• Fitting Position: Front Axle Left, Lower
• Control/Trailing Arm Type: Control Arm
• Manufacturer: JP GROUP
• Lisainfo: Track Control Arm
• Additional information: Track Control Arm

• Fitting Position: Front Axle Right, Lower
• Control/Trailing Arm Type: Control Arm
• Manufacturer: JP GROUP
• Lisainfo: Track Control Arm
• Additional information: Track Control Arm

• Fitting Position: Front Axle Right, Front Axle Left
• Required quantity: 1
• Block Separation:
• Control/Trailing Arm Type: Control Arm
• for article number: 58011902 / 58012001
• Guarantee: 3 years guarantee or up to 75,000km
• Manufacturer: METZGER

• Fitting Position: Front Axle Right, Front Axle Left
• replacement in pairs recommended:
• Required quantity: 2
• Manufacturer: MEYLE
• Lisainfo: 1006100061
• Additional information: 1006100061

• Fitting Position: Front Axle Right
• Control/Trailing Arm Type: Control Arm
• Supplementary Article/Info 2: without ball joint
• Fabrication Number: ZWD-VW-039A
• paired article number: ZWD-VW-038A

• Fitting Position: Front Axle Left
• Control/Trailing Arm Type: Control Arm
• Supplementary Article/Info 2: without ball joint
• Fabrication Number: ZWD-VW-038A
• paired article number: ZWD-VW-039A

• Fitting Position: Front Axle Left
• Axle alignment required after fitting:
• paired article number: V10-3908
• for OE number: 1J0 407 151 C
• Control/Trailing Arm Type: for control arm
• Quantity Unit: Set
• Supplementary Article/Supplementary Info: with accessories
• Weight [kg]: 0.84
• Manufacturer: VAICO

Supplementary Article/Info 2: with rubber mount, with ball joint, with lock screw set General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Axle alignment required after fitting:
• paired article number: V10-3907
• Control/Trailing Arm Type: for control arm
• Supplementary Article/Supplementary Info: with accessories
• Fitting Position: Front Axle Right
• Quantity Unit: Set
• Weight [kg]: 0.841
• Manufacturer: VAICO

Supplementary Article/Info 2: with rubber mount, with ball joint, with lock screw set General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Control/Trailing Arm Type: Control Arm
• Fitting Position: Lower, Front Axle Left, Front Axle Right
• Material: Sheet Steel
• Name: Control arm left=right
• Quality class: PJ

Lisainfo: "Tootja: SRL
AUDI A3 96-99
(kvaliteediklass: PJ)" Additional information: "Tootja: SRL
AUDI A3 96-99
(kvaliteediklass: PJ)"

• Fitting Position: Front Axle, both sides, Lower
• Control/Trailing Arm Type: Control Arm
• Manufacturer: DENCKERMANN ZAWIESZENIE

• Fitting Position: Front Axle Left, Front Axle Right, Lower
• Control/Trailing Arm Type: Control Arm
• Manufacturer: JP GROUP
• Lisainfo: Wishbone, front
• Additional information: Wishbone, front

• Fitting Position: Front Axle Right, Lower
• Control/Trailing Arm Type: Control Arm
• Cone Size [mm]: 18
• Manufacturer: DELLO AUTOMEGA

• Fitting Position: Lower, Front Axle Left, Front Axle Right
• Control/Trailing Arm Type: Control Arm
• Manufacturer: GSP

• Control/Trailing Arm Type: Control Arm
• Base body material: Steel
• Fitting Position: Rear Axle Right, Rear Axle Left
• Net weight [kg]: 1,436
• Diameter [mm]: 12.2
• Length [mm]: 517
• Diameter 1 [mm]: 12.2
• Supplementary Article/Info 2: without ball joint
• Name: OMG G41.2519/S
• Manufacturer: OMG

• Control/Trailing Arm Type: Control Arm
• Fabrication Number: ZWD-VW-038
• paired article number: ZWD-VW-039
• Manufacturer: NTY

Fitting Position: Front Axle Left, Front Axle, outer, Left, Right, Lower

• Control/Trailing Arm Type: Control Arm
• Fabrication Number: ZWD-VW-039
• paired article number: ZWD-VW-038
• Manufacturer: NTY

Fitting Position: Front Axle Right, Front Axle, outer, Left, Right, Lower

• Control/Trailing Arm Type: Control Arm
• Base body material: Steel
• Fitting Position: Front Axle Right, Front Axle Left
• Net weight [kg]: 3.06
• Diameter [mm]: 12.5
• Diameter 1 [mm]: 12.5
• Supplementary Article/Info 2: without ball joint
• Name: OMG G40.3598/S
• Manufacturer: OMG

• for OE number: 1J0 407 151 B
• Fitting Position: Front Axle both sides
• Control/Trailing Arm Type: Control Arm
• Manufacturer: TRUCKTEC AUTOMOTIVE

• Fitting Position: Front Axle, Left, Right, Lower
• Material: Sheet Steel
• Control/Trailing Arm Type: Trailing Arm
• Supplementary Article/Info 2: without ball joint
• Length [mm]: 420
• Width [mm]: 390
• Height [mm]: 55
• Manufacturer: DELPHI
• Name: DE TC2010

• Fitting Position: Front Axle Left, Lower Front Axle
• Control/Trailing Arm Type: Control Arm
• Length [mm]: 276.4
• Inner Diameter 1 [mm]: 12.2
• paired article number: TRC0124
• Supplementary Article/Info 2: with ball joint
• Manufacturer: BGA

• Fitting Position: Front Axle Right, Lower
• Control/Trailing Arm Type: Control Arm
• Cone Size [mm]: 15
• paired article number: 9050142
• Manufacturer: KAMOKA

• Control/Trailing Arm Type: Control Arm
• Fitting Position: Front Axle
• Inner Diameter [mm]: 12
• Name: ALT 79463AL
• Manufacturer: ALTE AUTOMOTIVE

• Name: Control arm left=right
• Quality class: PJ

Lisainfo: "Tootja: TEKNOROT
A.A3/GOLFIV/OCT/TOL.
(kvaliteediklass: PJ)"

• Fitting Position: Front Axle Right, Lower
• Control/Trailing Arm Type: Control Arm
• Material: Sheet Steel
• paired article number: 20-01071-2
• Weight [kg]: 3.49
• Name: DY 20-01071-1
• Manufacturer: DYS

• Fitting Position: Front Axle Left, Lower
• Control/Trailing Arm Type: Control Arm
• Material: Sheet Steel
• paired article number: 20-01071-1
• Weight [kg]: 3.49
• Name: DY 20-01071-2
• Manufacturer: DYS

• Fitting Position: Lower, Front Axle both sides
• Required quantity: 2
• Control/Trailing Arm Design: Triangular Control Arm
• paired article number: VKDS 321004
• Hole Pitch 1/ Hole Pitch 2: 276,4
• Control/Trailing Arm Type: Control Arm
• Supplementary Article/Info 2: without ball joint
• Manufacturer: SKF
• Name: SK VKDS321004

• Control/Trailing Arm Type: Control Arm
• Quantity Unit: Set
• Fitting Position: Lower, Front Axle Left
• Material: Sheet Steel
• Name: Control arm left
• Quality class: PJ

Lisainfo: "Tootja: SRL
AUDI A3 96-99
(kvaliteediklass: PJ)" Additional information: "Tootja: SRL
AUDI A3 96-99
(kvaliteediklass: PJ)"

• Control/Trailing Arm Type: Control Arm
• Quantity Unit: Set
• Fitting Position: Lower, Front Axle Right
• Material: Sheet Steel
• Name: Control arm right
• Quality class: PJ

Lisainfo: "Tootja: SRL
AUDI A3 96-99
(kvaliteediklass: PJ)" Additional information: "Tootja: SRL
AUDI A3 96-99
(kvaliteediklass: PJ)"

• Fitting Position: Front Axle Right
• Steering: with tie rod ends
• Control/Trailing Arm Type: Control Arm
• Manufacturer: VIKA

General Information: Wishbone arm for lower control;front right;with ball

• paired article number: 19822
• Material: Sheet Steel
• Control/Trailing Arm Type: Control Arm
• Fitting Position: Front Axle Left, Lower
• Weight [kg]: 3.5
• Supplementary Article/Supplementary Info: with bearings, with lock nuts
• Supplementary Article/Info 2: with ball joint
• Manufacturer: FEBI BILSTEIN

Technical Information: Please tighten the mounting bolts with the wheels on the ground. General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Fitting Position: Front Axle Left, Lower
• Control/Trailing Arm Type: Control Arm
• Cone Size [mm]: 15
• paired article number: 9050143
• Manufacturer: KAMOKA

• Material: Sheet Steel
• Control/Trailing Arm Type: Control Arm
• Fitting Position: Front Axle Left, Lower, Front Axle Right
• Weight [kg]: 3.037
• Supplementary Article/Supplementary Info: with bearings
• Supplementary Article/Info 2: without ball joint
• Manufacturer: FEBI BILSTEIN

Technical Information: Please tighten the mounting bolts with the wheels on the ground. General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Fitting Position: Front Axle Left, outer, Lower
• Cone Size [mm]: 14.9
• Supplementary Article/Info 2: with ball joint, with rubber mount
• Material: Steel
• Length [mm]: 391
• Control/Trailing Arm Type: Control Arm
• as standard:
• Thread Size: M12X1,5 RHT
• paired article number: 210042
• Weight [kg]: 3.494
• Installation Information: Important: Observe Fitting Instructions
• Manufacturer: A.B.S.

• Fitting Position: Rear Axle
• Control/Trailing Arm Type: Control Arm
• Length [mm]: 556
• Manufacturer: MAGNETI MARELLI

• Fitting Position: Front Axle Right, outer, Lower
• Cone Size [mm]: 14.9
• Supplementary Article/Info 2: with ball joint, with rubber mount
• Material: Steel
• Length [mm]: 391
• Control/Trailing Arm Type: Control Arm
• as standard:
• Thread Size: M12X1,5 RHT
• paired article number: 210043
• Weight [kg]: 3.486
• Installation Information: Important: Observe Fitting Instructions
• Manufacturer: A.B.S.

• Control/Trailing Arm Type: Control Arm
• Base body material: Steel
• Fitting Position: Front Axle Left
• Net weight [kg]: 2.93
• Diameter [mm]: 13
• paired article number: G40.3598/C
• Diameter 1 [mm]: 13
• Supplementary Article/Info 2: with ball joint
• Name: OMG G40.3599/C
• Manufacturer: OMG

• Control/Trailing Arm Type: Control Arm
• Base body material: Steel
• Fitting Position: Front Axle Right
• Net weight [kg]: 2,925
• Diameter [mm]: 13
• paired article number: G40.3599/C
• Diameter 1 [mm]: 13
• Supplementary Article/Info 2: with ball joint
• Name: OMG G40.3598/C
• Manufacturer: OMG

• paired article number: 30 91 9822
• Material: Sheet Steel
• Control/Trailing Arm Type: Control Arm
• Fitting Position: Front Axle Left, Lower
• Weight [kg]: 3.5
• Supplementary Article/Info 2: with ball joint
• Supplementary Article/Supplementary Info: with lock nuts, with bearings
• Manufacturer: SWAG
• Name: SW 30 91 9820

Technical Information: Please tighten the mounting bolts with the wheels on the ground. General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• paired article number: 30 91 9820
• Material: Sheet Steel
• Control/Trailing Arm Type: Control Arm
• Fitting Position: Front Axle Right, Lower
• Weight [kg]: 3.5
• Supplementary Article/Info 2: with ball joint
• Supplementary Article/Supplementary Info: with bearings, with lock nuts
• Manufacturer: SWAG
• Name: SW 30 91 9822

Technical Information: Please tighten the mounting bolts with the wheels on the ground. General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Fitting Position: Lower, Front Axle Right
• Control/Trailing Arm Design: Triangular Control Arm
• paired article number: VKDS 321102 B
• Control/Trailing Arm Type: Control Arm
• Supplementary Article/Supplementary Info: with synthetic grease
• Supplementary Article/Info 2: with ball joint
• Name: SK VKDS321103B
• Manufacturer: SKF

• Fitting Position: Lower, Front Axle Left
• Control/Trailing Arm Design: Triangular Control Arm
• paired article number: VKDS 321103 B
• Control/Trailing Arm Type: Control Arm
• Supplementary Article/Supplementary Info: with synthetic grease
• Supplementary Article/Info 2: with ball joint
• Name: SK VKDS321102B
• Manufacturer: SKF

• paired article number: 19820
• Material: Sheet Steel
• Control/Trailing Arm Type: Control Arm
• Fitting Position: Front Axle Right, Lower
• Weight [kg]: 3.5
• Supplementary Article/Supplementary Info: with lock nuts, with bearings
• Supplementary Article/Info 2: with ball joint
• Manufacturer: FEBI BILSTEIN

Technical Information: Please tighten the mounting bolts with the wheels on the ground. General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Fitting Position: Front Axle Right, Lower
• Thread Size 1: M12x1.25
• Thread Size 2: M12x1.25
• Material: Sheet Steel
• paired article number: TC786
• Control/Trailing Arm Type: Trailing Arm
• Supplementary Article/Info 2: with ball joint
• Length [mm]: 466
• Width [mm]: 156
• Manufacturer: DELPHI
• Name: DE TC787

• Fitting Position: Front Axle Left, Lower
• Thread Size 1: M12x1.25
• Thread Size 2: M12x1.25
• Material: Sheet Steel
• paired article number: TC787
• Control/Trailing Arm Type: Trailing Arm
• Supplementary Article/Info 2: with ball joint
• Length [mm]: 466
• Width [mm]: 156
• Manufacturer: DELPHI
• Name: DE TC786

• Control/Trailing Arm Type: Control Arm
• Fitting Position: Front Axle Left, Front Axle Right, Lower, outer
• Manufacturer: TRW

SVHC: No information available, please contact the manufacturer!

• Fitting Position: Front Axle, Left, Right, outer, Lower
• Weight [kg]: 3
• Required quantity: 2
• Control/Trailing Arm Type: Control Arm
• Supplementary Article/Info 2: with rubber mount, without ball joint
• Packaging length [cm]: 46
• Packaging width [cm]: 37
• Packaging height [cm]: 6
• Manufacturer: MONROE

• Fitting Position: Front Axle
• Control/Trailing Arm Type: Control Arm
• Material: Sheet Steel
• Supplementary Article/Info 2: without ball joint
• SVHC: No SVHC present!
• Manufacturer: FAG
• Name: LU 821034910

• Material: Sheet Steel
• Control/Trailing Arm Type: Control Arm
• Fitting Position: Front Axle Left, Lower, Front Axle Right
• Weight [kg]: 3.037
• Supplementary Article/Info 2: without ball joint
• Supplementary Article/Supplementary Info: with bearings
• Manufacturer: SWAG
• Name: SW 32 73 0016

Technical Information: Please tighten the mounting bolts with the wheels on the ground. General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Name: Control arm left
• Quality class: PJ

Lisainfo: "Tootja: TEKNOROT
A.A3/GOLFIV/OCT/TOL.
(kvaliteediklass: PJ)"

• Name: Control arm right
• Quality class: PJ

Lisainfo: "Tootja: TEKNOROT
A.A3/GOLFIV/OCT/TOL.
(kvaliteediklass: PJ)"

• Fitting Position: Front Axle Right
• Material: Sheet Steel
• Control/Trailing Arm Type: Control Arm
• paired article number: 49399127
• Name: COC 49399071
• Manufacturer: CORTECO

• Fitting Position: Front Axle Left
• Material: Sheet Steel
• Control/Trailing Arm Type: Control Arm
• paired article number: 49399071
• Name: COC 49399127
• Manufacturer: CORTECO

• Control/Trailing Arm Type: not for control arm
• Manufacturer: SKF
• Name: SK VKDS461000

• Fitting Position: Front Axle
• Control/Trailing Arm Type: Control Arm
• Weight [kg]: 1.84
• Name: DY 29-23959
• Manufacturer: DYS

• Control/Trailing Arm Type: Control Arm
• Fitting Position: Front Axle Right, Lower
• Length [mm]: 465
• Thread Size: M12 x 1,5
• Cone Size [mm]: 18
• paired article number: 79512AL
• Name: ALT 79507AL
• Manufacturer: ALTE AUTOMOTIVE

• Control/Trailing Arm Type: Control Arm
• Fitting Position: Front Axle Left, Lower
• Length [mm]: 465
• Thread Size: M12 x 1,5
• Cone Size [mm]: 18
• paired article number: 79507AL
• Name: ALT 79512AL
• Manufacturer: ALTE AUTOMOTIVE

• Fitting Position: Front Axle
• Control/Trailing Arm Type: Control Arm
• Weight [kg]: 1.83
• Name: DY 29-23736
• Manufacturer: DYS

• Control/Trailing Arm Type: Control Arm
• Fitting Position: Front Axle, both sides
• Material: Sheet Steel
• Article number of recommended accessories: 44091 01
• Manufacturer: LEMFÖRDER
• Name: LMI 2247503

SVHC: No information available, please contact the manufacturer!

• Control/Trailing Arm Type: Control Arm
• Fitting Position: Front Axle, Left
• Material: Steel
• Supplementary Article/Info 2: with bolts
• paired article number: FT15535
• Manufacturer: FAST

• Fitting Position: Front Axle Left
• Steering: with tie rod ends
• Control/Trailing Arm Type: Control Arm
• Manufacturer: VIKA

General Information: Wishbone arm for lower control;front left;with ball

• Control/Trailing Arm Type: Control Arm
• Fitting Position: Front Axle Right, Lower
• External Thread 2 [mm]: M12x1,5
• Weight [kg]: 3.56
• Manufacturer: RTS

• Control/Trailing Arm Type: Control Arm
• Fitting Position: Front Axle Left, Lower
• External Thread 2 [mm]: M12x1,5
• Weight [kg]: 3.56
• Manufacturer: RTS

• Control/Trailing Arm Type: Control Arm
• Fitting Position: Front Axle both sides, Lower
• Weight [kg]: 2.947
• Manufacturer: RTS

• Fitting Position: Front Axle, Right, outer, Lower
• Weight [kg]: 3.6
• Control/Trailing Arm Type: Control Arm
• Supplementary Article/Info 2: with ball joint, with rubber mount
• paired article number: L29546
• Packaging length [cm]: 49
• Packaging width [cm]: 37
• Packaging height [cm]: 9
• Manufacturer: MONROE

• Engine Code: AXR
• for OE number: 1K0 407 151 AC
• Fitting Position: Front Axle Left
• Supplementary Article/Info 2: with rubber mount, with ball joint
• Control/Trailing Arm Type: for control arm
• Quantity Unit: Set
• Axle alignment required after fitting:
• paired article number: V10-3929
• Weight [kg]: 1.6
• Manufacturer: VAICO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Fitting Position: Front Axle, Left, outer, Lower
• Weight [kg]: 3.6
• Control/Trailing Arm Type: Control Arm
• Supplementary Article/Info 2: with ball joint, with rubber mount
• paired article number: L29545
• Packaging length [cm]: 49
• Packaging width [cm]: 37
• Packaging height [cm]: 9
• Manufacturer: MONROE

• Fitting Position: Front Axle Left
• Control/Trailing Arm Type: Control Arm
• Manufacturer: MAGNETI MARELLI

• Engine Code: AXR
• Supplementary Article/Info 2: with rubber mount, with ball joint
• paired article number: V10-3909
• for OE number: 1K0 407 152 AC
• Control/Trailing Arm Type: for control arm
• Quantity Unit: Set
• Axle alignment required after fitting:
• Fitting Position: Front Axle Right
• Weight [kg]: 1.57
• Manufacturer: VAICO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Fitting Position: Front Axle Left
• Control/Trailing Arm Type: Control Arm
• Supplementary Article/Info 2: with ball joint
• Material: Sheet Steel
• Thread Size: M12x1,5
• Length [mm]: 347
• Replace in pairs only:
• reinforced version:
• Width [mm]: 277
• with environmental seal: Carbon neutral
• Required quantity: 1
• paired article number: 116 050 0010/HD
• Manufacturer: MEYLE

General Information: Improved performance and service life: larger ball pin life: larger ball pin diameter of MEYLE-HD ball joint distributes forces over a larger surface area and minimizes part wear.

• Fitting Position: Front Axle
• Guarantee: 3 years guarantee
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY
• Name: CE 04SKV960

• Fitting Position: Front Axle
• Supplementary Article/Supplementary Info: with attachment material, with holder
• Control/Trailing Arm Type: Control Arm
• Steering: with tie rod ends
• Stabiliser Bar Diameter [mm]: 23
• Quantity per axle: 1
• Full Set:
• for components see parts list:
• Axle alignment required after fitting:
• Manufacturer: TOPRAN

Supplementary Article/Info 2: with axle joint, with rubber mount, with coupling rod, with ball joint General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Full Set:
• Fitting Position: Front Axle
• Material: Steel
• Weight [kg]: 7.4
• Installation Information: Important: Observe Fitting Instructions
• Manufacturer: A.B.S.

• Fitting Position: Front Axle
• Weight [kg]: 9.22
• Guarantee: 3 years guarantee
• Always compare old and new part (in particular OE No.):
• Name: CE 04SKV270
• Manufacturer: ESEN SKV