• Switch point from [bar]: 0.75
• Switch point to [bar]: 1.05
• Colour Coding: grey
• Number of connectors: 1
• External Thread [mm]: M10x1
• Manufacturer: JP GROUP
• Lisainfo: PAKENDIS 10 tk
• Additional information: PAKENDIS 10 tk

• Engine Code: AXD
• Vehicle Identification Number (VIN) from: 7J-6-000 001
• Vehicle Identification Number (VIN) to: 7J-6-050 000
• Thread Size: M10x1
• Colour: grey
• Number of pins: 1
• Manufacturer: DELLO AUTOMEGA

• Fabrication Number: ECC-AU-002
• Supplementary Article/Info 2: with seal ring
• Thread Size: M10x1
• Socket colour: grey
• Number of pins: 1

• Connector Shape: D Shape
• Operating Mode: Hydraulic
• Colour Coding: grey
• Thread Size: M 10
• Thread Pitch [mm]: 1
• Number of pins: 1
• Control Range [bar]: 0,75 - 1,05
• Supplementary Article/Info 2: with seal ring
• for OE number: 038 919 081M, 955 606 091 10, 1 469 771
• Manufacturer: TOPRAN HANS PRIES

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Colour Coding: grey
• Number of pins: 2
• Manufacturer: JP GROUP
• Lisainfo: Sender for water temperature gauge, 2 pins
• Additional information: Sender for water temperature gauge, 2 pins

• Colour Coding: grey
• Fabrication Number: ECT-VW-000
• Manufacturer: NTY
• Name: NTY ECT-VW-000

• General Information: temperature sensor
• Manufacturer: VIKA

• Vehicle Identification Number (VIN) from: 7J-8-000 001
• Vehicle Identification Number (VIN) to: 7J-8-030 000
• Number of pins: 2
• Colour: grey
• Length [mm]: 20
• Diameter [mm]: 20
• Manufacturer: DELLO AUTOMEGA

• Fabrication Number: ECT-AU-005
• Number of pins: 2
• Supplementary Article/Info 2: with seal ring
• Sensor Type: NTC Sensor
• Socket colour: black

• Colour Coding: grey
• Number of pins: 2
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: MAX

• Switch Pressure [bar]: 0.9
• Thread Size: M10x1.0
• Sensor Type: Open-style sensor
• Manufacturer: VERNET

• Connector Shape: oval, D Shape
• Colour Coding: grey
• Sensor Type: NTC Sensor
• Number of pins: 2
• Consult accessories list for recommended additional repairs:
• Manufacturer: TOPRAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Pressure [bar]: 10.5
• Housing Colour: grey
• Thread Size: M10×1-6g
• Diameter [mm]: 24
• Spanner Size: 24
• Number of pins: 1
• Name: OLISURVELšLITUS
• Manufacturer: DLP
• Quality class: PJ

Additional information: "Tootja: DELPHI
(kvaliteediklass: PJ)" Lisainfo: "Tootja: DELPHI
(kvaliteediklass: PJ)"

• Number of connectors: 2
• Manufacturer: 3RG

• External Thread Size: M10 x 1
• Spanner Size: 22
• Number of connectors: 1
• Colour: grey
• Shifting Points [bar]: 0.9
• Weight [kg]: 0.031
• Supplementary Article/Info 2: with seal ring
• Manufacturer: FEBI BILSTEIN

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• External Thread Size: M10 x 1
• Spanner Size: 22
• Number of connectors: 1
• Colour: grey
• Shifting Points [bar]: 0.9
• Weight [kg]: 0.031
• Supplementary Article/Info 2: with seal ring
• Manufacturer: SWAG
• Name: SW 30 91 9016

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• for OE number: 06A 919 501
• Manufacturer: TRUCKTEC AUTOMOTIVE

• Engine Code: AXD
• Colour: grey
• Pressure to [bar]: 1.05
• Pressure from [bar]: 0.75
• Pressure [bar]: 1
• Thread Size: M10x1
• Spanner Size: 24
• Name: OLISURVELšLITUS
• Manufacturer: EPS

• Thread Size: M20
• Number of pins: 2
• Housing Colour: grey
• Connector Shape: oval
• Manufacturer: ERA

• Thread Size: M 10x1
• Housing Colour: grey
• Pressure [bar]: 0.9
• Manufacturer: FAE

• Engine Code: AXD
• Colour Coding: grey
• for article number: 1.660.015K, 1.830.278K, 1.879.946
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: EPS
• Additional information: 1-830-278
• Lisainfo: 1-830-278

• Voltage [V]: 12
• Combi Switch Function: Normally Open Contact
• Thread Size: M10x1
• Colour: grey
• Spanner Size: 24
• Pressure from [bar]: 0.75
• Pressure to [bar]: 1.05
• Number of pins: 1
• Corresponds to the original part in colour: grey
• Assy./disassy. by qualified personnel required!:
• Manufacturer: HELLA

• Engine Code: AXD, BNZ
• Operating Mode: Mechanical
• Number of pins: 2
• Combi Switch Function: Normally Open Contact
• Colour: blue
• Material: Plastic
• Manufacturer: AIC

General Information: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.

• Model Year to: 2005
• Block Separation:
• for model year: 2006, 2007, 2008
• Model Year from: 2009
• Pressure from [bar]: 0.75
• Pressure to [bar]: 1.05
• Combi Switch Function: Normally Open Contact
• Colour: grey
• Spanner Size: 24
• Thread Size: M10 x 1,0
• Number of pins: 1
• Name: OLISURVELšLITUS
• Manufacturer: MEY

Vehicle Identification Number (VIN) from: 7H-3-000 001, 7J-3-000 001, 7H-6-000 001, 7J-6-000 001, 7H-7-000 001, 7J-7-000 001, 7H-8-000 001, 7J-8-000 001, 7H-9-000 001, 7H-9-200 000 Vehicle Identification Number (VIN) to: 7H-3-001 000, 7J-3-001 000, 7H-6-200-000, 7J-6-050 000, 7H-7-200 000, 7J-7-040 000, 7H-8-200 000, 7J-8-030 000, 7J-9-000 001, 7J-9-020 000

• Number of pins: 2
• Colour Coding: grey
• Supplementary Article/Info 2: with seal ring
• Manufacturer: AIC

General Information: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.

• Number of pins: 3
• Fabrication Number: ECP-VW-011

• Number of connectors: 2
• Colour Coding: grey
• Screw length below head [mm]: 20
• Weight [kg]: 0.015
• Supplementary Article/Supplementary Info: with seal, with retaining spring
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: FEB

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Number of connectors: 2
• Colour Coding: grey
• Screw length below head [mm]: 20
• Weight [kg]: 0.03
• Supplementary Article/Supplementary Info: with retaining spring, with seal
• Manufacturer: SWAG

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Sensor Type: NTC Sensor
• Supplementary Article/Info 2: with seal ring
• Colour: black
• Number of pins: 2
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: MEY

• Colour Coding: grey
• Corresponds to the original part in colour: black
• Number of pins: 2
• Supplementary Article/Supplementary Info: with seal
• Quality: IAM
• Article number of recommended accessories: 0899250, 0905513
• Power [W]: 0.06
• Manufacturer: METZGER

• Number of pins: 3
• Cable Length [mm]: 455
• Manufacturer: ABAKUS DEPO/LORO

General Information: The following information is for general and informational purposes only and does not constitute warranty terms. Warranty terms and conditions are available from our dealers and in our general terms and conditions of sale. Abakus spare/repair parts are intended only for vehicle repairs in order to restore their original functionality. Abakus spare/repair parts are used or sold to users only for the purpose of repairing vehicles to restore their original look and functionality and are not original/genuine/OE/OEM/OES replacement parts. Our products are delivered without instruction of installation. Installation of our product may only be carried out by trained specialist technicians in specific car repairs. Products supplied by us are exclusively intended for proper and appropriate use. The warranty may become invalid in the event of: improper installation or repair, unsuitable application or use, installation or repair made outside specialist car workshops. Warranty claims are lost if the vehicle is modified and used for motor sports, tuning or similar events (except our tuning parts which are described in TecDoc and on our price list). Warranty application should include complete documentation among others: chassis no., first registration, vehicle mileage, information about LPG installation, fault memory log, pictures, our QC (quality check) code, installation invoice, contact details of the car repair workshop performing the replacement or repair. Warranty application are available in our Client Panel system. Complaints may require supplementing data such as error memory logs. Incomplete documentation may result in rejection of the claim. Any damage caused during transport is not considered quality damage and will be considered on an individual basis.

• Fabrication Number: ECP-AU-042
• Manufacturer: NTY

• Cable Length [mm]: 410
• Number of pins: 3
• Weight [kg]: 0.1
• Warranty: 3 years warranty
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY
• Name: CE 17SKV511

• Length [mm]: 455
• Number of pins: 3
• Manufacturer: DELLO AUTOMEGA

• Number of pins: 3
• Connector Shape: D Shape
• Supplementary Article/Info 2: with cable
• Supplementary Article/Supplementary Info: with cable protection pipe, with holder, with seal
• Name: ANDUR, VŽNTVOLL
• Manufacturer: HAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Number of pins: 3
• Weight [kg]: 0.03
• Warranty: 3 years warranty
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY
• Name: CE 17SKV487

• Diameter [mm]: 26
• Number of pins: 2
• Supplementary Article/Info 2: with seal ring
• Spring Design: Retaining Spring
• Length [mm]: 20
• Housing Colour: blue
• Height [mm]: 57
• Weight [kg]: 0.02
• Colour: grey
• Number of connectors: 2
• Manufacturer: VEMO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Number of pins: 2
• Housing Colour: grey
• Manufacturer: FAE

• Length [mm]: 68
• Number of pins: 3
• Name: Andur,Nukkvollipositsioon
• Manufacturer: MAX

• Number of pins: 5
• Manufacturer: ABAKUS DEPO/LORO

General Information: The following information is for general and informational purposes only and does not constitute warranty terms. Warranty terms and conditions are available from our dealers and in our general terms and conditions of sale. Abakus spare/repair parts are intended only for vehicle repairs in order to restore their original functionality. Abakus spare/repair parts are used or sold to users only for the purpose of repairing vehicles to restore their original look and functionality and are not original/genuine/OE/OEM/OES replacement parts. Our products are delivered without instruction of installation. Installation of our product may only be carried out by trained specialist technicians in specific car repairs. Products supplied by us are exclusively intended for proper and appropriate use. The warranty may become invalid in the event of: improper installation or repair, unsuitable application or use, installation or repair made outside specialist car workshops. Warranty claims are lost if the vehicle is modified and used for motor sports, tuning or similar events (except our tuning parts which are described in TecDoc and on our price list). Warranty application should include complete documentation among others: chassis no., first registration, vehicle mileage, information about LPG installation, fault memory log, pictures, our QC (quality check) code, installation invoice, contact details of the car repair workshop performing the replacement or repair. Warranty application are available in our Client Panel system. Complaints may require supplementing data such as error memory logs. Incomplete documentation may result in rejection of the claim. Any damage caused during transport is not considered quality damage and will be considered on an individual basis.

• Required quantity: 1
• Voltage [V]: 12
• Number of pins: 3
• Sensor Type: Hall Sensor
• Supplementary Article/Info 2: without cable
• Housing Colour: black
• Manufacturer: BRM

Name: CZUJNIK POO½ENIA WAKA ROZRZ. VW TRANSPORTER 2,5TDI 04-

• Connector Shape: D Shape
• Supplementary Article/Info 2: without cable, with seal ring
• Number of pins: 3
• Manufacturer: TOPRAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Vehicle Identification Number (VIN) from: 7J-6-000 001
• Vehicle Identification Number (VIN) to: 7J-9-020 000
• Manufacturer Restriction: VAG
• Number of pins: 3
• Cable Length [mm]: 200
• Socket Width [mm]: 1.5
• Supplementary Article/Supplementary Info: with socket housing, with gaskets/seals
• Supplementary Article/Info 2: with pipe
• Contact surface: Gold-plated
• Cable Cross Section [mm²]: 0.75
• Temperature range from [°C]: -25
• Temperature range to [°C]: +140
• Cable insulation material: Silicone
• Plug housing design: Plug sleeve housing
• SVHC: No SVHC present!
• Name: Kaabli remondikomplekt, rattap””rete andur
• Manufacturer: HBE

• Housing Type: with housing
• Fabrication Number: EPP-AU-001
• Manufacturer: NTY

• Required quantity: 1
• Number of pins: 3
• Sensor Type: Inductive Sensor
• Supplementary Article/Info 2: with cable
• Housing Colour: black
• Manufacturer: BRM
• Additional information: 60329 NIS
• Lisainfo: 60329 NIS

Name: CZUJNIK POO½ENIA WAU KORB. VW TOUAREG (03-05), TRANSPORTER 2,5 TDI (03-10)

• General Information: hall sender camshaft
• Manufacturer: VIKA

• Number of connectors: 3
• Cable Length [mm]: 320
• Weight [kg]: 0.074
• Manufacturer: FEBI BILSTEIN

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Number of pins: 3
• Connector Shape: D Shape
• Cable Length [mm]: 330
• Sensor Type: Inductive Sensor
• for OE number: 070 907 319
• Name: Andur, v„ntvoll
• Manufacturer: MD

• Voltage [V]: 12
• Fabrication Number: EPP-AU-031

• Number of pins: 3
• Fitting Depth [mm]: 36
• Weight [kg]: 0.031
• Manufacturer: ERA

• Sensor Type: Hall Sensor
• Number of pins: 3
• Connector Shape: D Shape
• Supplementary Article/Info 2: without cable
• Weight [kg]: 0.03
• Name: Andur,Nukkvollipositsioon
• Manufacturer: VAL

• Engine Code: BNZ
• Number of pins: 2
• Supplementary Article/Info 2: with cable
• Manufacturer: METZGER

• Length [mm]: 68
• Width [mm]: 36
• Thickness [mm]: 20
• Number of connectors: 3
• Weight [kg]: 0.02
• Supplementary Article/Info 2: with seal ring
• Name: ANDUR,NUKKVOLLIPOSITSIOON
• Manufacturer: FEB

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Length [mm]: 68
• Width [mm]: 36
• Thickness [mm]: 20
• Number of connectors: 3
• Supplementary Article/Info 2: with seal ring
• Name: SW 30 94 4360
• Manufacturer: SWAG

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Sensor Type: Inductive Sensor
• Number of pins: 3
• Connector Shape: D Shape
• Supplementary Article/Info 2: with cable
• Weight [kg]: 0.1
• Name: Andur, v„ntvoll
• Manufacturer: VAL

• Engine Code: AXD
• for OE number: 28906461
• Number of pins: 5
• Voltage [V]: 12
• Manufacturer: DELLO AUTOMEGA

• Engine Code: AXD
• for OE number: 038906461C
• Number of pins: 5
• Voltage [V]: 12
• Manufacturer: DELLO AUTOMEGA

• Number of pins: 5
• Housing Type: with housing
• Housing material: Plastic
• Voltage [V]: 12
• Fabrication Number: EPP-AU-024
• Manufacturer: NTY

• Engine Code: AXD
• Housing Type: with housing
• Number of pins: 5
• Manufacturer: JP GROUP
• Lisainfo: Air meter
• Additional information: Air meter

• Engine Code: AXD
• Voltage [V]: 12
• Name: Ohumassimootja
• Manufacturer: MAX

• Construction Year from: 06.2006
• Weight [kg]: 0.29
• Warranty: 3 years warranty
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY
• Name: CE 07SKV157

• Engine Code: AXD
• Recommended additional repairs: Air Filter
• Name: OHUMASSIMOOTJA
• Manufacturer: MAX

• Engine Code: AXD
• Number of pins: 5
• Voltage [V]: 12
• Name: OHUMASSIMOOTJA
• Manufacturer: MAX

• Engine Code: AXD
• for OE number: 1209109
• Manufacturer: DELLO AUTOMEGA

• Engine Code: AXD, AXD,BNZ
• Voltage [V]: 12
• Housing Type: with housing
• Number of pins: 5
• Weight [kg]: 0.32
• Operating Mode: Electric
• Warranty: 3 years warranty
• Always compare old and new part (in particular OE No.):
• Name: CE 07SKV083
• Manufacturer: ESEN SKV

• for OE number: 03G 906 461 C
• Manufacturer: KAMOKA

• Required quantity: 1
• Number of pins: 3
• Supplementary Article/Info 2: for camshaft, without cable
• Sensor Type: Hall Sensor
• Number of connectors: 3
• Rated Voltage [V]: 12
• Fitting Depth [mm]: 36
• Housing Colour: black
• Connector Shape: D Shape
• Resistor [kOhm]: 34
• Weight [kg]: 0.018
• Manufacturer: VEMO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Housing Type: with housing
• Number of pins: 5
• Housing material: Plastic
• Connector Shape: D Shape
• Number of mounting bores: 2
• Supplementary Article/Info 2: with integrated grille
• Recommended additional repairs: Air Filter
• Article number of recommended accessories: 113 883
• New Part:
• Used part return not required:
• Manufacturer: TOPRAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Engine Code: AXD
• Number of pins: 5
• Manufacturer: MEAT&DORIA

• Engine Code: BNZ
• Voltage [V]: 12
• Housing Type: with housing
• Name: Ohumassimootja
• Manufacturer: MAX

• Recommended additional repairs: Air Filter
• General Information: air mass meter
• Manufacturer: VIKA

• Engine Code: AXD
• Mounting Type: Bolted
• Number of pins: 5
• Assy./disassy. by qualified personnel required!:
• Name: Ohumassimootja
• Manufacturer: HEL

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Supplementary Article/Supplementary Info: without suction pipe
• Engine Code: AXD
• Warranty: 5 years warranty
• General Information: Sold in Hueco brand: printing and packaging
• Name: OHUMASSIMOOTJA
• Manufacturer: HUC

Technical Information: Designed as plug-in sensor: Original tube is used furthermore. Look out for contamination!

• Warranty: 5 years warranty
• Manufacturer: HITACHI

• Lambda Sensor: Lambda Sensor
• Weight [kg]: 0.22
• Warranty: 3 years warranty
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY
• Name: CE 09SKV420

• Engine Code: BNZ
• Construction Year from: 06.2006
• Lambda Sensor: Regulating Probe
• Fitting Position: before catalytic converter
• Number of circuits: 5
• Overall Length [mm]: 1,215
• Lisainfo: Lambda Sensor
• Additional information: Lambda Sensor

• Engine Code: AXD
• Housing Type: with housing
• Number of pins: 5
• Plug Type: Male
• Housing Colour: black
• Voltage [V]: 12
• Recommended additional repairs: Air Filter
• Name: OHUMASSIMOOTJA
• Manufacturer: DLP

• Operating Mode: Electric
• Name: OHUMASSIMOOTJA
• Manufacturer: MAG
• Additional information: 213719641019 MAG
• Lisainfo: 213719641019 MAG

• Housing Type: with housing
• Housing material: PBT, GRP (Glass fibre Reinforced Plastic)
• Number of pins: 5
• Connector Shape: D Shape
• Number of mounting bores: 2
• Supplementary Article/Info 2: without seal ring, with integrated grille
• Recommended additional repairs: Air Filter
• Article number of recommended accessories: 113 883
• Fitting Position: Air Filter Housing
• Used part return not required:
• New Part:
• Manufacturer: TOPRAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Construction Year from: 06.2006
• Lambda Sensor: Regulating Probe, Heated
• Resistor [Ohm]: 4.9
• Length [mm]: 1,215
• Conductor Number: 5
• Number of circuits: 5
• Cable Length [mm]: 1,215
• Manufacturer: MAGNETI MARELLI

• Supplementary Article/Supplementary Info: without suction pipe
• Engine Code: AXD
• General Information: Sold in Hitachi brand: printing and packaging
• Manufacturer: HUCO

Technical Information: Designed as plug-in sensor: Original tube is used furthermore. Look out for contamination!

• Engine Code: AXD
• for article number: V10-72-0959, V10-72-0958
• Housing Type: without housing
• Number of pins: 5
• New Part:
• Used part return not required:
• Recommended additional repairs: Air Filter
• Alternatively:
• Weight [kg]: 0.09
• Manufacturer: VEMO GERMANY