• Engine Number to: 562757
• Fitting Position: transmission sided
• Inner Diameter [mm]: 85
• Outer Diameter [mm]: 105
• Width 1 [mm]: 9
• Width 2 [mm]: 11
• Housing Type: with housing
• Lisainfo: Seal flange for crankshaft
• Additional information: Seal flange for crankshaft

• Required quantity: 1
• Fitting Position: frontal sided
• Engine Number to: 562757
• Inner Diameter [mm]: 32
• Outer Diameter [mm]: 47
• Width [mm]: 10
• SVHC: No SVHC present!
• Manufacturer: INA
• Name: LU 413009310

• Fitting Position: frontal sided
• Fabrication Number: NUP-VW-016
• for OE number: 036103085H
• Inner Diameter 1 [mm]: 32
• Outer Diameter 1 [mm]: 42
• Material: FPM (fluoride rubber)
• Dust Cover: with dust lip
• Swirl Type: Right-hand Twist
• Manufacturer: NTY

• Engine Code: AEE
• Engine Number to: -> 574655
• Fitting Position: Front
• Height 1 [mm]: 10
• Outer Diameter 1 [mm]: 47
• Inner Diameter 1 [mm]: 32
• Material: FPM (fluoride rubber)
• for OE number: 026103085D
• Swirl Type: Alternating Twist
• Dust Cover: with dust lip
• Name: VOLLI RONGASTIHEND, NUKKVOLL
• Manufacturer: COT
• Additional information: 12012709
• Lisainfo: 12012709

• Fitting Position: frontal sided
• Engine Number to: AEE 562 757
• Inner Diameter [mm]: 32
• Outer Diameter [mm]: 47
• Height [mm]: 10
• Radial Shaft Seal Design: ASW
• Swirl Type: Alternating Twist
• Material: FPM (fluoride rubber)/ACM (polyacrylate rubber)
• Dust Cover: with dust lip
• Alternative Repair Kit: 325.156
• Manufacturer: ELRING
• Lisainfo: 325.155 ELR
• Additional information: 325.155 ELR

• Fitting Position: frontal sided
• Engine Number to: AEE 562 757
• Engine Code: AEE
• Material: FPM (fluoride rubber)
• Inner Diameter [mm]: 32
• Outer Diameter [mm]: 47
• Height [mm]: 10
• Radial Shaft Seal Design: A SL
• Swirl Type: Alternating Twist
• Name: VOLLI RONGASTIHEND, NUKKVOLL
• Manufacturer: REI
• Lisainfo: 81-19299-10
• Additional information: 81-19299-10

• Installatsiooni pool: stirnseitig
• Siseläbimõõt [mm]: 32
• Välisläbimõõt [mm]: 47
• Jämedus/Tugevus (mm): 10
• Üldine informatsioon: Oil seal for camshaft; 47*10*32
• Manufacturer: VIKA

• Engine Code: AEE
• Engine Number to: 630 000
• Fitting Position: frontal sided, transmission sided
• Height [mm]: 11
• Material: FPM (fluoride rubber)
• Inner Diameter [mm]: 85
• Outer Diameter [mm]: 105
• Swirl Type: Left-hand Twist
• Dust Cover: with dust lip
• Manufacturer: DELLO AUTOMEGA

• Thickness [mm]: 10
• for OE number: 068 103 085 E
• Fitting Position: frontal sided
• Inner Diameter [mm]: 32
• Outer Diameter [mm]: 47
• Manufacturer: VAICO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Inner Diameter [mm]: 32
• Outer Diameter [mm]: 47
• Height [mm]: 10
• Dust Cover: with dust lip
• Swirl Type: Alternating Twist
• Fitting Position: frontal sided
• Material: FPM (fluoride rubber)/ACM (polyacrylate rubber)
• Manufacturer: TOPRAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Engine Code: AEE
• Fitting Position: frontal sided
• Inner Diameter [mm]: 32
• Outer Diameter [mm]: 47
• Height [mm]: 10
• Swirl Type: Alternating Twist
• Name: VOLLI RONGASTIHEND, NUKKVOLL
• Manufacturer: AJU

• Fitting Position: frontal sided
• Engine Number to: AEE 562 757
• Inner Diameter [mm]: 32
• Outer Diameter [mm]: 47
• Height [mm]: 10
• Radial Shaft Seal Design: ASW
• Swirl Type: Alternating Twist
• Material: FPM (fluoride rubber)
• Dust Cover: with dust lip
• Alternative Repair Kit: 325.155
• Manufacturer: ELRING

• Engine Code: AEE
• Engine Number from: 574656 ->
• Fitting Position: frontal sided
• Height 1 [mm]: 8
• Outer Diameter 1 [mm]: 42
• Inner Diameter 1 [mm]: 32
• Material: FPM (fluoride rubber)
• for OE number: 036103085H
• Swirl Type: Right-hand Twist
• Dust Cover: with dust lip
• Name: VOLLI RONGASTIHEND, NUKKVOLL
• Manufacturer: COT

• Fitting Position: frontal sided
• Engine Number from: AEE 562 758
• Engine Code: AEE
• Material: FPM (fluoride rubber)
• Inner Diameter [mm]: 32
• Outer Diameter [mm]: 42
• Height [mm]: 6
• Radial Shaft Seal Design: A SL
• Swirl Type: Right-hand Twist
• Height 1 [mm]: 7
• Name: VOLLI RONGASTIHEND, NUKKVOLL
• Manufacturer: REI

• Fitting Position: frontal sided
• Engine Number from: AEE 562 758
• Inner Diameter [mm]: 32
• Outer Diameter [mm]: 42
• Height [mm]: 6
• Radial Shaft Seal Design: AW/BS
• Swirl Type: Right-hand Twist
• Material: FPM (fluoride rubber)
• Dust Cover: with dust lip
• Manufacturer: ELRING

• Engine Number to: 630000
• Fitting Position: transmission sided
• Inner Diameter [mm]: 85
• Outer Diameter [mm]: 105
• Width [mm]: 11
• Name: Volli rongastihend, V„ntvoll
• Manufacturer: DRM

• Fitting Position: transmission sided
• Height [mm]: 12
• Outer Diameter [mm]: 105
• Inner Diameter [mm]: 85
• Material: NBR (nitrile butadiene rubber)
• Manufacturer: BGA

• Inner Diameter [mm]: 85
• Outer Diameter [mm]: 105
• Height [mm]: 11
• Dust Cover: with dust lip
• Swirl Type: Left-hand Twist
• Material: FPM (fluoride rubber)
• Fitting Position: transmission sided
• Alternative Repair Kit: 105 753
• Manufacturer: TOPRAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Fitting Position: Pulley side
• Manufacturer: CORTECO USZCZELNIACZE

• Fitting Position: transmission sided
• Engine Number to: AEE 562 757
• Engine Code: AEE
• Material: FPM (fluoride rubber)
• Inner Diameter [mm]: 85
• Outer Diameter [mm]: 105
• Height [mm]: 11
• Radial Shaft Seal Design: A SL
• Swirl Type: Left-hand Twist
• Height 1 [mm]: 9
• Name: VOLLI RONGASTIHEND, VŽNTVOLL
• Manufacturer: REI
• Lisainfo: 81-23708-40
• Additional information: 81-23708-40

• Fitting Position: transmission sided
• Engine Number to: AEE 630 000
• Inner Diameter [mm]: 85
• Outer Diameter [mm]: 105
• Height [mm]: 11
• Radial Shaft Seal Design: ASW
• Swirl Type: Left-hand Twist
• Material: FPM (fluoride rubber)
• Dust Cover: with dust lip
• Alternative Repair Kit: 829.056
• Manufacturer: ELRING
• Lisainfo: 342.093 ELR
• Additional information: 342.093 ELR

• Fitting Position: Axle beam
• General Information: Oil seal for camshaft
• Manufacturer: BORSEHUNG

• Engine Number to: AEE 630 000
• Quantity per packing unit: 5
• Thickness [mm]: 11
• Inner Diameter [mm]: 85
• Outer Diameter [mm]: 105
• Fitting Position: transmission sided
• Manufacturer: VAICO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Engine Code: AEE
• Fitting Position: transmission sided
• Inner Diameter [mm]: 85
• Outer Diameter [mm]: 105
• Height [mm]: 12
• Manufacturer: AJUSA

• Supplementary Article/Info 2: with flange
• Fitting Position: transmission sided
• Fabrication Number: NUP-VW-006
• Manufacturer: NTY

• Fitting Position: transmission sided, Rear
• Engine Number from: AEE562758
• Engine Code: AEE
• Supplementary Article/Info 2: with flange
• Name: VOLLI RONGASTIHEND, VŽNTVOLL
• Manufacturer: MAX

• Engine Number to: 562757
• Fitting Position: transmission sided
• Supplementary Article/Info 2: with flange
• Outer Diameter [mm]: 111
• Inner Diameter [mm]: 85
• Height [mm]: 16
• Manufacturer: DELLO AUTOMEGA

• Fitting Position: transmission sided
• Housing Type: with housing
• Housing material: Cast Aluminium
• Alternative Repair Kit: 101 407
• Sealing lip material: PTFE (polytetrafluoroethylene)
• Manufacturer: TOPRAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Fitting Position: transmission sided
• Engine Code: AEE
• Material: PTFE (polytetrafluoroethylene)
• for OE number: 038103171
• Manufacturer: FAI

• Engine Code: AEE
• Fitting Position: transmission sided
• Supplementary Article/Info 2: with mounting sleeve
• Height 1 [mm]: 11
• Outer Diameter 1 [mm]: 105
• Inner Diameter 1 [mm]: 85
• Material: FPM (fluoride rubber)
• for OE number: 068103071F
• Swirl Type: Alternating Twist
• Name: VOLLI RONGASTIHEND, VŽNTVOLL
• Manufacturer: COT

• Fitting Position: transmission sided
• Engine Number to: AEE 630 000
• Inner Diameter [mm]: 85
• Outer Diameter [mm]: 105
• Height [mm]: 11
• Radial Shaft Seal Design: ASW
• Swirl Type: Left-hand Twist
• Material: FPM (fluoride rubber)
• Dust Cover: with dust lip
• Supplementary Article/Info 2: with mounting sleeve
• Manufacturer: ELRING

• Installatsiooni pool: kastipoolselt
• Kaal (kg): 0,17
• Siseläbimõõt [mm]: 85
• vajaminev tükihulk: 1
• Piirangutega toode/piirangu info 2: koos flantsiga
• Üldine informatsioon: sealing flang; rear
• Manufacturer: VIKA

• Engine Code: AEE
• Quantity per packing unit: 5
• Fitting Position: transmission sided
• Inner Diameter [mm]: 85
• Manufacturer: VAICO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Engine Number from: 630001
• Fitting Position: transmission sided
• Inner Diameter [mm]: 85
• Radial Shaft Seal Design: SP
• Housing Type: with housing
• Name: Volli rongastihend, V„ntvoll
• Manufacturer: DRM

• Outer Diameter [mm]: 47
• Thickness [mm]: 10
• Inner Diameter [mm]: 32
• Fitting Position: transmission sided
• Manufacturer: VAICO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Fitting Position: transmission sided
• Engine Number from: AEE 562 758
• Engine Code: AEE
• Supplementary Article/Info 2: with flange
• Name: VOLLI RONGASTIHEND, VŽNTVOLL
• Manufacturer: REI

• Fitting Position: transmission sided
• Engine Number from: AEE 630 001
• Inner Diameter [mm]: 85
• Radial Shaft Seal Design: SP
• Swirl Type: Left-hand Twist
• Housing Type: with housing
• Supplementary Article/Info 2: with mounting sleeve
• Observe mounting information:
• Manufacturer: ELRING
• Lisainfo: 804.850 ELR
• Additional information: 804.850 ELR

Material: PTFE (polytetrafluoroethylene)/ACM (polyacrylate rubber) Installation Information: Mounting dry and without any additional oil and grease

• Quantity: 1
• Installatsiooni pool: kastipoolselt
• Kaal (kg): 0,17
• Siseläbimõõt [mm]: 85
• vajaminev tükihulk: 1
• Piirangutega toode/piirangu info 2: koos flantsiga
• Üldine informatsioon: sealing flang; rear
• Manufacturer: VIKA

• Engine Code: AEE
• Fitting Position: transmission sided
• Supplementary Article/Info 2: with mounting sleeve
• Height 1 [mm]: 15.7
• Outer Diameter 1 [mm]: 131
• Outer Diameter 2 [mm]: 152
• Inner Diameter 1 [mm]: 85
• Material: PTFE (polytetrafluoroethylene)
• for OE number: 028103171B
• Swirl Type: Alternating Twist
• Name: VOLLI RONGASTIHEND, VŽNTVOLL
• Manufacturer: COT