Assembly categories
Filters Brake System Axle Steering Cooling / AC Electrics Towbar/Accessories Transmission Exhaust System Body Ignition Engine Windscreen Cleaning Lights Fuel Supply Interior ServiceProduct
Description
In stock
Price
(incl. VAT)
- Operating voltage [V]: 12
- Rated Power [W]: 480
- Rated current [A]: 40
- Combi Switch Function: Normally Open Contact
- Number of pins: 4
-
Lisainfo: Relay,
12 Volt, 40 Amp -
Additional information: Relay,
12 Volt, 40 Amp
Relay function: Terminal 75, Interior Blower, Suction pipe pre-heating, Sunroof, Pump, fuel pre-supply, Start-stop system, Magnetic clutch, Surge protection, Battery main switch, Engine control unit, Normally open contact, X contact relief, Fan, engine cooling, Electric booster heater, Secondary Air System, Water pump after-run, Rear window wiper, heater/air conditioning, Clamp 15, Fuel Pump, Window Regulator, Heated windscreen, Heated rear window, Parking Heater
- Number of connectors: 4
Lisainfo: Relay for fuel pump and intake manifold heating, 12 Volt, 40 Amp Additional information: Relay for fuel pump and intake manifold heating, 12 Volt, 40 Amp
- for OE number: 1K0 951 253
- Current Strength [A]: 30
- Voltage [V]: 12
- Number of pins: 4
- Relay function: Central electrics
-
Temperature range from [°C]: -
40 - Temperature range to [°C]: 100
- Resistor [Ohm]: 27
- Manufacturer: BOSCH
- Name: BS 0332011007
- Pinge [V]: 12
- Pistikkontaktide arv: 4
- Kasutuspinge 12V: 40A
- Manufacturer: AIC
Üldine informatsioon: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.
- Rated Voltage [V]: 12
-
Relay function: Pre-
glow device -
Lisainfo: Relay,
glowing, 12 Volt, 70 Amp -
Additional information: Relay,
glowing, 12 Volt, 70 Amp
- for OE number: 4H0 951 253 C
- Current Strength [A]: 30
- Voltage [V]: 12
- Number of pins: 5
- Relay function: Normally open contact
- Protection Type (IP Code): IP5K4
-
Temperature range from [°C]: -
40 - Temperature range to [°C]: 100
- Resistor [Ohm]: 16
- Manufacturer: BOSCH
- Name: BS 0332201107
- Operating voltage [V]: 12
- Rated Power [W]: 180
- Rated current [A]: 15
- Combi Switch Function: Normally Open Contact
- Resistor [Ohm]: 70
- Number of pins: 4
- Lisainfo: Multifunctional Relay
- Additional information: Multifunctional Relay
Relay function: Sunroof, Fuel Pump, Tailgate, Terminal 30, Gear Lever, Licence plate light, Engine control unit, Normally open contact
- Pinge [V]: 12
- Nimivool [A]: 40
- Pistikkontaktide arv: 4
- Lüliti funktsioon: Lukustaja
- Manufacturer: AIC
Üldine informatsioon: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.
- Pistikkontaktide arv: 4
- Pinge [V]: 12
- Voolutugevus (A): 70
- Relee funktsioon: Töökontakt
- Manufacturer: AIC
Üldine informatsioon: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.
- General Information: relay
- Manufacturer: BORSEHUNG
-
Relay Number: 53,
373 - Voltage [V]: 12
- Capacity at 12V: 40A
- Combi Switch Function: Normally Open Contact
- Number of pins: 4
-
Temperature range from [°C]: -
40 - Temperature range to [°C]: 125
- Weight [g]: 24
- Inductive Load [A]: 15
- Capacitive Load [A]: 5
- Rated current [A]: 40
- Ohmic Load [A]: 40
- Quantity: 1
- Assy./disassy. by qualified personnel required!:
- Name: HE 4RA933332451
- Manufacturer: HELLA
Relay function: Washer Fluid Pump, headlight cleaning, Auxiliary Water Pump, Comfort Equipment Variant (trim package), park distance control, ABS, Low Beam, High Beam, Heated rear window, ESP, Window Regulator, Starter, Klaxon, Air Conditioning, Light switch, Fan, heater/air conditioning, Interior Blower, Clamp 15, Daytime Running Light, Convertible Top Hydraulics, Central Locking, ABS recovery pump, Exterior Rearview Mirror Adjustment, Heatable exterior mirror, Electric booster heater, Interior Lighting, Clamp 15R, Clamp 87, Fuel Pump, Lambda Sensor, engine cooling, Front Fog Light, Windscreen wiper, Windscreen wiper rest heating, Sunroof, Secondary Air System, Seat Heating Brief Information: *** HELLA Electronics OE competence for over 60 years.
- General Information: relay
- Manufacturer: BORSEHUNG
- Voltage [V]: 12
- Weight [kg]: 0.025
- Number of connectors: 4
- Current Strength [A]: 30
- Supplementary Article/Supplementary Info: with holder
- General Information: relay
- Manufacturer: BORSEHUNG
- Garantii: 3 aastat garantii
-
Kaal (kg): 0,
04 - Oluline on võrrelda vana uue osaga (eriti OE-numbrit):
- Name: CE 96SKV005
- Manufacturer: ESEN SKV
- General Information: relay
- Manufacturer: BORSEHUNG
- General Information: relay
- Manufacturer: BORSEHUNG
- Engine Code: BMS
-
Relay Number: 67,
80, 167 - Number of connectors: 4
- Weight [kg]: 0.035
- Manufacturer: FEBI BILSTEIN
General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.
- Pistikkontaktide arv: 4
- Pinge [V]: 12
- Nimivool [A]: 15
- Lüliti funktsioon: Lukustaja
- Manufacturer: AIC
Üldine informatsioon: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.
- General Information: relay
- Manufacturer: BORSEHUNG
-
Relay function: Pre-
glow device, X contact relief - Rated Voltage [V]: 12
- Number of connectors: 4
- Current Strength [A]: 70
- Relay Number: 644
- General Information: relay
- Manufacturer: BORSEHUNG
- for OE number: 2D0 959 145 A
- Current Strength [A]: 15
- Voltage [V]: 12
- Relay function: Normally open contact
- Manufacturer: BOSCH
- Voltage [V]: 12
- Weight [kg]: 0.01
- Number of connectors: 5
- General Information: relay
- Manufacturer: BORSEHUNG
- Weight [kg]: 0.035
- Fitting Position: Engine Compartment
- Manufacturer: VEMO
General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.
- Engine Code: BMS
- Current Strength [A]: 40
-
Relay function: Terminal 30,
Clamp 87 - Rated current [A]: 40
- Weight [kg]: 0.04
- Manufacturer: VEMO
General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.
-
Vehicle Identification Number (VIN) from: 9N-
5- 500 001 - Current Strength [A]: 15
-
Relay function: Terminal 30,
Clamp 87 - Number of pins: 4
- Voltage [V]: 12
- Colour: black
- Weight [kg]: 0.033
- Manufacturer: VEMO
General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.
- Weight [kg]: 0.04
- Manufacturer: VEMO
General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.
- Voltage [V]: 12
- Current Strength [A]: 30
- Number of pins: 4
- Relay Number: 449
- Supplementary Article/Info 2: with resistor
- Housing Colour: black
- Manufacturer: VEMO
Relay function: Trumpet Horns, Low Beam, Interior Blower, Starter, Fuel Pump, Radiator Fan Overrun General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.
- Nominaalpinge (V): 12
-
Seerianumber: CSW-
VW- 004 -
Name: NTY CSW-
VW- 004 - Manufacturer: NTY
Relee funktsioon: Jahutusventilaatori ülejooks, Ventilaator, radiaator
Tavatellimus saadetakse E, K ja R kell 14:00. Kaup saabub kuni 3'e tööpäevaga. Tavatellimusse lähevad ainult positiivse laojäägiga tooted. Lisaks tavatellimusele on võimalik tellida ka Express kulleriga (24h). Kulleri hinda täpsusta 6 599 702, malva@lakiauto.ee.
-
Vehicle Identification Number (VIN) from: 9N-
2- 000 001 - Fitting Position: engine sided
-
Relay Number: 15/
109 -
Supplementary Article/Info 2: Mini Relay,
with resistor - Supplementary Article/Supplementary Info: without holder
- Protection Type (IP Code): IP54
- Voltage [V]: 12
-
Temperature range from [°C]: -
40 - Temperature range to [°C]: +70
- Colour: black
- Inductive Load [A]: 15
- Capacitive Load [A]: 15
- Ohmic Load [A]: 15
- Number of pins: 4
- Wiring Diagramme: X
- Combi Switch Function: Normally Open Contact
- Plug Type ID: X
- Assy./disassy. by qualified personnel required!:
- Name: HE 4RA007507081
- Manufacturer: HELLA
Relay function: Central electrics, Comfort Equipment Variant (trim package), park distance control, ABS, Low Beam, High Beam, Heated rear window, ESP, Window Regulator, Starter, Klaxon, Air Conditioning, Light switch, Fan, heater/air conditioning, Interior Blower, Clamp 15, Daytime Running Light, Convertible Top Hydraulics, Central Locking, ABS recovery pump, Exterior Rearview Mirror Adjustment, Heatable exterior mirror, Electric booster heater, Interior Lighting, Clamp 15R, Clamp 87, Fuel Pump, Lambda Sensor, engine cooling, Front Fog Light, Windscreen wiper, Windscreen wiper rest heating, Sunroof, Secondary Air System, Seat Heating Brief Information: *** HELLA Electronics OE competence for over 60 years.
- Engine Code: BMS
- Voltage [V]: 12
- Assy./disassy. by qualified personnel required!:
- Manufacturer: HELLA
Brief Information: *** HELLA Electronics OE competence for over 60 years.
-
Number of Cylinders: 5,
4 - Voltage [V]: 12
- Manufacturer: BERU
-
Seerianumber: EZP-
VW- 003 -
Name: NTY EZP-
VW- 003 - Manufacturer: NTY
Tavatellimus saadetakse E, K ja R kell 14:00. Kaup saabub kuni 3'e tööpäevaga. Tavatellimusse lähevad ainult positiivse laojäägiga tooted. Lisaks tavatellimusele on võimalik tellida ka Express kulleriga (24h). Kulleri hinda täpsusta 6 599 702, malva@lakiauto.ee.
- Vehicle Equipment: for vehicles with air conditioning
- Voltage [V]: 12
- Current Strength [A]: 60
- Number of connectors: 10
- Weight [kg]: 0.172
- Fitting Position: Engine Compartment
- Manufacturer: VEMO
General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.
- Engine Code: BMS
- Voltage [V]: 12
- Number of Cylinders: 3
- Guarantee: 5 years guarantee
- Name: HU 132138
-
Manufacturer: HUECO /
HITACHI
General Information: Recommendation: Use grease for glow plugs 134100 = 10g. or 134101 = 100g., see accessory lists.
Laki Auto universal products
TecDoc catalogue for cars
TecDoc catalogue for trucks