinnitus,stabilisaator
• Manufacturer: FEB

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Stabiliser Bar Diameter [mm]: 17
• for PR number: 0BC
• new version:
• Length [mm]: 48
• Width [mm]: 52
• Thickness [mm]: 55
• Inner Diameter [mm]: 11
• Outer Diameter [mm]: 50
• Fitting Position: Rear Axle
• Weight [kg]: 0.15
• Manufacturer: FEB

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions. Name: Paigutus - K„„ndmik DB T. SPRINTER/CRAFTER 06- 17MM